Nabilah Aminah Lutpi
Thumbnail Image
Preferred name
Nabilah Aminah Lutpi
Official Name
Nabilah Aminah, Lutpi
Alternative Name
Lutpi, N. A.
Lutpi, Nabilah A.
Aminah, L. Nabilah
Lutpi, Nabilah Aminah
Aminah Lutpi, Nabilah
Main Affiliation
Scopus Author ID
55793936400
Researcher ID
M-9374-2019

Research Output

Filters

36
Reset filters

Settings
Now showing 1 - 10 of 36
Thumbnail Image
Publication

Synergistic Effect Between Iron and Food/Microorganism (F/M) Ratio in Biological Wastewater Treatment

2022-01-01 , Subramaniam L.S. , Nabilah Aminah Lutpi , Wong Yee Shian , Ong Soon An , Nazerry Rosmady Rahmat , Siripatana C.

Biological wastewater treatment is mainly dependent on the actions of microorganisms that can be used to treat wastewater. Microorganisms will start to stick together when they degrade the organic matter in wastewater for food and flocculate to settle the pollutants. This study aimed to investigate the effect of food to microorganism (F/M) ratio and iron in a biological process using aerobic treatment. For this purpose, four aerobic tanks (A, B, C, D) were set up using activated sludge as the seed sludge, air pump as air diffuser to provide oxygen to the system, and three litres of synthetic medium as carbon source for each tank. A specific amount of iron (II) sulfate was added into tanks B, C, and D with the weight of 3 g, 6 g, and 9 g, respectively. Tank A act as a control, and no iron dosage was added. The F/M ratio for tanks A, B, C, and D were 0.8, 0.5, 0.4, and 0.3 mg BOD/mg MLVSS, respectively. The aerobic tanks were operated for 40 days in sequential batch mode and sampling was collected four times per week to observe the COD and MLVSS. This study has found that Tank D shows the best performance compared to all tanks with 84.71% COD removal efficiency and a fivefold increment of microorganism growth rate. These findings suggest that a relationship exists between the iron and F/M ratio to enhance the aerobic treatment process.

View
Thumbnail Image
Publication

Transformation from biofiltration unit to hybrid constructed wetland-microbial fuel cell: Improvement of wastewater treatment performance and energy recovery

2023-05-01 , Teoh T.P. , Koo C.J. , Ho Li Ngee , Wong Yee Shian , Nabilah Aminah Lutpi , Tan S.M. , Yap K.L. , Ong Soon An

This study aimed to compare the performance of biofiltration, constructed wetland, and constructed wetland microbial fuel cell (CW-MFC). The transformation from a biofiltration unit to a hybrid CW-MFC was demonstrated with the advantages of improvement of wastewater treatment while generating electricity simultaneously. The introduction of plants to the upper region of the bioreactor enhanced the DO level by 0.8 mg/L, ammonium removal by 5 %, and COD removal by 1 %. The integration of electrodes and external circuits stimulated the degradation rate of organic matter in the anodic region (1 % without aeration and 3 % with aeration) and produced 5.13 mW/m3 of maximum power density. Artificial aeration improved the nitrification efficiency by 38 % and further removed the residual COD to an efficiency of 99 %. The maximum power density was also increased by 3.2 times (16.71 mW/m3) with the aid of aeration. In treating higher organic loading wastewater (3M), the maximum power density showed a significant increment to 78.01 mW/m3 (4.6-fold) and the COD removal efficiency was 98 %. The ohmic overpotential dominated the proportion of total loss (67-91 %), which could be ascribed to the low ionic conductivity. The reduction in activation and concentration loss contributed to the lower internal resistance with the additional aeration and higher organic loading. Overall, the transformation from biofiltration to a hybrid CW-MFC system is worthwhile since the systems quite resemble while CW-MFC could improve the wastewater treatment as well as recover energy from the treated wastewater.

