Nabilah Aminah Lutpi
Thumbnail Image
Preferred name
Nabilah Aminah Lutpi
Official Name
Nabilah Aminah, Lutpi
Alternative Name
Lutpi, N. A.
Lutpi, Nabilah A.
Aminah, L. Nabilah
Lutpi, Nabilah Aminah
Aminah Lutpi, Nabilah
Main Affiliation
Scopus Author ID
55793936400
Researcher ID
M-9374-2019

Research Output

Filters

37
Reset filters

Settings
Now showing 1 - 10 of 37
  • Publication
    Synergistic Effect Between Iron and Food/Microorganism (F/M) Ratio in Biological Wastewater Treatment
    ( 2022-01-01)
    Subramaniam L.S.
    ;
    Nabilah Aminah Lutpi
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Nazerry Rosmady Rahmat
    ;
    Siripatana C.
    Biological wastewater treatment is mainly dependent on the actions of microorganisms that can be used to treat wastewater. Microorganisms will start to stick together when they degrade the organic matter in wastewater for food and flocculate to settle the pollutants. This study aimed to investigate the effect of food to microorganism (F/M) ratio and iron in a biological process using aerobic treatment. For this purpose, four aerobic tanks (A, B, C, D) were set up using activated sludge as the seed sludge, air pump as air diffuser to provide oxygen to the system, and three litres of synthetic medium as carbon source for each tank. A specific amount of iron (II) sulfate was added into tanks B, C, and D with the weight of 3 g, 6 g, and 9 g, respectively. Tank A act as a control, and no iron dosage was added. The F/M ratio for tanks A, B, C, and D were 0.8, 0.5, 0.4, and 0.3 mg BOD/mg MLVSS, respectively. The aerobic tanks were operated for 40 days in sequential batch mode and sampling was collected four times per week to observe the COD and MLVSS. This study has found that Tank D shows the best performance compared to all tanks with 84.71% COD removal efficiency and a fivefold increment of microorganism growth rate. These findings suggest that a relationship exists between the iron and F/M ratio to enhance the aerobic treatment process.
  • Publication
    Biohydrogen production from palm oil mill effluent with Moringa Oleifera seeds as support carrier in attached growth system
    ( 2020-06-10)
    Hamid W.Z.W.A.
    ;
    Nabilah Aminah Lutpi
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Malek M.A.
    Biohydrogen production by dark fermentation is one of the attracting alternatives for renewable energy in worldwide. By employing immobilized cells, hydrogen production and cell density could be improved. This study aimed to investigate the efficiency of Moringa Oleifera Seeds (MOS) immobilized cells in enhancing the biohydrogen production using repeated batch fermentation under mesophilic condition, 37°C. The efficiency of MOS as support carrier, effect of the initial pH (5.0-7.0) and performance of raw and diluted Palm Oil Mill Effluent (POME) using MOS immobilized cells were investigated using anaerobic sludge as inoculums. The cumulative hydrogen production results were fitted into a modified Gompertz equation to find the maximum hydrogen production. MOS immobilized cells was more efficient in producing hydrogen compare to suspended cells (without MOS). The optimal pH obtained using MOS immobilized cells was found to be at pH 6 using raw POME with the maximum hydrogen production (Hm) of 122 mL, the maximum hydrogen production rate (Rm) of 39.0 mL/h, and 560 ppm of hydrogen concentration.
  • Publication
    Transformation from biofiltration unit to hybrid constructed wetland-microbial fuel cell: Improvement of wastewater treatment performance and energy recovery
    ( 2023-05-01)
    Teoh T.P.
    ;
    Koo C.J.
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Nabilah Aminah Lutpi
    ;
    Tan S.M.
    ;
    Yap K.L.
    ;
    Ong Soon An
    This study aimed to compare the performance of biofiltration, constructed wetland, and constructed wetland microbial fuel cell (CW-MFC). The transformation from a biofiltration unit to a hybrid CW-MFC was demonstrated with the advantages of improvement of wastewater treatment while generating electricity simultaneously. The introduction of plants to the upper region of the bioreactor enhanced the DO level by 0.8 mg/L, ammonium removal by 5 %, and COD removal by 1 %. The integration of electrodes and external circuits stimulated the degradation rate of organic matter in the anodic region (1 % without aeration and 3 % with aeration) and produced 5.13 mW/m3 of maximum power density. Artificial aeration improved the nitrification efficiency by 38 % and further removed the residual COD to an efficiency of 99 %. The maximum power density was also increased by 3.2 times (16.71 mW/m3) with the aid of aeration. In treating higher organic loading wastewater (3M), the maximum power density showed a significant increment to 78.01 mW/m3 (4.6-fold) and the COD removal efficiency was 98 %. The ohmic overpotential dominated the proportion of total loss (67-91 %), which could be ascribed to the low ionic conductivity. The reduction in activation and concentration loss contributed to the lower internal resistance with the additional aeration and higher organic loading. Overall, the transformation from biofiltration to a hybrid CW-MFC system is worthwhile since the systems quite resemble while CW-MFC could improve the wastewater treatment as well as recover energy from the treated wastewater.
