Mohd. Mustafa Al Bakri Abdullah
Thumbnail Image
Preferred name
Mohd. Mustafa Al Bakri Abdullah
Official Name
Abdulah, Mohd. Mustafa Al Bakri
Alternative Name
Abdullah, M.M.A.
M.M.A. Abdullah
Mustafa Al Bakri, A. M.
Albakri Abdullah, M. M.
Main Affiliation
CeGeoGTech UniMAP
Scopus Author ID
53164519100

Research Output

Filters

1
Reset filters

Settings
Now showing 1 - 10 of 19
  • Publication
    Crumb rubber geopolymer mortar at elevated temperature exposure
    ( 2022)
    Ahmad Azrem Azmi
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Che Mohd Ruzaidi Ghazali
    ;
    Romisuhani Ahmad
    ;
    Ramadhansyah Putra Jaya
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohammad A. Almadani
    ;
    Wysłocki, Jerzy J.
    ;
    Agata Śliwa
    ;
    Andre Victor Sandu
    Low calcium fly ash is used as the main material in the mixture and the crumb rubber was used in replacing fine aggregates in geopolymer mortar. Sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) which were high alkaline solution were incorporated as the alkaline solution. The fly ash reacted with the alkaline solution forming alumino-silicate gel that binds the aggregate to produce a geopolymer mortar. The loading of crumb rubber in the fly ash based geopolymer mortar was set at 0%
  • Publication
    Ladle furnace slag replacement on the flexural strength of thin fly ash geopolymer
    ( 2020)
    Ng YONG-SING
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Ng HUI-TENG
    ;
    Ridho BAYUAJI
    This article reports the investigation on the effect of ladle furnace slag replacement on the flexural strength of thin fly ash-based geopolymer. The thin fly ash/slag geopolymers were prepared with the replacement of various percentages of ladle furnace slag (0%, 10%, 20%, 30% and 40%) into fly ash geopolymers with dimension of 160 mm × 40 mm × 10 mm. The thin geopolymerwas synthesised using 12M sodium hydroxide (NaOH) solution with solid-to-liquid (S/L) ratio of 2.5 and Na2SiO3 /NaOH ratio of 4.0. The curing temperature and time of samples were 60°C and 6 hours respectively. The mechanical properties of thin geopolymers was revealed using flexural test after 28 days. Several characterisation tools have been used including Scanning Electron Microscope (SEM) and X-Ray Diffraction (XRD) to correlate the flexural properties with the microstructure and phases of fly ash/slag geopolymers. Results obtained reported that a positive effect on flexural strength was observed with the increasing amount of slag. The thin fly ash geopolymers replaced with 40% of ladle furnace slag showed the highest flexural strength of 7.8 MPa. The rich CaO content in ladle furnace slag boosted the C-S-H gels formation which increased the flexural strength of thin geopolymers.
  • Publication
    Mechanical effects on different solid to liquid ratio of geopolymer filler in epoxy resin
    ( 2021)
    Mohammad Firdaus Abu Hashim
    ;
    Che Mohd Ruzaidi Ghazali
    ;
    Yusrina Mat Daud
    ;
    Meor Ahmad Faris bin Meor Ahmad Tajudin
    ;
    Saloma Hasyim
    ;
    Muhammad Taqiyuddin Lokman
    ;
    Farah Farhana Zainal
    ;
    Mohd. Mustafa Al Bakri Abdullah
    Geopolymer is formed from the alkali activation of materials rich in Si and Al content with the addition of a silicate solution to enhance the properties of the materials. This paper presents research on the mechanical properties of fly ash-based geopolymer filler in epoxy resin by varying different solid to liquid ratios using sodium hydroxide and sodium silicate as the alkaline activator. However, the common problem observed from the solid to liquid ratio is the influence of curing time and compressive strength of geopolymer to have the best mechanical property. The mix design for geopolymers of solid to liquid ratio is essential in developing the geopolymer’s mechanical strength. A series of epoxy filled with fly ash-based geopolymer materials with different solid to liquid ratio, which is prepared from 0.5 to 2.5 solid to liquid ratio of alkaline activator. The tensile strength and flexural strength of the epoxy filled with fly ash-based geopolymer materials is determined using Universal Testing Machine under tensile and flexural mode. It was found that the optimum solid to liquid ratio is 2.0, with the optimum tensile and flexural strength value. However, both the tensile and flexural properties of epoxy filled with fly ash-based geopolymer suddenly decrease at a 2.5 solid to liquid ratio. The strength is increasing with the increasing solid to liquid ratio sample of geopolymer filler content.
  • Publication
    Contribution of interfacial bonding towards geopolymers properties in geopolymers reinforced fibers: a review
    ( 2022)
    Muhd Hafizuddin Yazid
    ;
    Meor Ahmad Faris bin Meor Ahmad Tajudin
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Marcin Nabiałek
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Marwan Kheimi
    ;
    Andrei Victor Sandu
    ;
    Adam Rylski
    ;
    Bartłomiej Jeż
    There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.
