Ong Soon An
Thumbnail Image
Preferred name
Ong Soon An
Official Name
Ong, Soon An
Alternative Name
Ong, Soon An
Ong, S. A.
Soon An, Ong
Soon-An, Ong
ONG, Soon An
Ong, Soon an
Soon-An, Ong
Main Affiliation
Scopus Author ID
57201387782
Researcher ID
B-9255-2012

Research Output

Filters

84
Reset filters

Settings
Now showing 1 - 10 of 84
  • Publication
    Enhanced photodegradation of phenol by ZnO nanoparticles synthesized through sol-gel method
    ( 2017-12-01)
    Nik Noor Athirah Nik Yusoff
    ;
    Ho Li Ngee
    ;
    Ong Soon An
    ;
    Wong Yee Shian
    ;
    Wan Fadhilah Khalik
    ;
    Fahmi Ridzwan
    Zinc oxide (ZnO) utilization in advanced oxidation process (AOP) via solar-photocatalytic process was a promising method for alternative treating wastewater containing phenol. The ZnO photocatalyst semiconductor was synthesized by sol-gel method. The morphology of the ZnO nanostructures was observed by using scanning electron microscope (SEM) and the crystallite phase of the ZnO was confirmed by x-ray diffraction (XRD). The objective of this study was to synthesis ZnO nanoparticles through a sol-gel method for application as a photocatalyst in the photodegradation of phenol under solar light irradiation. The photodegradation rate of phenol increased with the increasing of ZnO loading from 0.2 until 1.0 g. Only 2 h were required for synthesized ZnO to fully degrade the phenol. The synthesized ZnO are capable to totally degrade high initial concentration up until 45 mg L-1 within 6 h of reaction time. The photodegradation of phenol by ZnO are most favoured under the acidic condition (pH3) where the 100% removal achieved after 2 h of reaction. The mineralization of phenol was monitored through chemical oxygen demand (COD) reduction and 92.6% or removal was achieved. This study distinctly utilized natural sunlight as the sole sources of irradiation which safe, inexpensive; to initiate the photocatalyst for degradation of phenol.
  • Publication
    Synergistic Effect Between Iron and Food/Microorganism (F/M) Ratio in Biological Wastewater Treatment
    ( 2022-01-01)
    Subramaniam L.S.
    ;
    Nabilah Aminah Lutpi
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Nazerry Rosmady Rahmat
    ;
    Siripatana C.
    Biological wastewater treatment is mainly dependent on the actions of microorganisms that can be used to treat wastewater. Microorganisms will start to stick together when they degrade the organic matter in wastewater for food and flocculate to settle the pollutants. This study aimed to investigate the effect of food to microorganism (F/M) ratio and iron in a biological process using aerobic treatment. For this purpose, four aerobic tanks (A, B, C, D) were set up using activated sludge as the seed sludge, air pump as air diffuser to provide oxygen to the system, and three litres of synthetic medium as carbon source for each tank. A specific amount of iron (II) sulfate was added into tanks B, C, and D with the weight of 3 g, 6 g, and 9 g, respectively. Tank A act as a control, and no iron dosage was added. The F/M ratio for tanks A, B, C, and D were 0.8, 0.5, 0.4, and 0.3 mg BOD/mg MLVSS, respectively. The aerobic tanks were operated for 40 days in sequential batch mode and sampling was collected four times per week to observe the COD and MLVSS. This study has found that Tank D shows the best performance compared to all tanks with 84.71% COD removal efficiency and a fivefold increment of microorganism growth rate. These findings suggest that a relationship exists between the iron and F/M ratio to enhance the aerobic treatment process.
  • Publication
    Biotreatment of sulfonated dyestuffs with energy recovery in microbial fuel cell: Influencing parameters, kinetics, degradation pathways, mechanisms, and phytotoxicity assessment
    ( 2021-08-01)
    Tan S.M.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Y.S.
    ;
    Che Zulzikrami Azner Abidin
    ;
    Thung W.E.