  • Publication
    Photocatalytic Degradation of Sugarcane Vinasse Using ZnO Photocatalyst: Operating Parameters, Kinetic Studies, Phytotoxicity Assessments, and Reusability
    ( 2022-02-01)
    Kee W.C.
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Nabilah Aminah Lutpi
    ;
    Sam Sung Ting
    ;
    Audrey Chai Yee Chieh
    ;
    Eng K.M.
    Abstract: Photocatalytic degradation performance is highly related to optimized operating parameters such as initial concentration, pH value, and catalyst dosage. In this study, the impact of various parameters on the photocatalytic degradation of anaerobically digested vinasse (AnVE) has been determined through decolourization and chemical oxygen demand (COD) reduction efficiency using zinc oxide (ZnO) photocatalyst. In this context, the application of photocatalytic degradation in treating sugarcane vinasse using ZnO is yet to be explored. The COD reduction efficiency and decolourization achieved 83.40% and 99.29%, respectively, under the conditions of 250 mg/L initial COD concentration, pH 10, and 2.0 g/L catalyst dosage. The phytotoxicity assessment was also conducted to determine the toxicity of AnVE before and after treatment using mung bean (Vigna radiata). The reduction of root length and the weight of mung bean indicated that the sugarcane vinasse contains enormous amounts of organic substances that affect the plant's growth. The toxicity reduction in the AnVE solution can be proved by UV–Vis absorption spectra. Furthermore, the catalyst recovery achieved 93% in the reusability test. However, the COD reduction efficiency and decolourization were reduced every cycle. It was due to the depletion of the active sites in the catalyst with the adsorption of organic molecules. Thus, it can be concluded that the photocatalytic degradation in the treatment of AnVE was effective in organic degradation, decolorization, toxicity reduction and can be reused after the recovery process. Graphical abstract: [Figure not available: see fulltext.].
  • Publication
    Effect of operating temperature in the anaerobic degradation of palm oil mill effluent: Process performance, microbial community, and biokinetic evaluation
    ( 2022-09-01)
    Audrey Chai Yee Chieh
    ;
    Wong Yee Shian
    ;
    Ong Soon An
    ;
    Nabilah Aminah Lutpi
    ;
    Sam Sung Ting
    ;
    Kee Wei Chin
    This research paper presents the thermophilic anaerobic digestion (TAD) of palm oil mill effluent (POME), which is an extension of a previously conducted mesophilic anaerobic digestion (MAD) study. An anaerobic suspended growth closed bioreactor was operated at various hydraulic retention times (HRT) between 24 and 8 days. The effect of operating temperature on the performance, microbial identification, and biokinetic coefficients was evaluated. Performance was quantified by the production of biogas and the chemical oxygen demand (COD) reduction efficiency. Biogas production in TAD (64.56 L/day) was higher than MAD (46.76 L/day). A higher COD reduction efficiency was also achieved in TAD (90.90%) compared to MAD (89.66%). Other than that, more species of methanogenic bacteria were also identified in TAD through 16S rDNA. Furthermore, the modified Monod model implemented in the biokinetic evaluation revealed that higher values of maximum substrate utilization rate (rx,max) and maximum specific biomass growth rate (μmax) contributed to the better performance in TAD. The high rx,max value explains the higher COD reduction efficiency obtained in TAD. The critical retention time (θC) in TAD is also higher than MAD, making it less prone to the washout of active microbes when operating near low retention times. Additionally, TAD also achieved higher methane yield (YCH4) as opposed to MAD. The extension study concluded that the TAD of POME demonstrated improved performance in terms of biogas production and COD reduction when evaluated against the previously conducted MAD.
