Safizan Shaari
Thumbnail Image
Preferred name
Safizan Shaari
Official Name
Safizan, Shaari
Alternative Name
Shaari, Safizan
Shaari, S.
Main Affiliation
Scopus Author ID
55807708700
Researcher ID
AAR-5562-2021

Research Output

Filters

10 1
2
10
Reset filters

Settings
Now showing 1 - 10 of 10
  • Publication
    Modification of photoanode surface structure via image analysis on organic polymer material based for dye-sensitized solar cell (DSSC) applications
    ( 2021-12)
    N. Rosli
    ;
    Norhayati Sabani
    ;
    MF Ahmad
    ;
    Mohd. Azarulsani Md. Azidin
    ;
    Nurjuliana Juhari
    ;
    NF Zakaria
    ;
    Mohd Natashah Norizan
    ;
    Safizan Shaari
    In this study, the experiment on the modification of the photoanode with organic polymer material as copolymer template for dye-sensitized solar cell (DSSC) applications has been conducted. The two organic copolymer templates are polystyrene sphere (PS) and poly[2- methoxy-5(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV). The modification photoanodes were made using Dr. Blade’s method. These organic copolymer templates were added to improve the surface of the mesoporous titanium dioxide (TiO₂) layer, which is used as the main component in DSSC photoanode. The unmodified TiO₂ photoanode has poor aggregation and porosity of TiO₂. The addition of either MEH-PPV or PS sphere to the photoanode layer was found to affect the surface of mesoporous TiO₂ in terms of porosity, particle size distribution and shape. The analysis of the TiO2 modification was conducted using an image analysis processing method via a 2D scanning electron microscope (SEM) image. The image analysis processing method used was the ImageJ program. The DSSC of modified photoanode is fabricated using metal complex dye, Ruthenium (N719) dye. The data collected from the ImageJ program showed that by adding organic copolymer templates into TiO₂, the porosity of TiO₂ decreased from 45 % to 42 %. From the photovoltaic analysis obtained, the J-V characteristic is recorded with the photoanode of TiO₂ mixed with 1.00 wt% MEH-PPV gave the highest efficiency, which is 0.01 % with the following parameters – Voc = 0.43 V, Jsc = 0.17 mA/cm2 and FF = 0.20. Meanwhile, the photoanode of TiO₂ mixed with 0.50 wt% PS sphere gave the highest efficiency which is 0.08 % with the following parameters – Voc = 0.39 V, Jsc = 0.86 mA/cm2 and FF = 0.25.
  • Publication
    Optimization of MEH-PPV based single and double-layer TOLED structure by numerical simulation
    ( 2021-12)
    T. Kersenan
    ;
    Nor Farhani Zakaria
    ;
    Safizan Shaari
    ;
    Norhayati Sabani
    ;
    Nurjuliana Juhari
    ;
    Meor Ahmad Faris bin Meor Ahmad Tajudin
    ;
    A.F.A Rahim
    In this work, we simulated and characterized Poly [2-methoxy-5-(2’-ethylhexyloxy)-1, 4-phenylene vinylene] (MEH-PPV) based single and double-layer TOLED by using Silvaco ATLAS device simulator to achieve prominent values of electrical and optical properties of the device. MEH-PPV were used as the emitting layer (EML) in the single-layer, while addition of Poly [(3,4-ethylene dioxythiophene)-poly(styrene sulfonate)] (PEDOT-PSS) as the electron transport layer (ETL) were conducted in double-layer TOLED simulation. The EML and ETL thickness in both structures were varied between 10 – 150 nm, respectively, to observe and understand the underlying physics of the relation in the layer thickness to the electrical and optical characteristics. Furthermore, variation of the EML/ETL thickness ratio from 1:1 to 5:1 (with thickness in between 10 to 50 nm) had also been conducted. From this work, it is understood that the thickness of the EML layer plays the most important role in TOLED, and by balancing the carrier injections and recombination rate in appropriate EML/ETL thickness ratio, the electrical and optical properties can be improved. By optimizing the EML/ETL thickness and thickness ratio, an optimal forward current of 1.41 mA and luminescent power of 1.93e-18 W/μm has been achieved with both MEH-PPV and PEDOT-PSS layer thickness of 10 nm (1:1 ratio), respectively. The results from this work will assist the improvement of TOLED device to be implemented widely in low power and transparent electronic appliances.
