Kamarudin Hussin
Thumbnail Image
Preferred name
Kamarudin Hussin
Official Name
Hussin, Kamarudin
Alternative Name
Hussin, K.
Hussin, Kamarudin
Kamarudin, Hussin
Kamaruddin, Hussin
Kamaruddin, H.
Husin, Kamarudin
Main Affiliation
Scopus Author ID
16642513600
Researcher ID
FZF-9851-2022

Research Output

Filters

11 1
4 1
11
Reset filters

Settings
Now showing 1 - 10 of 11
  • Publication
    The physical and mechanical properties of fly ash geopolymers with various S/L ratios
    ( 2020-11-02)
    Teng N.H.
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Yong-Sing N.
    ;
    Kamarudin Hussin
    In the present work, a study of the effect of different solid/liquid (S/L) ratio on fly ash geopolymer was investigated. The geopolymer were prepared by mixing fly ash with alkali activator (a mixture of sodium hydroxide and sodium silicate). The S/L ratios were used 1.0, 1.5, 2.0, 2.5, 3.0 and 3.5 with fixed sodium silicate/sodium hydroxide ratio of 2.5 and 8M of sodium hydroxide. The geopolymers were cured at room temperature (29°C) for 24 hours and at 60°C for another 24 hours. The testing and analysis of the fly ash geopolymers were performed after 28 days. The geopolymer showed highest compressive strength (37.6MPa) with 3.0 of S/L ratio, further decreased in compressive strength (2.7MPa) was observed at 3.5.
      1
  • Publication
    Correlation between pore structure, compressive strength and thermal conductivity of porous metakaolin geopolymer
    ( 2020-06-30)
    Jaya N.A.
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Kamarudin Hussin
    This paper investigates the effect of mixing parameters (that are, alkali concentration, AA ratio, and MK/AA ratio) on the thermal conductivity of metakaolin geopolymers. The combination effect of foaming agent (H2O2) and surfactant (Tween 80) on the physical properties, compressive strength, and pore characteristic was also elucidated. Results showed that metakaolin geopolymer with maximum compressive strength of 33 MPa, bulk density of 1680 kg/m3, porosity of 18% and thermal conductivity of 0.40 W/mK were achieved with alkali concentration of 10 M, AA ratio of 1.0 and MK/AA ratio of 0.8. Gradation analysis demonstrated that AA ratio was the strength determining factor. Whilst, thermal conductivity was dependent on the MK/AA ratio. Adding H2O2 and surfactant produced geopolymer foam with acceptable compressive strength (0.4–6 MPa). The geopolymer foam had bulk density of 471–1212 kg/m3, porosity of 36–86% and thermal conductivity of 0.11–0.30 W/mK. Pore structure, size, and distribution were governed by H2O2 and surfactant dosages that have a great impact on the compressive strength. Narrower pore distribution and smaller pore diameter were achieved when both foaming agent and surfactant were used instead of foaming agent alone. The pore size and distribution varied to a greater extent with varying H2O2 contents. Surfactant illustrated distinct pore stabilizing effect at low H2O2 (<0.75 wt%) which diminished at high H2O2 content. In terms of thermal conductivity, even with increasing porosity at high H2O2 and surfactant content, the thermal conductivity did not show substantial reduction due to the interconnected pores as a result of pore coalescence.
      1
  • Publication
    Effect of sodium hydroxide molarity on physical, mechanical and thermal conductivity of metakaolin geopolymers
    ( 2018)
    Nur Ain Jaya
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Heah Cheng Yong
    ;
    Kamarudin Hussin
    In the present work, the effect of different sodium hydroxide (NaOH) molarity (6M, 8M, 10M, 12M and 14M) on the physical, mechanical and thermal conductivity of metakaolin geopolymers (MkGPs) was investigated. Geopolymers were prepared by activating the metakaolin with a mixture of NaOH with sodium silicate (Na₂SiO₃). The products obtained were characterized after 28 days of curing. The density, porosity, compressive strength and thermal conductivity (TC) were determined. In general, the NaOH molarity has a significant effect on the compressive strength of the MkGPs. The highest compressive strength was 14.6 MPa achieved with 10M of NaOH solution. The thermal conductivity of MkGPs measured in this work was low in the range between 0.71-0.97 W/mK. NaOH molarity had a significant effect on compressive strength but a marginal effect on thermal conductivity of MkGPs. The thermal conductivity was mainly affected by the bulk density and thus the total porosity. The results showed that the geopolymer can be considered to be used as the thermal insulating material.