  • Publication
    Caffeine-containing wastewater treatment and bioelectricity generation in up-flow constructed wetland-microbial fuel cell: Influence of caffeine concentration, operating conditions, toxicity assessment, and degradation pathway
    ( 2022-04-01)
    Teoh T.P.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Nabilah Aminah Lutpi
    ;
    Oon Y.L.
    ;
    Tan S.M.
    ;
    Ong Y.P.
    ;
    Yap K.L.
    This study explored the potential of caffeine being utilized as the fuel for the microbes to produce electrons for electricity generation in up-flow constructed wetland-microbial fuel cell (UFCW-MFC). The effect of caffeine concentration was investigated to identify the availability of UFCW-MFC in the conversion of caffeine to electrons for electricity production; and the effect of operating conditions (circuit connection, supplementary aeration, and plant) was studied to determine their significance in the treatment of caffeine containing wastewater. The UFCW-MFC achieved about 98% of decaffeination efficiency regardless of caffeine concentration; while a decrease of efficiency was observed when UFCW-MFC operated without supplementary aeration and plant (~93%). COD removal efficiency decreased correspondingly to the increase of caffeine concentration, which could be contributed by the higher concentration of caffeine and its intermediates. The degradation pathway of caffeine in UFCW-MFC was explored in this study. It was remarkable that ammonia was produced and converted to ammonium ions during caffeine catabolism. Supplementary aeration and macrophyte play a crucial role in removing excess caffeine, intermediates as well as accumulated ammonium ions. The toxicity assessment revealed that caffeine was degraded to less toxic products. The closed circuit connection not only contributed to electricity generation but also enhanced the caffeine and COD removal efficiency by 4.6 and 5.4% in the anaerobic region, respectively. The increase of voltage and maximum power density from phase I to phase IV indicated that caffeine could be converted to electrons by the anaerobes for electricity production.
  • Publication
    Insights into the decolorization of mono and diazo dyes in single and binary dyes containing wastewater and electricity generation in up-flow constructed wetland coupled microbial fuel cell
    ( 2023-02-01)
    Teoh T.P.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Nabilah Aminah Lutpi
    ;
    Oon Y.L.
    ;
    Tan S.M.
    ;
    Ong Y.P.
    ;
    Yap K.L.
    The treatment of single and binary azo dyes, as well as the effect of the circuit connection, aeration, and plant on the performance of UFCW-MFC, were explored in this study. The decolorization efficiency of Remazol Yellow FG (RY) (single dye: 98.2 %; binary dye: 92.3 %) was higher than Reactive Black 5 (RB5) (single: 92.3 %; binary: 86.7 %), which could be due to monoazo dye (RY) requiring fewer electrons to break the azo bond compared to the diazo dye (RB5). In contrast, the higher decolorization rate of RB5 in binary dye indicated the removal rate was affected by the electron-withdrawing groups in the dye structure. The closed circuit enhanced about 2% of color and 4% of COD removal. Aeration improved the COD removal by 6%, which could be contributed by the mineralization of intermediates. The toxicity of azo dyes was reduced by 11–26% and the degradation pathways were proposed. The dye removal by the plants was increased with a higher contact time. RB5 was more favorable to be uptook by the plant as RB5 holds a higher partial positive charge. 127.39 (RY), 125.82 (RB5), and 58.66 mW/m3 (binary) of maximum power density were generated. The lower power production in treating the binary dye could be due to more electrons being utilized for the degradation of higher dye concentration. Overall, the UFCW-MFC operated in a closed circuit, aerated, and planted conditions achieved the optimum performance in treating binary azo dyes containing wastewater (dye: 87–92%; COD: 91%) compared to the other conditions (dye: 83–92%; COD: 78–87%).