  • Publication
    Temperature effects on electrical and structural properties of MEH-PPV/PEIE OLED Device
    ( 2020-06-16)
    Nurul Afiqah Nor Ismail
    ;
    Safizan Shaari
    ;
    Mohd Fairus Ahmad
    ;
    Norhayati Sabani
    ;
    Nurjuliana Juhari
    ;
    Nor Farhani Zakaria
    This paper explores the performance of configuration ITO/MEH-PPV/PEIE/Al OLED under the variations of temperature. The MEH-PPV and MEH-PPV/PEIE thin film were deposited on ITO substrates using spin coating technique with fixed spin speed of 3000 rpm and baked at low temperature ranging from 90 °C to 180 °C, respectively. The surface roughness values for MEH-PPV and MEH-PPV/PEIE films were analysed using AFM with 5 μm ' 5 μm scanning area. The roughness of MEH-PPV thin films were reduced from 2.825 nm to 1.625 nm when temperature increased. Contrary to MEH-PPV/PEIE films where the roughness increased linearly up to 3.397 nm when the temperature increased. The maximum absorption peak spectrum obtained from UV-Visible (UV-Vis) was found at 500 nm to 510 nm when baked temperature were varied. Furthermore, the turn on voltage from J-V characteristics gives no specific pattern across different temperature and agreed with the trend of surface roughness values. The turn-on voltage at T = 150 °C gives the lowest value of 3 V. Overall, the variations of low temperature gives an effects on structural and electrical properties of this OLED configuration.
  • Publication
    Modification of Photoanode Surface Structure via Image Analysis on Organic Polymer Material based for Dye-Sensitized Solar Cell (DSSC) Applications
    ( 2021-12-01)
    Rosli N.
    ;
    Norhayati Sabani
    ;
    Mohd Fairus Ahmad
    ;
    Azidin M.A.M.
    ;
    Nurjuliana Juhari
    ;
    Zakaria N.F.
    ;
    Mohd Natashah Norizan
    ;
    Safizan Shaari
    In this study, the experiment on the modification of the photoanode with organic polymer material as copolymer template for dye-sensitized solar cell (DSSC) applications has been conducted. The two organic copolymer templates are polystyrene sphere (PS) and poly[2-methoxy-5(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV). The modification photoanodes were made using Dr. Blade’s method. These organic copolymer templates were added to improve the surface of the mesoporous titanium dioxide (TiO2) layer, which is used as the main component in DSSC photoanode. The unmodified TiO2 photoanode has poor aggregation and porosity of TiO2. The addition of either MEH-PPV or PS sphere to the photoanode layer was found to affect the surface of mesoporous TiO2 in terms of porosity, particle size distribution and shape. The analysis of the TiO2 modification was conducted using an image analysis processing method via a 2D scanning electron microscope (SEM) image. The image analysis processing method used was the ImageJ program. The DSSC of modified photoanode is fabricated using metal complex dye, Ruthenium (N719) dye. The data collected from the ImageJ program showed that by adding organic copolymer templates into TiO2, the porosity of TiO2 decreased from 45 % to 42 %. From the photovoltaic analysis obtained, the J-V characteristic is recorded with the photoanode of TiO2 mixed with 1.00 wt% MEH-PPV gave the highest efficiency, which is 0.01 % with the following parameters – Voc = 0.43 V, Jsc = 0.17 mA/cm2 and FF = 0.20. Meanwhile, the photoanode of TiO2 mixed with 0.50 wt% PS sphere gave the highest efficiency which is 0.08 % with the following parameters – Voc = 0.39 V, Jsc = 0.86 mA/cm2 and FF = 0.25.
  • Publication
    The effect of solvents on the performance of organic light-emitting diodes
    ( 2020-01-08)
    Ismail N.A.N.
    ;
    Safizan Shaari
    ;
    Juhari N.
    ;
    Norhayati Sabani
    ;
    Mohd Fairus Ahmad
    ;
    Zakaria N.F.
    In this paper, we investigate the solvent effect on the performance of surface roughness, absorption spectrum of MEH-PPV thin films and J-V characteristics for MEH-PPV OLED device. The 5 mg emissive layer of poly [2-methoxy-5(2' -ethylhexyloxy)-1, 4-phenylenevinylene), MEH-PPV was diluted with 1ml toluene and 1 ml different mixture of solvent (80% toluene+20 % chloroform) which gives the concentration of 5 mgml-1 respectively. The surface roughness of MEH-PPV film was reduced to 0.3 nm and the red-shifted maximum peak wavelength value were obtained when mixture solvent was used. However, J-V gives higher turn on voltage ∼17 V for the device used mixture solvent compared to device prepared by toluene solvent. Apparently, the two different combination of aromatic and non-aromatic solvent significantly gives an effect on thin films properties and electrical properties of MEH-PPV OLED device.