  • Publication
    Flexural properties of thin fly ash geopolymers at elevated temperature
    ( 2021)
    Yong-Sing Ng
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Hui-Teng Ng
    ;
    Lynette Wei Ling Chan
    This paper reports on the flexural properties of thin fly ash geopolymers exposed to elevated temperature. The thin fly ash geopolymers (dimension = 160 mm × 40 mm × 10 mm) were synthesised using12M NaOH solution mixed with designed solidsto-liquids ratio of 1:2.5 and Na2SiO3/NaOH ratio of 1:4 and underwent heat treatment at different elevated temperature (300°C, 600°C, 900°C and 1150°C) after 28 days of curing. Flexural strength test was accessed to compare the flexural properties while X-Ray Diffraction (XRD) analysis was performed to determine the phase transformation of thin geopolymers at elevated temperature. Results showed that application of heat treatment boosted the flexural properties of thin fly ash geopolymers as the flexural strength increased from 6.5 MPa (room temperature) to 16.2 MPa (1150°C). XRD results showed that the presence of crystalline phases of albite and nepheline contributed to the increment in flexural strength.
  • Publication
    Assessment of geopolymer concrete for underwater concreting properties
    ( 2021)
    Fakhryna Hannanee Ahmad Zaidi
    ;
    Romisuhani Ahmad
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Wan Mastura Wan Ibrahim
    ;
    Ikmal Hakem Aziz
    ;
    Subaer Junaidi
    ;
    Salmabanu Luhar
    For ages, concrete has been used to construct underwater structures. Concrete laying underwater is a very complex procedure important to the success or failure of underwater projects. This paper elucidates the influence of alkali activator ratios on geopolymers for underwater concreting; focusing on the geopolymer concrete synthesized from fly ash and kaolin activated using sodium hydroxide and sodium silicate solutions. The geopolymer mixtures were designed to incorporate multiple alkali activator ratios to evaluate their effects on the resulting geopolymers’ properties. The fresh concrete was molded into 50 mm cubes in seawater using the tremie method and tested for its engineering properties at 7 and 28 days (curing). The control geopolymer and underwater geopolymers’ mechanical properties, such as compressive strength, water absorption density, and setting time were also determined. The differences between the control geopolymer and underwater geopolymer were determined using phase analysis and functional group analysis. The results show that the geopolymer samples were optimally strengthened at a 2.5 alkali activator ratio, and the mechanical properties of the control geopolymer exceeded that of the underwater geopolymer. However, the underwater geopolymer was determined to be suitable for use as underwater concreting material as it retains 70% strength of the control geopolymer.
  • Publication
    Formulation, mechanical properties and phase analysis of fly ash geopolymer with ladle furnace slag replacement
    ( 2021)
    Ng Hui-Teng
    ;
    Heah Cheng Yong
    ;
    Kong Ern Hun
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Liew Yun Ming
    ;
    Hasniyati Md Razi
    ;
    Ng Yong-Sing
    This paper presents the formulation of fly ash (FA) geopolymer and the incorporation of ladle furnace slag (LFS) as a replacement to FA in geopolymer formation. The formulation of the LFS replacement was set at 10–40 wt.%. The geopolymer was formed by mixing FA and LFS with a sodium-based alkali activator. The FA geopolymer had a compressive strength of 38.9 MPa with the optimum formulation of 8 M NaOH concentration, AS/AA ratio of 3, and AA ratio of 1.5. The compressive strength was affected more significantly by the amorphous content. The most influential factors affecting the properties of FA geopolymer were: AS/AA ratio > AA ratio > NaOH concentration. Replacing LFS led to very little (4.1%) increment in the compressive strength. The LFS had little contribution in supplying Si, Al and Ca for the formation of the N-A-S-H and C-A-S-H network. But LFS acted as a filler and improved the compactness of the FA geopolymer. The mechanical performance of FA/LFS geopolymer was not governed by the amorphous content like the FA geopolymer, as LFS addition contributed to increasing crystalline content. New crystalline phases of calcite and CSH due to the addition of LFS helped to retain the compressive strength of FA geopolymer. Nevertheless, the outcome of the study proved that LFS can be blended with FA to produce geopolymers without severe deterioration in mechanical strength. LFS can be potentially added in geopolymers as filler to produce geopolymer mortar.
