Mohd. Mustafa Al Bakri Abdullah

Mohd. Mustafa Al Bakri Abdullah

Preferred name

Mohd. Mustafa Al Bakri Abdullah

Official Name

Abdulah, Mohd. Mustafa Al Bakri

Alternative Name

Abdullah, M.M.A.

M.M.A. Abdullah

Mustafa Al Bakri, A. M.

Albakri Abdullah, M. M.

Main Affiliation

Universiti Malaysia Perlis

CeGeoGTech UniMAP

Scopus Author ID

53164519100

Now showing 1 - 10 of 12

The influence of heat treatment on the magnetic properties of the alloy Fe₆₂Co₁₀Y₈B₂₀ produced by the injection suction casting method

(Jagiellonian University, 2020)
M. Talar
;
J. Gondro
;
P. Vizureanu
;
Mohd. Mustafa Al Bakri Abdullah
;
K. Błoch

The paper presents studies of annealing effect on the magnetic properties of the bulk Fe62Co10Y8B20alloy in the form of rods. The thermal treatment was performed at the temperature well below the crystallization temperature. Structure, revealed by X-ray diffraction and Mössbauer spectroscopy and magnetic properties in high magnetic fields in the Fe62Co10Y8B20alloy after fabricated and after the annealing were studied. We have stated that the investigated alloy was fully amorphous. It is due to the stress relieving of the sample. Using a vibrating sample magnetometer the magnetization in high magnetic fields was studied. For both the sample after solidification and after heat treatment, the magnetization process in the area called "the approach to ferromagnetic saturation" is affected by free volumes. In addition, the heat treatment improved the magnetic properties and increased the packing density of atoms.
Role of sintering temperature in production of nepheline ceramics-based geopolymer with addition of ultra-high molecular weight polyethylene

(MDPI, 2021)
Romisuhani Ahmad
;
Mohd. Mustafa Al Bakri Abdullah
;
Jitrin Chaiprapa
;
Kamarudin Hussin
;
Wan Mastura Wan Ibrahim
;
Fakhryna Hannanee Ahmad Zaidi
;
Jerzy J. Wysłocki
;
Katarzyna Błoch
;
Marcin Nabiałek

The primary motivation of developing ceramic materials using geopolymer method is to minimize the reliance on high sintering temperatures. The ultra-high molecular weight polyethylene (UHMWPE) was added as binder and reinforces the nepheline ceramics based geopolymer. The samples were sintered at 900 °C, 1000 °C, 1100 °C, and 1200 °C to elucidate the influence of sintering on the physical and microstructural properties. The results indicated that a maximum flexural strength of 92 MPa is attainable once the samples are used to be sintered at 1200 °C. It was also determined that the density, porosity, volumetric shrinkage, and water absorption of the samples also affected by the sintering due to the change of microstructure and crystallinity. The IR spectra reveal that the band at around 1400 cm−1 becomes weak, indicating that sodium carbonate decomposed and began to react with the silica and alumina released from gels to form nepheline phases. The sintering process influence in the development of the final microstructure thus improving the properties of the ceramic materials.

3 19
Properties of a new insulation material glass bubble in geopolymer concrete

( 2021)
Noor Fifinatasha Shahedan
;
Mohd. Mustafa Al Bakri Abdullah
;
Norsuria Mahmed
;
Andri Kusbiantoro
;
Sam Tammas-Williams
;
Petrică Vizureanu
;
Jerzy J. Wysłocki
;
Ikmal Hakem Aziz
;
Katarzyna Błoch
;
Marcin Nabiałek

This paper details analytical research results into a novel geopolymer concrete embedded with glass bubble as its thermal insulating material, fly ash as its precursor material, and a combination of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) as its alkaline activator to form a geopolymer system. The workability, density, compressive strength (per curing days), and water absorption of the sample loaded at 10% glass bubble (loading level determined to satisfy the minimum strength requirement of a load-bearing structure) were 70 mm, 2165 kg/m3, 52.58 MPa (28 days), 54.92 MPa (60 days), and 65.25 MPa (90 days), and 3.73 %, respectively. The thermal conductivity for geopolymer concrete decreased from 1.47 to 1.19 W/mK, while the thermal diffusivity decreased from 1.88 to 1.02 mm2/s due to increased specific heat from 0.96 to 1.73 MJ/m3K. The improved physicomechanical and thermal (insulating) properties resulting from embedding a glass bubble as an insulating material into geopolymer concrete resulted in a viable composite for use in the construction industry.