  • Publication
    The structural and electrical characterization of PEDOT:PSS/MEH-PPV doped with PEIE OLED fabricated using spin coating technique
    ( 2020-01-08)
    Juhari N.
    ;
    Shukri N.I.A.
    ;
    Norhayati Sabani
    ;
    Safizan Shaari
    ;
    Mohd Fairus Ahmad
    ;
    Nor Farhani Zakaria
    This paper investigates the performance of the uniformity and absorption spectrum of MEHPPV+PEIE thin films also the electrical properties for configuration of ITO/PEDOT: PSS/MEH+PEIE/Al. The sample used 0.5 wt % of PEDOT: PSS solution while 5 mgml-1 concentration of MEH-PPV solution was doped with four different concentrations of PEIE with values of 0.1 wt%, 0.3 wt%, 0.5 wt% and 0.7 wt% respectively. The untreated PEDOT: PSS and MEH-PPV+PEIE was deposited using spin coating technique at a fixed spun speed of 3000 rpm to obtain smooth surface roughness thin film. The root mean square (RMS) value, absorption spectrum and current density (A/cm-2) of the PEDOT: PSS and MEH-PPV+PEIE films were analyzed using Atomic Force Microscope (AFM), UV-Visible (UV-Vis) Spectrophotometer and Semiconductor Parametric Analyzer (SPA), respectively. The surface roughness of the films were linearly increased when the dopant concentration increased with the maximum RMS value of ∼4.74 nm. Besides, absorption peak wavelength also was red-shifted from 500 nm to 551 nm under an influence of PEIE dopant concentrations. However, the turn on voltage gives no significant trend when dopant concentration was increased but the emission of the light was emitted when the voltage was below 8 V. Among four different dopant concentrations of MEH-PPV+PEIE, the brighter light emission was observed at 0.3 wt% of PEIE. Apparently, the concentration of dopant solution gives a significant contribution to the performance of OLED in terms of structural, optical and electrical properties.
  • Publication
    The efficiency effect of dye sensitized solar cell using different ratio of organic polymer doped titanium dioxide at different annealing process temperature
    ( 2020-01-08)
    Norhisamudin N.A.
    ;
    Norhayati Sabani
    ;
    Rosli N.
    ;
    Mohd Fairus Ahmad
    ;
    Juhari N.
    ;
    Safizan Shaari
    ;
    Zakaria N.
    Titanium Dioxide (TiO2) is one of the main materials in Dye Sensitized Solar Cell (DSSC). It is well known with its property of good optical transmittance and its mesoporous surface that can absorb generous amount of dye. In this study, TiO2 is fabricated using spin coating technique that leads to the uniform thickness of TiO2 layer. The thickness of the TiO2 can be controlled layer by layer using same technique to get an optimized surface that can lead to better performance of DSSC. In order to achieve this, the surface roughness of TiO2 must be as high as possible. Therefore, the organic material which is Poly(2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylene-vinylene (MEH-PPV) is used as medium to increase the mesoporous roughness structure of TiO2 nanocrystal film for DSSC. MEH-PPV is doped into the TiO2 using 0.5 mg/ml with different temperatures of 100°C and 450°C. Different temperatures of MEH-PPV will lead to the different surface structures for TiO2 thin film. The ratio of TiO2:MEH-PPV used were 1:1 and 2:1. The surface of TiO2 thin film was characterized using Atomic Force Microscope (AFM). The efficiency was obtained using Solar Simulator based on the voltage and current flow. Based on the results, the increment of surface roughness is about 21% for the different ratio at various temperatures. The optimum temperature and suitable ratio of TiO2:MEH-PPV was obtained via annealing process at 450°C with the ratio of 2:1. It gives the highest efficiency which is 0.1266%. These two important findings yield good mesoporous surface of TiO2 thin film.
  • Publication
    Solvent Effect on the Electrical and Structural Properties for MEH-PPV Organic Light Emitting Diodes (OLED)
    ( 2021-03-01)
    Ismail N.A.N.
    ;
    Safizan Shaari
    ;
    Juhari N.
    ;
    Norhayati Sabani
    ;
    Ahmad M.F.
    ;
    Zakaria N.F.