    ;
    Teoh T.P.
    Removal of recalcitrant sulfonated dyestuff intermediates from wastewater has been an urgent challenge for environmental technologies. In this regard, the biodegradations of monoazo Methyl Orange (MO) and diazo dyes Reactive Black 5 (RB5) towards wastewater treatment and bioelectricity generation in microbial fuel cell were investigated and compared through the studies on azo dye concentration, aeration, sampling points arrays, and electrode spacings. The degradation of diazo RB5 yielded higher chemical oxygen demand removal, decolourization efficiencies, and power generation over monoazo MO. The decolourization efficiency of RB5 (97.62%) increased with an increase of RB5 concentration (50 mg/L), suggesting that the system has the capability of removing higher RB5 concentration. However, contrary results were obtained with MO due to its toxicity. This study also demonstrated that the decolourization rate of diazo RB5 (0.1533 h-1) was ≈ 53% higher than monoazo MO (0.0727 h-1). The findings revealed that the degradation kinetic was remarkably influenced by the chemical structure of dye, where dye with more electron-withdrawing groups at para position are more susceptible to be reduced. Higher output voltage (568.59 mV) and power generation (108.87 mW/m2) were attained with RB5 due to electron donor availability and electron-shuttling characteristics of RB5 decolourized intermediates. Furthermore, detailed degradation pathways of MO and RB5 were presented based on the UV-vis and GC-MS results. The phytotoxicity assessment via Sorghum bicolor seeds had further verified the reduction in toxicity after the treatment of azo dyes.
  • Publication
    Biohydrogen production from palm oil mill effluent with Moringa Oleifera seeds as support carrier in attached growth system
    ( 2020-06-10)
    Hamid W.Z.W.A.
    ;
    Nabilah Aminah Lutpi
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Malek M.A.
    Biohydrogen production by dark fermentation is one of the attracting alternatives for renewable energy in worldwide. By employing immobilized cells, hydrogen production and cell density could be improved. This study aimed to investigate the efficiency of Moringa Oleifera Seeds (MOS) immobilized cells in enhancing the biohydrogen production using repeated batch fermentation under mesophilic condition, 37°C. The efficiency of MOS as support carrier, effect of the initial pH (5.0-7.0) and performance of raw and diluted Palm Oil Mill Effluent (POME) using MOS immobilized cells were investigated using anaerobic sludge as inoculums. The cumulative hydrogen production results were fitted into a modified Gompertz equation to find the maximum hydrogen production. MOS immobilized cells was more efficient in producing hydrogen compare to suspended cells (without MOS). The optimal pH obtained using MOS immobilized cells was found to be at pH 6 using raw POME with the maximum hydrogen production (Hm) of 122 mL, the maximum hydrogen production rate (Rm) of 39.0 mL/h, and 560 ppm of hydrogen concentration.
  • Publication
    Decolorization and mineralization of Amaranth dye using multiple zoned aerobic and anaerobic baffled constructed wetland
    ( 2017-08-03)
    Harvinder Kaur Lehl
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Farah Naemah Mohd Saad
    ;
    Oon Yoong Ling
    ;
    Oon Yoong Sin
    ;
    Thung Wei Eng
    ;
    Yong Chin Yii
    The objective of this study is to determine the reduction efficiency of Chemical Oxygen Demand (COD) as well as the removal of color and Amaranth dye metabolites by the Aerobic–anaerobic Baffled Constructed Wetland Reactor (ABCW). The ABCW reactor was planted with common reed (Phragmite australis) where the hydraulic retention time (HRT) was set to 1 day and was fed with synthetic wastewater with the addition of Amaranth dye. Supplementary aeration was supplied in designated compartments of the ABCW reactor to control the aerobic and anaerobic zones. After Amaranth dye addition the COD reduction efficiency dropped from 98 to 91% while the color removal efficiency was 100%. Degradation of azo bond in Amaranth dye is shown by the UV–Vis spectrum analysis which demonstrates partial degradation of Amaranth dye metabolites. The performance of the baffled unit is due to the longer pathway as there is the up-flow and down-flow condition sequentially, thus allowing more contact of the wastewater with the rhizomes and micro-aerobic zones.