      1  13
  • Publication
    Compressive strength and thermal conductivity of metakaolin geopolymers with anisotropic insulations
    ( 2020-03-18)
    Jaya N.A.
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Kamarudin Hussin
    ;
    Heah Cheng Yong
    ;
    Bayuaji R.
    ;
    Muhammad Faheem Mohd. Tahir
    This research investigated the properties of thermally insulating geopolymer prepared using waste filler (fibreboard and rubber) to act as anisotropic pore/insulation. The geopolymer matrix was synthesised using metakaolin and an alkaline solution consists of sodium hydroxide solution and sodium silicate mixture. Geopolymers with varying content (0, 3, 5 and 7 layers) of coin-shaped fibreboard and expanded polystyrene are produced to examine the anisotropic insulation effect on the material characteristics. The compressive strength and thermal conductivity were determined experimentally. From the results, it is proved that the use of anisotropic insulations can improve the thermal conductivity and minimizing the reduction of compressive strength. Geopolymer incorporated with fibreboard had better performance in terms of strength while geopolymer incorporated with rubber had better thermal conductivity.
      1
  • Publication
    Effect of alkali concentration on fly ash geopolymers
    ( 2018)
    Siti Fatimah Azzahran Abdullah
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Heah Cheng Yong
    ;
    Khairunnisa Zulkifly
    ;
    Kamarudin Hussin
    This paper presents the effect of NaOH concentration on fly ash geopolymers with compressive up to 56 MPa at 12M. The physical and mechanical on fly ash geopolymer are investigated. Test results show that the compressive strength result complied with bulk density result whereby the higher the bulk density, the higher the strength. Thus, the lower water absorption and porosity due to the increasing of NaOH concentration.
      1  8
  • Publication
    Effect of sodium hydroxide molarity on physical, mechanical and thermal conductivity of metakaolin geopolymers
    ( 2018)
    Nur Ain Jaya
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Heah Cheng Yong
    ;
    Kamarudin Hussin
    In the present work, the effect of different sodium hydroxide (NaOH) molarity (6M, 8M, 10M, 12M and 14M) on the physical, mechanical and thermal conductivity of metakaolin geopolymers (MkGPs) was investigated. Geopolymers were prepared by activating the metakaolin with a mixture of NaOH with sodium silicate (Na2SiO3). The products obtained were characterized after 28 days of curing. The density, porosity, compressive strength and thermal conductivity (TC) were determined. In general, the NaOH molarity has a significant effect on the compressive strength of the MkGPs. The highest compressive strength was 14.6 MPa achieved with 10M of NaOH solution. The thermal conductivity of MkGPs measured in this work was low in the range between 0.71-0.97 W/mK. NaOH molarity had a significant effect on compressive strength but a marginal effect on thermal conductivity of MkGPs. The thermal conductivity was mainly affected by the bulk density and thus the total porosity. The results showed that the geopolymer can be considered to be used as the thermal insulating material.
      5  39
  • Publication
    Effect of Solid-to-Liquid Ratio on Thin Fly Ash Geopolymer
    ( 2020-03-18)
    Yong-Sing N.
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Hui-Teng N.
    ;
    Kamarudin Hussin
    ;
    Heah Cheng Yong
    ;
    Nurul Aida Mohd Mortar
    ;
    Sandu A.V.