  • Publication
    Evaluation on the mechanical properties of Ground Granulated Blast Slag (GGBS) and fly ash stabilized soil via geopolymer process
    ( 2021)
    Syafiadi Rizki Abdila
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Romisuhani Ahmad
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Małgorzata Rychta
    ;
    Izabela Wnuk
    ;
    Marcin Nabiałek
    ;
    Krzysztof Muskalski
    ;
    Muhammad Faheem Mohd. Tahir
    ;
    Muhammad Syafwandi
    ;
    Marek Isradi
    This study intended to address the problem of damaged (collapsed, cracked and decreased soil strength) road pavement structure built on clay soil due to clay soil properties such as low shear strength, high soil compressibility, low soil permeability, low soil strength, and high soil plasticity. Previous research reported that ground granulated blast slag (GGBS) and fly ash can be used for clay soil stabilizations, but the results of past research indicate that the road pavement construction standards remained unfulfilled, especially in terms of clay’s subgrade soil. Due to this reason, this study is carried out to further investigate soil stabilization using GGBS and fly ash-based geopolymer processes. This study investigates the effects of GGBS and ratios of fly ash (solid) to alkaline activator (liquid) of 1:1, 1.5:1, 2:1, 2.5:1, and 3:1, cured for 1 and 7 days. The molarity of sodium hydroxide (NaOH) and the ratio of sodium silicate (Na2SiO3) to sodium hydroxide (NaOH) was fixed at 10 molar and 2.0 weight ratio. The mechanical properties of the soil stabilization based geopolymer process were tested using an unconfined compression test, while the characterization of soil stabilization was investigated using the plastic limit test, liquid limit test, scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). The results showed that the highest strength obtained was 3.15 MPA with a GGBS to alkaline activator ratio of 1.5 and Na2SiO3 to NaOH ratio of 2.0 at 7 days curing time. These findings are useful in enhancing knowledge in the field of soil stabilization-based geopolymer, especially for applications in pavement construction. In addition, it can be used as a reference for academicians, civil engineers, and geotechnical engineers.
  • Publication
    Potential of fly ash geopolymer concrete as repairing and retrofitting solutions for marine infrastructure: A review
    ( 2024)
    Noor Fifinatasha Shahedan
    ;
    Tony Hadibarata
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Muhammad Noor Hazwan Jusoh
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Ismallianto Isia
    ;
    Ana Armada Bras
    ;
    Aissa Bouaissi
    ;
    Filbert Hilman Juwono
    Corrosion in maritime infrastructure, particularly in reinforced concrete, has emerged as a significant cause for concern due to the presence of chloride ions in seawater. To address this challenge, geopolymer concrete has been proposed as a viable solution for retrofitting and restoring marine structures. This review paper explores the potential application of fly ash geopolymer concrete in marine infrastructure restoration. Fly ash's properties make it ideal for marine infrastructure restoration. Its high levels of amorphous silica and alumina enable geopolymerization, forming a strong binder resistant to chloride corrosion. Its fine, spherical particles enhance concrete workability and density, improving mechanical strength and impermeability. This geopolymer binder offers excellent resistance to corrosion from chloride ions commonly found in seawater, making fly ash geopolymer concrete highly suitable for marine applications. Overall, fly ash's chemical composition and physical traits offer resilience and sustainability in restoring marine infrastructure, ensuring long-term durability against corrosion. This review paper explores the potential application of fly ash geopolymer concrete in marine infrastructure restoration. By examining the primary forms of damage and mechanisms underlying concrete degradation in marine settings, this study highlights the durability and sustainability of geopolymer concrete compared to traditional concrete. Additionally, it discusses current solutions for repairing and retrofitting concrete in marine environments, emphasizing the promising characteristics of geopolymer concrete for integration into such structures. Through this analysis, innovative and environmentally conscious approaches are introduced for addressing corrosion-related challenges in the maritime industry, offering a resilient solution for the construction of enduring marine structures. Finally, recommendations for further research on the application of fly ash geopolymer concrete in marine infrastructure restoration are presented.
  • Publication
    Potential of soil stabilization using Ground Granulated Blast Furnace Slag (GGBFS) and fly ash via geopolymerization method: a review
    ( 2022)
    Syafiadi Rizki Abdila
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Romisuhani Ahmad
    ;
    Dumitru Doru Burduhos Nergis
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd Firdaus Omar
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    Geopolymers, or also known as alkali-activated binders, have recently emerged as a viable alternative to conventional binders (cement) for soil stabilization. Geopolymers employ alkaline activation of industrial waste to create cementitious products inside treated soils, increasing the clayey soils’ mechanical and physical qualities. This paper aims to review the utilization of fly ash and ground granulated blast furnace slag (GGBFS)-based geopolymers for soil stabilization by enhancing strength. Previous research only used one type of precursor: fly ash or GGBFS, but the strength value obtained did not meet the ASTM D 4609 (<0.8 Mpa) standard required for soil-stabilizing criteria of road construction applications. This current research focused on the combination of two types of precursors, which are fly ash and GGBFS. The findings of an unconfined compressive strength (UCS) test on stabilized soil samples were discussed. Finally, the paper concludes that GGBFS and fly-ash-based geo-polymers for soil stabilization techniques can be successfully used as a binder for soil stabilization. However, additional research is required to meet the requirement of ASTM D 4609 standard in road construction applications, particularly in subgrade layers.