4 11
Microstructure evolution of Ag/TiO₂ thin film

( 2021)
Dewi Suriyani Che Halin
;
Kamrosni Abdul Razak
;
Mohd Arif Anuar Mohd Salleh
;
Mohd Izrul Izwan Ramli
;
Mohd. Mustafa Al Bakri Abdullah
;
Ayu Wazira Azhari
;
Kazuhiro Nogita
;
Hideyuki Yasuda
;
Marcin Nabiałek
;
Jerzy J. Wysłocki

Ag/TiO₂ thin films were prepared using the sol-gel spin coating method. The microstructural growth behaviors of the prepared Ag/TiO₂ thin films were elucidated using real-time synchrotron radiation imaging, its structure was determined using grazing incidence X-ray diffraction (GIXRD), its morphology was imaged using the field emission scanning electron microscopy (FESEM), and its surface topography was examined using the atomic force microscope (AFM) in contact mode. The cubical shape was detected and identified as Ag, while the anatase, TiO₂ thin film resembled a porous ring-like structure. It was found that each ring that coalesced and formed channels occurred at a low annealing temperature of 280 °C. The energy dispersive X-ray (EDX) result revealed a small amount of Ag presence in the Ag/TiO₂ thin films. From the in-situ synchrotron radiation imaging, it was observed that as the annealing time increased, the growth of Ag/TiO₂ also increased in terms of area and the number of junctions. The growth rate of Ag/TiO₂ at 600 s was 47.26 µm2/s, and after 1200 s it decreased to 11.50 µm2/s and 11.55 µm2/s at 1800 s. Prolonged annealing will further decrease the growth rate to 5.94 µm2/s, 4.12 µm2/s and 4.86 µm2/s at 2400 s, 3000 s and 3600 s, respectively.

3 17
The effects of various concentrations of NaOH on the Inter-Particle Gelation of a Fly Ash Geopolymer Aggregate

( 2021)
Alida Abdullah
;
Kamarudin Hussin
;
Mohd. Mustafa Al Bakri Abdullah
;
Zarina Yahya
;
Wojciech Sochacki
;
Rafiza Abdul Razak
;
Katarzyna Błoch
;
Hamzah Fansuri

Aggregates can be categorized into natural and artificial aggregates. Preserving natural resources is crucial to ensuring the constant supply of natural aggregates. In order to preserve these natural resources, the production of artificial aggregates is beginning to gain the attention of researchers worldwide. One of the methods involves using geopolymer technology. On this basis, this current research focuses on the inter-particle effect on the properties of fly ash geopolymer aggregates with different molarities of sodium hydroxide (NaOH). The effects of synthesis parameters (6, 8, 10, 12, and 14 M) on the mechanical and microstructural properties of the fly ash geopolymer aggregate were studied. The fly ash geopolymer aggregate was palletized manually by using a hand to form a sphere-shaped aggregate where the ratio of NaOH/Na2SiO3 used was constant at 2.5. The results indicated that the NaOH molarity has a significant effect on the impact strength of a fly ash geopolymer aggregate. The highest aggregate impact value (AIV) was obtained for samples with 6 M NaOH molarity (26.95%), indicating the lowest strength among other molarities studied and the lowest density of 2150 kg/m3. The low concentration of sodium hydroxide in the alkali activator solution resulted in the dissolution of fly ash being limited; thus, the inter-particle volume cannot be fully filled by the precipitated gels.

7 10
Characterisation at the bonding zone between fly ash based Geopolymer Repair Materials (GRM) and Ordinary Portland Cement Concrete (OPCC)

( 2020)
Warid Wazien Ahmad Zailani
;
Mohd. Mustafa Al Bakri Abdullah
;
Mohd Fadzil Arshad
;
Rafiza Abd Razak
;
Muhammad Faheem Mohd. Tahir
;
Remy Rozainy Mohd Arif Zainol
;
Marcin Nabialek
;
Andrei Victor Sandu
;
Jerzy J. Wysłocki
;
Katarzyna Błoch