    The present work studies the effect of solid-to-liquid (S/L) ratio on the properties of thin fly ash-based geopolymer. The fly ash geopolymers with dimension of 160 mm × 40 mm × 10 mm were synthesised by using various S/L ratios (1.5, 2.0, 2.5, 3.0 and 3.2). The alkali activator was prepared by mixing 10M sodium hydroxide (NaOH) solution and sodium silicate (Na2SiO3) with the Na2SiO3/NaOH ratio of 2.5. The samples were cured at 60°C for 6 hours. The performance of fly ash geopolymers was evaluated by testing the flexural strength after 28 days. Results showed that the S/L ratio had an effect on flexural strength. The optimum flexural strength of 5.12 MPa was achieved by the fly ash geopolymer with S/L ratio of 2.5. However, the flexural strength dropped with higher S/L ratio as the workability decreases. However, further experimental lab work should be carried out as there is less knowledge in the study on the flexural strength of thin fly ash geopolymer.
      1
  • Publication
    Manufacturing of fire resistance geopolymer: a review
    ( 2016)
    Ikmal Hakem Aziz
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Kamarudin Hussin
    ;
    Aeslina Abdul Kadir
    ;
    Emy Aizat Azimi
    Protection against fire using inorganic polymer is a new application of engineering technology. Even though, there are varieties of fire-protection materials, there is always a need for the development of new materials with improved thermophysical properties and low cost. Geopolymer composites materials are promising from this point of view. Granulated blast furnace slag, boiler ash and fly ash have been used as the prime materials for forming geopolymers composites. Geopolymers have been studied due to its unique properties such as a good fire resistance. Geopolymer offers an innovative for application associated with the high thermal application. This paper summarizes on the potential of alkaliactivated materials over the past decades along with outlines of the manufacturing of geopolymer composites for fire resistance application.
      7  17
  • Publication
    Fly ash-metakaolin blend geopolymers under thermal exposures: Physical and mechanical performances
    ( 2020-11-02)
    Zulkifly K.
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Kamarudin Hussin
    ;
    Abdullah S.F.A.
    In this paper, an experimental study on the thermo-mechanical properties of fly ash-metakaolin blend geopolymers is presented. Visual observations, density and mass loss and compression test were conducted on geopolymers heated in a furnace at 200 °C, 400 °C, 600 °C, 800 °C and 1000 °C with a heating rate of 10 °C/min and soaking time of 1 hours. Fly ash-metakaolin blend geopolymers possessed excellent strength of 54.7MPa at ambient temperature and degraded 23.4% to 41.9MPa when exposed 200?C. The tested result show that the geopolymer can perform good residual strength (up to 23.2MPa) after 600?C. The strength of geopolymers decreased to 5.8MPa with increasing temperature up to 800?C. Even so, the geopolymers could withstand high temperature and remained intact. The higher mass loss due to the liberation of water from the surface, led to significant strength degradation in fly ash-metakaolin blend geopolymers. However, geopolymer gels exhibited structural stability at 1000°C, since at this temperature it promotes the reaction of the residue fly ash and metakaolin in the geopolymer samples, leading to a strength increase to 9.1MPa Employing blend fly ash and metakaolin as a precursor in the geopolymers helped to minimize the disruption effect caused by high temperature exposures.
      1
  • Publication
    Thermal resistance variations of fly ash geopolymers : Foaming responses
    ( 2017)
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Kamarudin Hussin
    This paper presents a comparative study of the characteristic of unfoamed and foamed geopolymers after exposure to elevated temperatures (200–800 °C). Unfoamed geopolymers were produced with Class F fly ash and sodium hydroxide and liquid sodium silicate. Porous geopolymers were prepared by foaming with hydrogen peroxide. Unfoamed geopolymers possessed excellent strength of 44.2 MPa and degraded 34% to 15 MPa in foamed geopolymers. The strength of unfoamed geopolymers decreased to 5 MPa with increasing temperature up to 800 °C. Foamed geopolymers behaved differently whereby they deteriorated to 3 MPa at 400 °C and increased up to 11 MPa at 800 °C. Even so, the geopolymers could withstand high temperature without any disintegration and spalling up to 800 °C. The formation of crystalline phases at higher temperature was observed deteriorating the strength of unfoamed geopolymers but enhance the strength of foamed geopolymers. In comparison, foamed geopolymer had better thermal resistance than unfoamed geopolymers as pores provide rooms to counteract the internal damage.
      1  9