View
Thumbnail Image
Publication

Investigation of Biosand Filter (BSF) on the Treatment Performance of Industrial Latex Wastewater

2024-01-01 , Najihah Abdul Rashid , Abdul Latif Abdul Rani , Mohd Firdaus Omar , Zainol N.A. , Salwa Mohd Zaini Makhtar , A B Wahab M. , Nabilah Aminah Lutpi , Farrah Aini Dahalan

Biosand Filters (BSF) has great potential to improve the water quality. BSF is used extensively in the treatment of drinking water in rural areas because it is affordable, simple to use, and has a high removal efficiency. This study used actual latex effluent to examine the effectiveness of SBR. The growth of the biolayer in the BSF is also observed. This study analyzes consistent and stable results for COD, DO and NH4-N+. With removal performance ranging from 87 % to 99 %. DO value for BSF varied from lowest value of 1.5 mg/L to 8mg/L. Overall, the BSF was capable of producing treated water for water reclamation.

View
Thumbnail Image
Publication

Wastewater remediation and bioelectricity generation in dual chambered salt bridge microbial fuel cell: A mini-review

2024-09-01 , Iberahim N.I. , Nabilah Aminah Lutpi , Ho Li Ngee , Wong Y.S. , Ong Soon An , Farrah Aini Dahalan

The purpose of this article is to assess the feasibility analysis of microbial fuel cells (MFCs), particularly in the configuration of dual chamber salt bridge microbial fuel cell (DCSB-MFC), as a promising approach for simultaneous bioelectricity generation and wastewater remediation. The application of a salt bridge presents an economically viable alternative to the use of a proton exchange membrane, which is known for its high cost, in the construction of MFCs. This arrangement has been demonstrated to offer significant benefits in terms of enhancing the performance of new elements and evaluating operational parameters. However, it also encounters issues related to the total internal resistance (Rint) of the MFCs as well as power density (P). In addition, it has been found that traditional packing materials such activated carbon and gravel demonstrate poor permeability, internal resistance, and slow biofilm growth. Furthermore, there is a necessity to search for electrodes that possess high resistance to corrosion and are cost-effective to achieve optimal bioelectricity generation. Therefore, this article aims to emphasize the research areas that require attention. By addressing these areas, the actual implementation of this configuration can be brought closer to practical implementation.

View
Thumbnail Image
Publication

Biohydrogen production from palm oil mill effluent with Moringa Oleifera seeds as support carrier in attached growth system

2020-06-10 , Hamid W.Z.W.A. , Nabilah Aminah Lutpi , Wong Yee Shian , Ong Soon An , Malek M.A.

Biohydrogen production by dark fermentation is one of the attracting alternatives for renewable energy in worldwide. By employing immobilized cells, hydrogen production and cell density could be improved. This study aimed to investigate the efficiency of Moringa Oleifera Seeds (MOS) immobilized cells in enhancing the biohydrogen production using repeated batch fermentation under mesophilic condition, 37°C. The efficiency of MOS as support carrier, effect of the initial pH (5.0-7.0) and performance of raw and diluted Palm Oil Mill Effluent (POME) using MOS immobilized cells were investigated using anaerobic sludge as inoculums. The cumulative hydrogen production results were fitted into a modified Gompertz equation to find the maximum hydrogen production. MOS immobilized cells was more efficient in producing hydrogen compare to suspended cells (without MOS). The optimal pH obtained using MOS immobilized cells was found to be at pH 6 using raw POME with the maximum hydrogen production (Hm) of 122 mL, the maximum hydrogen production rate (Rm) of 39.0 mL/h, and 560 ppm of hydrogen concentration.

View
Thumbnail Image
Publication

Kinetic model discrimination on the biogas production in thermophilic co-digestion of sugarcane vinasse and water hyacinth

2022-08-01 , Audrey Chai Yee Chieh , Wong Yee Shian , Ong Soon An , Nabilah Aminah Lutpi , Sam Sung Ting , Kee W.C. , Eng K.M.