  • Publication
    Sulfur dioxide removal using deep eutectic solvent–functionalized palm kernel shell–activated carbon
    (Springer, 2025-02)
    Wan Nur Amanna Wan Nuzi
    ;
    Muhammad Adli Hanif
    ;
    Naimah Ibrahim
    ;
    Farrah Aini Dahalan
    ;
    Nabilah Aminah Lutpi
    ;
    Masitah Hasan
    ;
    Raja Nazrul Hakim Raja Nazri
    ;
    Umi Fazara Md Ali
    The release of SOâ‚‚ into the atmosphere is concerning due to its role in acidification, which threatens living organisms and the environment. Adsorption processes using materials like chemically modified activated carbon (AC) have demonstrated strong potential for removing SOâ‚‚ before its release. This study evaluates the performance of AC derived from palm kernel shells, and AC functionalized with choline chloride-glycerol, a deep eutectic solvent (DES) (AC-DES), in removing SOâ‚‚ through breakthrough experiments conducted in a fixed bed reactor. AC and AC-DES achieved SOâ‚‚ adsorption capacities of 0.522 and 2.763 mg SOâ‚‚/g adsorbent, respectively. Characterization of the adsorbents indicated that DES functionalization significantly increased the number of active sites for SOâ‚‚ adsorption, leading to superior adsorption performance of AC-DES. The optimization of process parameters identified 40 Â°C and 1500 ppm inlet SOâ‚‚ concentration as the ideal conditions for optimal SOâ‚‚ adsorption. Experimental data fitted with three adsorption kinetic and isotherm models indicated that SOâ‚‚ adsorption onto AC-DES is best described by the Avrami kinetic model and the Sips isotherm model. Thermodynamics studies revealed that the process is exothermic, thermodynamically non-spontaneous, and goes from a random state to an ordered one. The findings suggest that SOâ‚‚ adsorption onto AC-DES follows a complex mixed mechanism involving both physisorption and chemisorption, with surface heterogeneity and adsorbate-adsorbent interactions playing a critical role in controlling the adsorption process.
  • Publication
    Kinetic Study of Substrate Inhibition on the Anaerobic Degradation of Sugarcane Vinasse
    ( 2023-10-04)
    Audrey Chai Yee Chieh
    ;
    Wong Yee Shian
    ;
    Kee Wei Chin
    ;
    Ong Soon An
    ;
    Nabilah Aminah Lutpi
    ;
    Sam Sung Ting
    Sugarcane vinasse was utilized as a substrate in thermophilic anaerobic degradation operated at hydraulic retention time (HRT) of 35 to 15 days, corresponding to organic loading rate (OLR) of 2.14 to 5.00 kg COD/m3.day. This study focuses on the soluble chemical oxygen demand (sCOD) reduction performance, kinetic evaluation through substrate inhibition model and model selection through the Akaike information criterion (AIC). The efficiency of sCOD reduction reached 84.7 % at OLR of 2.14 kg COD/m3.day and declined significantly to 51.4 % at OLR of 5.00 kg COD/m3.day. The Solver tool in Microsoft Office Excel was used to fit experimental data to the substrate inhibition models in the evaluation of the maximum specific substrate utilization rate (rxmax), substrate saturation constant (KS) and substrate inhibition constant (Ki). Model discrimination was performed using AIC and Tessier model was selected as the best fitted model with the highest likelihood of occurrence. Kinetic evaluation through the Tessier model gives: rxmax = 14.6745 /day, KS = 16.3218 and Ki = 16.9691.
      6  39
  • Publication
    Enhancement of energy recovery from caffeine wastewater in constructed wetland-microbial fuel cell through operating conditions
    ( 2023-01-01)
    Teoh T.P.
    ;
    Ong Soon An
    ;
    Ho Li Ngee
    ;
    Wong Yee Shian
    ;
    Nabilah Aminah Lutpi
    ;
    Tan S.M.
    ;
    Ong Y.P.
    ;
    Yap K.L.
    The enhancement of up-flow constructed wetland-microbial fuel cell (UFCW-MFC) performance in energy retrieval from caffeine containing wastewater has been explored via various operating conditions (hydraulic retention time (HRT), multianode (MA), multicathode current collector (MC), external resistance). The anaerobic decaffeination and COD removal improved by 37 and 12% as the HRT extended from 1 to 5 d. The increment in contact time between the microbes and organic substrates promoted the degradation and contributed to higher power output (3.4-fold), CE (eightfold), and NER (14–16-fold). The MA and MC connections facilitated the electron transfer rate and the degradation rate of organic substrates in the multiple anodic zones, which enhanced the removal efficiency in the anaerobic compartment (Caffeine: 4.2%; COD: 7.4%) and led to higher electricity generation (Power: 4.7-fold) and energy recovery (CE: 1.4-fold; NER: 2.3–2.5-fold) compared to SA. The lower external resistance favored the growth of electrogens and induced higher electron flux, where the best treatment performance and electricity production was obtained when the external resistance approached the internal resistance. Overall, it was noteworthy that the optimum operating conditions were achieved with 5 d HRT, MA, and MC connection along with external resistance of 200 Ω, which significantly outperformed the initial conditions (1 d HRT, SA connection, and 1000 Ω) by 43.7 and 29.8% of caffeine and COD removal in the anaerobic compartment, respectively as well as 14-fold of power generation.
      17  2