  • Publication
    Polypropylene biofilm carrier and fabricated stainless steel mesh supporting activated carbon: Integrated configuration for performances enhancement of microbial fuel cell
    ( 2021-08-01)
    Tan S.M.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Y.S.
    ;
    Che Zulzikrami Azner Abidin
    ;
    Thung W.E.
    ;
    Teoh T.P.
    The mass transfer resistance at the anode and the reduction of oxygen at the cathode are currently perceived as two major bottlenecks of microbial fuel cells. To overcome these issues, an integrated configuration was developed for performances enhancement on simultaneous bioelectricity generation and wastewater treatment in single chamber up-flow membrane-less microbial fuel cell (UFML-MFC). Polypropylene biofilm carriers were used as anodic packing materials and fabricated stainless steel mesh holder supporting activated carbon flakes (CF/SM) was employed as biocathode configuration in this study. The employments of polypropylene carriers and CF/SM enhanced not only the active surface area and microbial adhesion, but also the mass transfer of MFC system. The maximum output voltage, power and current generation achieved in this system were 615 mV, 162.59 mW/m2 and 468.74 mA/m2, respectively. In terms of wastewater treatment performance, UFML-MFC achieved 85.6% and 95.7% of COD and NH4+ removal, respectively. The COD reduction in closed circuit was 9.87% better than open circuit due to stimulation of electrochemical-active bacteria for electron transfer to the anode, which favoured organic matter degradation. The enrichment of electrogenic bacteria at A3, which was largest electrode spacing (23 cm) in the system resulted a higher voltage and power output compared to A1 (11 cm) and A2 (17 cm). Besides, the energy performances of this MFC system were also evaluated based on NERs (1.074 kWh/kg COD), NERv (22.86 Wh/m3) and CE (10.42%).
  • Publication
    Innovative baffled microbial fuel cells for azo dye degradation: Interactive mechanisms of electron transport and degradation pathway
    ( 2021-05-01)
    Oon Y.S.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Oon Y.L.
    ;
    Lehl H.K.
    ;
    Thung W.E.
    Two membrane-less baffled microbial fuel cells (BMFCs) were developed for non-dye (BMFC1) and dye degradation (BMFC2) investigations along with simultaneous bioelectricity generation. The influence of salinity, organic loading, circuit connection, aeration rate, dye concentration and addition of intermediates on BMFCs performances were evaluated systematically. The increase of salinity by 3-fold (0.39 g/L of NaCl) lowered the internal resistance of BMFC1 system by 38%–620 Ω, and the power density increased 49% to 10.55 ± 0.86 mW/m2. While the further increase of salinity (10-fold) adversely affected BMFC1. The power performance of BMFC1 improved with higher organic loading. Whereas, the increment in organic loading enhanced the decolourisation efficiency but deteriorated the power performance of BMFC2 ascribed to the competition between New Coccine (NC) molecules and anode for electrons. This finding corroborates that NC was a preferable electron acceptor than the anode. The addition of 50 mg/L NC increased the power density by 53% to 12.40 ± 1.60 mW/m2, which revealed that NC decolourised intermediates could act as the electron mediator, hence led to the increase of power performance. The electron-mediating mechanism of NC decolourised intermediate, 1-amino-2-naphthol-6,8-disulfonate as electron shuttle was unveiled. The in-depth understanding of the mechanisms involved in dye degradation in MFCs was presented, where a comprehensive degradation pathway of NC was proposed based on the intermediates identified via UV–Visible spectra, Fourier-transform infrared spectroscopy (FTIR), high-performance liquid chromatography (HPLC) and gas chromatograph-mass spectrometer (GC-MS) analyses.
  • Publication
    Transformation from biofiltration unit to hybrid constructed wetland-microbial fuel cell: Improvement of wastewater treatment performance and energy recovery
    ( 2023-05-01)
    Teoh T.P.