Co-digestion between sugarcane vinasse (Vn) and water hyacinth (WH) at various mixing ratios of 0:1, 1:0, 1:3, 3:1, and 1:1 was carried out under thermophilic conditions (55 °C) for 60 days. The effect of various mixing ratios on the pH changes, soluble chemical oxygen demand (sCOD) reduction, and cumulative biogas production was investigated. The first order, modified Gompertz, and logistic function kinetic models were selected to fit the experimental data. Model discrimination was conducted through the Akaike Information Criterion (AIC). The study revealed that co-digestion shows better performance compared to the mono-digestion of both substrates. Vn:WH mixing ratio 1:1 with inoculum to substrate ratio (ISR) of 0.38 g VSinoculum/g VSsubstrate is the most favorable ratio, achieving sCOD reduction efficiency and cumulative biogas production of 71.6% and 1229 mL, respectively. Model selection through AIC revealed that ratio 1:1 was best fitted to the logistic function kinetic model (R2 = 0.9897) with Ym and K values of 1232 mL and 31 mL/day, respectively.

View
Thumbnail Image
Publication

Effect of operating temperature in the anaerobic degradation of palm oil mill effluent: Process performance, microbial community, and biokinetic evaluation

2022-09-01 , Audrey Chai Yee Chieh , Wong Yee Shian , Ong Soon An , Nabilah Aminah Lutpi , Sam Sung Ting , Kee Wei Chin

This research paper presents the thermophilic anaerobic digestion (TAD) of palm oil mill effluent (POME), which is an extension of a previously conducted mesophilic anaerobic digestion (MAD) study. An anaerobic suspended growth closed bioreactor was operated at various hydraulic retention times (HRT) between 24 and 8 days. The effect of operating temperature on the performance, microbial identification, and biokinetic coefficients was evaluated. Performance was quantified by the production of biogas and the chemical oxygen demand (COD) reduction efficiency. Biogas production in TAD (64.56 L/day) was higher than MAD (46.76 L/day). A higher COD reduction efficiency was also achieved in TAD (90.90%) compared to MAD (89.66%). Other than that, more species of methanogenic bacteria were also identified in TAD through 16S rDNA. Furthermore, the modified Monod model implemented in the biokinetic evaluation revealed that higher values of maximum substrate utilization rate (rx,max) and maximum specific biomass growth rate (μmax) contributed to the better performance in TAD. The high rx,max value explains the higher COD reduction efficiency obtained in TAD. The critical retention time (θC) in TAD is also higher than MAD, making it less prone to the washout of active microbes when operating near low retention times. Additionally, TAD also achieved higher methane yield (YCH4) as opposed to MAD. The extension study concluded that the TAD of POME demonstrated improved performance in terms of biogas production and COD reduction when evaluated against the previously conducted MAD.

View
Thumbnail Image
Publication

Hydrogen sulfide removal from fermentative biohydrogen process: Effect of ZSM-5 zeolite loading

2024-03-01 , Asman M.K.A. , Nabilah Aminah Lutpi , Wong Y.S. , Hanif M.A. , Ong Soon An , Farrah Aini Dahalan , Nur Izzati Iberahim , Hamdzah M.

The production and consumption of biohydrogen is growing because it is a “green,” renewable energy that can be obtained in a relatively cost-effective manner through anaerobic digestion. Biohydrogen produced from biomass is a viable source of renewable energy; nevertheless, the presence of highly toxic and corrosive hydrogen sulfide (H2S) in the process can hinder the quality of biohydrogen production and limit its application in energy conversion equipment. Consequently, the goal of the research was to assess the feasibility of using ZSM-5 zeolite for H2S adsorption that function as activating agent to enhance biohydrogen quality under thermophilic conditions. The effect of ZMS-5 Zeolite loading (0.2–1.0 g) on biohydrogen production via dark fermentation from mixed fruit waste (MFW) was investigated using anaerobic sludge from a sewage treatment plant. The pH of the broth mixture was adjusted to 6.0, anaerobic conditions were created by purging it with nitrogen gas, and the temperature of the fermentative biohydrogen process was maintained at 60°C. Meanwhile, the H2S adsorption test was run at ambient temperature with flow rates (100 ml/min) and an H2S inlet concentration of 10000 ppm. The results indicate that the Z + H2S exhibit spectral lines corresponding to the S-H asymmetric stretching vibration of H2S at 2345.97 cm−1. The ideal adsorption capacity is at 0.8 g with yet, increasing the dosage amount of adsorbents, increases the time required for the adsorbent to achieve 90% saturation. The non-linear curve fitting demonstrated that the adsorption kinetics of all dosages used followed those of the Avrami kinetic model. This approach of using ZSM-5 zeolite for H2S removal provides an advantage in terms of minimizing environmental pollution and having great potential uses in industrial processes.