    In this paper, the performance of the electrical properties (J-V) and surface roughness of MEH-PPV based organic light-emitting diodes (OLED) towards solvent effect was investigated. The MEH-PPV layer was deposited using spin coating technique at fixed spun speed of 3000 rpm. Two different solvents, toluene and chloroform (CHCl3) and mixture toluene:CHCl3 with the ratio of 4:1 and 1:4 were used to dilute MEH-PPV at fixed concentration of 5 mgml-1. Apparently, the mixture of solvent makes the surface roughness of the MEH-PPV films reduced to 0.15 nm and 3.59 nm under the ratio 4:1 and 1:4 respectively. Besides, the mixture solvents makes the value of turn on voltage was dropped to ∼7.2 V and ∼9 V respectively compared to non-mixture solvent. The combination of different solvent apparently gives an effect on the electrical and structural properties of organic light-emitting diode.
  • Publication
    Photoluminescence measurement of triplet sensitizer-emitter solution using a customized 3D-printed sample holder
    ( 2024-06)
    Kelvin Voon Yan Jie
    ;
    Safizan Shaari
    ;
    Mohd Fairus Ahmad
    ;
    Nor Farhani Zakaria
    ;
    Norhayati Sabani
    This study explores the photoluminescence (PL) measurement of triplet sensitizer-emitter (TSE) solutions using a custom 3D-printed sample holder, within the context of triplet-triplet annihilation based molecular photon upconversion (TTA-UC) systems targeting the Vis-to-UV spectral region. TTA-UC converts low-energy visible photons to higher-energy ultraviolet (UV) photons, holding promise for solar energy harvesting and photonics applications. Two TSE couples, 4CzIPN/TP and 4CzIPN/QP, were investigated, and their upconverted fluorescence spectra showed peaks at 344 nm and 354 nm / 370 nm, respectively, confirming efficient upconversion capabilities. The 3D-printed sample holder facilitated reproducible PL measurements, enabling the calculation of quantum yields (ΦUC). The 4CzIPN/TP and 4CzIPN/QP couples exhibited low quantum yields (0.028% and 0.043%, respectively), suggesting the need for improved deoxygenation methods to enhance the triplet-triplet annihilation process and overall quantum efficiency. Despite modest yields, successful UV upconverted fluorescence observation underscores the feasibility of the Vis-to-UV TTA-UC system. This study provides insights into TTA-UC optimization and demonstrates the utility of the 3D-printed sample holder for affordable and precise PL measurements, paving the way for future advancements in photonics and solar energy applications.
  • Publication
    Modification of Photoanode Surface Structure via Image Analysis on Organic Polymer Material based for Dye-Sensitized Solar Cell (DSSC) Applications
    ( 2021-12-01)
    Nur Liyana Mohd Rosli
    ;
    Norhayati Sabani
    ;
    Mohd Fairus Ahmad
    ;
    Mohd. Azarulsani Md. Azidin
    ;
    Nurjuliana Juhari
    ;
    Nor Farhani Zakaria
    ;
    Mohd Natashah Norizan
    ;
    Safizan Shaari
    In this study, the experiment on the modification of the photoanode with organic polymer material as copolymer template for dye-sensitized solar cell (DSSC) applications has been conducted. The two organic copolymer templates are polystyrene sphere (PS) and poly[2-methoxy-5(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV). The modification photoanodes were made using Dr. Blade’s method. These organic copolymer templates were added to improve the surface of the mesoporous titanium dioxide (TiO2) layer, which is used as the main component in DSSC photoanode. The unmodified TiO2 photoanode has poor aggregation and porosity of TiO2. The addition of either MEH-PPV or PS sphere to the photoanode layer was found to affect the surface of mesoporous TiO2 in terms of porosity, particle size distribution and shape. The analysis of the TiO2 modification was conducted using an image analysis processing method via a 2D scanning electron microscope (SEM) image. The image analysis processing method used was the ImageJ program. The DSSC of modified photoanode is fabricated using metal complex dye, Ruthenium (N719) dye. The data collected from the ImageJ program showed that by adding organic copolymer templates into TiO2, the porosity of TiO2 decreased from 45 % to 42 %. From the photovoltaic analysis obtained, the J-V characteristic is recorded with the photoanode of TiO2 mixed with 1.00 wt% MEH-PPV gave the highest efficiency, which is 0.01 % with the following parameters – Voc = 0.43 V, Jsc = 0.17 mA/cm2 and FF = 0.20. Meanwhile, the photoanode of TiO2 mixed with 0.50 wt% PS sphere gave the highest efficiency which is 0.08 % with the following parameters – Voc = 0.39 V, Jsc = 0.86 mA/cm2 and FF = 0.25.