    ;
    Koo C.J.
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Nabilah Aminah Lutpi
    ;
    Tan S.M.
    ;
    Yap K.L.
    ;
    Ong Soon An
    This study aimed to compare the performance of biofiltration, constructed wetland, and constructed wetland microbial fuel cell (CW-MFC). The transformation from a biofiltration unit to a hybrid CW-MFC was demonstrated with the advantages of improvement of wastewater treatment while generating electricity simultaneously. The introduction of plants to the upper region of the bioreactor enhanced the DO level by 0.8 mg/L, ammonium removal by 5 %, and COD removal by 1 %. The integration of electrodes and external circuits stimulated the degradation rate of organic matter in the anodic region (1 % without aeration and 3 % with aeration) and produced 5.13 mW/m3 of maximum power density. Artificial aeration improved the nitrification efficiency by 38 % and further removed the residual COD to an efficiency of 99 %. The maximum power density was also increased by 3.2 times (16.71 mW/m3) with the aid of aeration. In treating higher organic loading wastewater (3M), the maximum power density showed a significant increment to 78.01 mW/m3 (4.6-fold) and the COD removal efficiency was 98 %. The ohmic overpotential dominated the proportion of total loss (67-91 %), which could be ascribed to the low ionic conductivity. The reduction in activation and concentration loss contributed to the lower internal resistance with the additional aeration and higher organic loading. Overall, the transformation from biofiltration to a hybrid CW-MFC system is worthwhile since the systems quite resemble while CW-MFC could improve the wastewater treatment as well as recover energy from the treated wastewater.
  • Publication
    Hydroxyl radical formation in the hybrid system of photocatalytic fuel cell and peroxi-coagulation process affected by iron plate and UV light
    ( 2020-04-01)
    Nordin N.
    ;
    Ho Li Ngee
    ;
    Ong Soon An
    ;
    Ibrahim A.H.
    ;
    Abdul Latif Abdul Rani
    ;
    Lee S.L.
    ;
    Ong Y.P.
    The hybrid electrochemical system of photocatalytic fuel cell - peroxi-coagulation (PFC-PC) is a combined technology of advanced oxidation process (AOP) which involve the hydroxyl radical formation for simultaneous degradation of organic pollutant and electricity generation. The p-nitrosodimethylaniline (RNO) spin trapping technique was applied by analyzing the RNO bleaching performance to detect the OH[rad] at the PFC and PC reactors. The presence of UV light showed higher RNO bleaching rate at the PFC reactor (11.7%) with maximum power density (Pmax = 3.14 mW cm−2). Results revealed that the optimum of maximum power density was observed at iron plate size of 30 cm2. UV light became a limiting factor in the PFC system as a power source in the PFC-PC system. Meanwhile, iron plate plays an important role to supply the soluble Fe2+ ions by oxidation process and become a suitable catalyst for in-situ production of H2O2 and OH[rad] through the PC process to degrade the organic molecules.
  • Publication
    Comparative study on the biodegradation of mixed remazol dyes wastewater between integrated anaerobic/aerobic and aerobic sequencing batch reactors
    ( 2017-09-01)
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Khairil Anuar Mohammad Pakri
    Complete mineralization of dye effluent was realized through sequential anaerobic followed by aerobic processes. The aim of this study was to evaluate and compare the degradation of wastewater of four remazol dyes with integrated anaerobic/aerobic (SBR1) and aerobic (SBR2) processes under sequencing batch reactor operation. The ORP profiles show that the SBR1 was in anaerobic condition during the 15 h React mode and turned to aerobic condition through air aeration for 3 h. The SBR1 and SBR2 achieved almost similar performance in the removal of organic compounds with average 95% COD removal. The SBR1 performed better in the color removal with 93% removal efficiency while the SBR2 only attained 50% removal efficiency. The biodegradation rate of the remazol dyes was well described by the first-order kinetic model with the sequence degradation rate remazol pink > remazol violet > remazil yellow > remazol green.