View
Thumbnail Image
Publication

Photocatalytic Degradation of Sugarcane Vinasse Using ZnO Photocatalyst: Operating Parameters, Kinetic Studies, Phytotoxicity Assessments, and Reusability

2022-02-01 , Kee W.C. , Wong Yee Shian , Ong Soon An , Nabilah Aminah Lutpi , Sam Sung Ting , Audrey Chai Yee Chieh , Eng K.M.

Abstract: Photocatalytic degradation performance is highly related to optimized operating parameters such as initial concentration, pH value, and catalyst dosage. In this study, the impact of various parameters on the photocatalytic degradation of anaerobically digested vinasse (AnVE) has been determined through decolourization and chemical oxygen demand (COD) reduction efficiency using zinc oxide (ZnO) photocatalyst. In this context, the application of photocatalytic degradation in treating sugarcane vinasse using ZnO is yet to be explored. The COD reduction efficiency and decolourization achieved 83.40% and 99.29%, respectively, under the conditions of 250 mg/L initial COD concentration, pH 10, and 2.0 g/L catalyst dosage. The phytotoxicity assessment was also conducted to determine the toxicity of AnVE before and after treatment using mung bean (Vigna radiata). The reduction of root length and the weight of mung bean indicated that the sugarcane vinasse contains enormous amounts of organic substances that affect the plant's growth. The toxicity reduction in the AnVE solution can be proved by UV–Vis absorption spectra. Furthermore, the catalyst recovery achieved 93% in the reusability test. However, the COD reduction efficiency and decolourization were reduced every cycle. It was due to the depletion of the active sites in the catalyst with the adsorption of organic molecules. Thus, it can be concluded that the photocatalytic degradation in the treatment of AnVE was effective in organic degradation, decolorization, toxicity reduction and can be reused after the recovery process. Graphical abstract: [Figure not available: see fulltext.].

View
Thumbnail Image
Publication

Caffeine-containing wastewater treatment and bioelectricity generation in up-flow constructed wetland-microbial fuel cell: Influence of caffeine concentration, operating conditions, toxicity assessment, and degradation pathway

2022-04-01 , Teoh T.P. , Ong Soon An , Ho Li Ngee , Wong Yee Shian , Nabilah Aminah Lutpi , Oon Y.L. , Tan S.M. , Ong Y.P. , Yap K.L.

This study explored the potential of caffeine being utilized as the fuel for the microbes to produce electrons for electricity generation in up-flow constructed wetland-microbial fuel cell (UFCW-MFC). The effect of caffeine concentration was investigated to identify the availability of UFCW-MFC in the conversion of caffeine to electrons for electricity production; and the effect of operating conditions (circuit connection, supplementary aeration, and plant) was studied to determine their significance in the treatment of caffeine containing wastewater. The UFCW-MFC achieved about 98% of decaffeination efficiency regardless of caffeine concentration; while a decrease of efficiency was observed when UFCW-MFC operated without supplementary aeration and plant (~93%). COD removal efficiency decreased correspondingly to the increase of caffeine concentration, which could be contributed by the higher concentration of caffeine and its intermediates. The degradation pathway of caffeine in UFCW-MFC was explored in this study. It was remarkable that ammonia was produced and converted to ammonium ions during caffeine catabolism. Supplementary aeration and macrophyte play a crucial role in removing excess caffeine, intermediates as well as accumulated ammonium ions. The toxicity assessment revealed that caffeine was degraded to less toxic products. The closed circuit connection not only contributed to electricity generation but also enhanced the caffeine and COD removal efficiency by 4.6 and 5.4% in the anaerobic region, respectively. The increase of voltage and maximum power density from phase I to phase IV indicated that caffeine could be converted to electrons by the anaerobes for electricity production.

View