In recent years, research and development of geopolymers has gained significant interest in the fields of repairs and restoration. This paper investigates the application of a geopolymer as a repair material by implementation of high-calcium fly ash (FA) as a main precursor, activated by a sodium hydroxide and sodium silicate solution. Three methods of concrete substrate surface preparation were cast and patched: as-cast against ordinary Portland cement concrete (OPCC), with drilled holes, wire-brushed, and left as-cast against the OPCC grade 30. This study indicated that FA-based geopolymer repair materials (GRMs) possessed very high bonding strength at early stages and that the behavior was not affected significantly by high surface treatment roughness. In addition, the investigations using scanning electron microscopy (SEM) and energy-dispersive X-ray (EDX) spectroscopy have revealed that the geopolymer repair material became chemically bonded to the OPC concrete substrate, due to the formation of a C–A–S–H gel. Fundamentally, the geopolymer network is composed of tetrahedral anions (SiO4)4− and (AlO4)5− sharing the oxygen, which requires positive ions such as Na+, K+, Li+, Ca2+, Na+, Ba2+, NH4+, and H3O+. The availability of calcium hydroxide (Ca(OH)2) at the surface of the OPCC substrate, which was rich in calcium ions (Ca2+), reacted with the geopolymer; this compensated the electron vacancies of the framework cavities at the bonding zone between the GRM and the OPCC substrate.

1 18
The effect of thermal annealing on the microstructure and mechanical properties of Sn-0.7Cu-xZn Solder Joint

( 2021)
Mohd Izrul Izwan Ramli
;
Mohd Arif Anuar Mohd Salleh
;
Rita Mohd Said
;
Marcin Nabiałek
;
Mohd. Mustafa Al Bakri Abdullah
;
Norainiza Saud
;
Dewi Suriyani Che Halin

The microstructural properties of a Pb-free solder joint significantly affect its mechanical behaviours. This paper details a systematic study of the effect of the annealing process on the microstructure and shear strength of a Zn-added Sn-0.7Cu solder joint. The results indicated that the IMC layer’s thickness at the solder/Cu interface increases with annealing time. The interfacial IMC layer of the Sn-0.7Cu solder joint gradually thickened with increasing annealing time and annealing temperature, while the interfacial IMC layer’s morphology changed from scallop-type to layer-type after the annealing process. However, the addition of 1.0 wt.% and 1.5 wt.% Zn in the Sn-0.7Cu effectively altered the interfacial IMC phase to Cu-Zn and suppressed the growth of Cu3Sn during the annealing process. The single-lap shear tests results confirmed that the addition of Zn decreased the shear strength of Sn-0.7Cu. The interfacial IMC of the Cu6Sn5 phase in Sn-0.7Cu changed to Cu-Zn due to the addition of Zn. The shear fractures in the annealed solder joint were ductile within the bulk solder instead of the interfacial IMC layer. Increased annealing time resulted in the increased presence of the Cu-Zn phase, which decreased the hardness and shear strength of the Sn-0.7Cu solder joint.

3 15
Optimisation of shrinkage and strength on thick plate part using recycled LDPE materials

( 2021)
Norshahira Roslan
;
Shayfull Zamree Abd. Rahim
;
Abdellah El-hadj Abdellah
;
Mohd. Mustafa Al Bakri Abdullah
;
Katarzyna Błoch
;
Paweł Pietrusiewicz
;
Marcin Nabiałek
;
Janusz Szmidla
;
Dariusz Kwiatkowski
;
Joel Oliveira Correia Vasco
;
Mohd. Nasir Mat Saad
;
Mohd Fathullah Ghazli@Ghazali

Achieving good quality of products from plastic injection moulding processes is very challenging, since the process comprises many affecting parameters. Common defects such as warpage are hard to avoid, and the defective parts will eventually go to waste, leading to unnecessary costs to the manufacturer. The use of recycled material from postindustrial waste has been studied by a few researchers. However, the application of an optimisation method by which to optimise processing parameters to mould parts using recycled materials remains lacking. In this study, Response Surface Methodology (RSM) and Particle Swarm Optimisation (PSO) methods were conducted on thick plate parts moulded using virgin and recycled low-density polyethylene (LDPE) materials (100:0, 70:30, 60:40 and 50:50; virgin to recycle material ratios) to find the optimal input parameters for each of the material ratios. Shrinkage in the x and y directions increased in correlation with the recycled ratio, compared to virgin material. Meanwhile, the tensile strength of the thick plate part continued to decrease when the recycled ratio increased. R30 (70:30) had the optimum shrinkage in the x direction with respect to R0 (100:0) material where the shrinkage increased by 24.49% (RSM) and 33.20% (PSO). On the other hand, the shrinkage in the y direction for R30 material increased by 4.48% (RSM) and decreased by 2.67% (PSO), while the tensile strength of R30 (70:30) material decreased by 0.51% (RSM) and 2.68% (PSO) as compared to R0 (100:0) material. Validation tests indicated that the optimal setting of processing parameter suggested by PSO and RSM for R0 (100:0), R30 (70:30), R40 (60:40) and R50 (50:50) was less than 10%.

1 60
Potential of new sustainable Green Geopolymer Metal Composite (GGMC) material as mould insert for Rapid Tooling (RT) in injection moulding process

(MDPI, 2023)
Allice Tan Mun Yin
;
Shayfull Zamree Abd. Rahim
;
Mohd. Mustafa Al Bakri Abdullah
;
Marcin Nabialek
;
Abdellah El-hadj Abdellah
;
Allan Rennie
;
Aurel Mihail Titu
;
Muhammad Faheem Mohd. Tahir

The investigation of mould inserts in the injection moulding process using metal epoxy composite (MEC) with pure metal filler particles is gaining popularity among researchers. Therefore, to attain zero emissions, the idea of recycling metal waste from industries and workshops must be investigated (waste free) because metal recycling conserves natural resources while requiring less energy to manufacture new products than virgin raw materials would. The utilisation of metal scrap for rapid tooling (RT) in the injection moulding industry is a fascinating and potentially viable approach. On the other hand, epoxy that can endure high temperatures (>220 °C) is challenging to find and expensive. Meanwhile, industrial scrap from coal-fired power plants can be a precursor to creating geopolymer materials with desired physical and mechanical qualities for RT applications. One intriguing attribute of geopolymer is its ability to endure temperatures up to 1000 °C. Nonetheless, geopolymer has a higher compressive strength of 60–80 MPa (8700–11,600 psi) than epoxy (68.95 MPa) (10,000 psi). Aside from its low cost, geopolymer offers superior resilience to harsh environments and high compressive and flexural strength. This research aims to investigate the possibility of generating a new sustainable material by integrating several types of metals in green geopolymer metal composite (GGMC) mould inserts for RT in the injection moulding process. It is necessary to examine and investigate the optimal formulation of GGMC as mould inserts for RT in the injection moulding process. With less expensive and more ecologically friendly components, the GGMC is expected to be a superior choice as a mould insert for RT. This research substantially impacts environmental preservation, cost reduction, and maintaining and sustaining the metal waste management system. As a result of the lower cost of recycled metals, sectors such as mould-making and machining will profit the most.

27 2
The Effects of Various Concentrations of NaOH on the Inter-Particle Gelation of a Fly Ash Geopolymer Aggregate

( 2021)
Alida Abdullah
;
Kamarudin Hussin
;
Mohd. Mustafa Al Bakri Abdullah
;
Zarina Yahya
;
Wojciech Sochacki
;
Katarzyna Błoch
;
Hamzah Fansuri
;
Rafiza Abdul Razak

Aggregates can be categorized into natural and artificial aggregates. Preserving natural resources is crucial to ensuring the constant supply of natural aggregates. In order to preserve these natural resources, the production of artificial aggregates is beginning to gain the attention of researchers worldwide. One of the methods involves using geopolymer technology. On this basis, this current research focuses on the inter-particle effect on the properties of fly ash geopolymer aggregates with different molarities of sodium hydroxide (NaOH). The effects of synthesis parameters (6, 8, 10, 12, and 14 M) on the mechanical and microstructural properties of the fly ash geopolymer aggregate were studied. The fly ash geopolymer aggregate was palletized manually by using a hand to form a sphere-shaped aggregate where the ratio of NaOH/Na2SiO3 used was constant at 2.5. The results indicated that the NaOH molarity has a significant effect on the impact strength of a fly ash geopolymer aggregate. The highest aggregate impact value (AIV) was obtained for samples with 6 M NaOH molarity (26.95%), indicating the lowest strength among other molarities studied and the lowest density of 2150 kg/m3. The low concentration of sodium hydroxide in the alkali activator solution resulted in the dissolution of fly ash being limited; thus, the inter-particle volume cannot be fully filled by the precipitated gels.

2 16

Mohd. Mustafa Al Bakri Abdullah

Filters

Settings

Sort By

Results per page

Options

Mohd. Mustafa Al Bakri Abdullah

Filters

Settings

Sort By

Results per page