Mohd. Mustafa Al Bakri Abdullah
Thumbnail Image
Preferred name
Mohd. Mustafa Al Bakri Abdullah
Official Name
Abdulah, Mohd. Mustafa Al Bakri
Alternative Name
Abdullah, M.M.A.
M.M.A. Abdullah
Mustafa Al Bakri, A. M.
Albakri Abdullah, M. M.
Main Affiliation
CeGeoGTech UniMAP
Scopus Author ID
53164519100

Research Output
Now showing 1 - 6 of 6
  • Publication
    Contribution of interfacial bonding towards geopolymers properties in geopolymers reinforced fibers: a review
    ( 2022)
    Muhd Hafizuddin Yazid
    ;
    Meor Ahmad Faris bin Meor Ahmad Tajudin
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Marcin Nabiałek
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Marwan Kheimi
    ;
    Andrei Victor Sandu
    ;
    Adam Rylski
    ;
    Bartłomiej Jeż
    There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.
      22  2
  • Publication
    Crumb rubber geopolymer mortar at elevated temperature exposure
    ( 2022)
    Ahmad Azrem Azmi
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Che Mohd Ruzaidi Ghazali
    ;
    Romisuhani Ahmad
    ;
    Ramadhansyah Putra Jaya
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohammad A. Almadani
    ;
    Wysłocki, Jerzy J.
    ;
    Agata Śliwa
    ;
    Andre Victor Sandu
    Low calcium fly ash is used as the main material in the mixture and the crumb rubber was used in replacing fine aggregates in geopolymer mortar. Sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) which were high alkaline solution were incorporated as the alkaline solution. The fly ash reacted with the alkaline solution forming alumino-silicate gel that binds the aggregate to produce a geopolymer mortar. The loading of crumb rubber in the fly ash based geopolymer mortar was set at 0%
      3  18
  • Publication
    Contribution of interfacial bonding towards geopolymers properties in geopolymers reinforced fibers: A review
    ( 2022)
    Muhd Hafizuddin Yazid
    ;
    Meor Ahmad Faris bin Meor Ahmad Tajudin
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Marcin Nabiałek
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Marwan Kheimi
    ;
    Andrei Victor Sandu
    ;
    Adam Rylski
    ;
    Bartłomiej Jeż
    There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.
      6  18
  • Publication
    Thermal insulation and mechanical properties in the presence of glas bubble in fly ash geopolymer paste
    ( 2021)
    Noor Fifinatasha Shahedan
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Norsuria Mahmed
    ;
    Liew Yun Ming
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Ikmal Hakem A Aziz
    ;
    Aeslina Abdul Kadir
    ;
    Andrei Victor Sandu
    ;
    Mohd Fathullah Ghazli@Ghazali
    The density, compressive strength, and thermal insulation properties of fly ash geopolymer paste are reported. Novel insulation material of glass bubble was used as a replacement of fly ash binder to significantly enhance the mechanical and thermal properties compared to the geopolymer paste. The results showed that the density and compressive strength of 50% glass bubble was 1.45 g/ ely, meeting the standard requirement for structural concrete. Meanwhile, the compatibility of 50% glass bubbles tested showed that the thermal conductivity (0.898 W/mK), specific heat (2.141 MJ/m3 K), and thermal diffusivity(0.572 mm2/s) in meeting the same requirement. The improvement of thermal insulation properties revealed the potential use of glass bubbles as an insulation material in construction material
      5  14
  • Publication
    Mechanical performance of Fly Ash based Geopolymer (FAG) as road base stabilizer
    ( 2022)
    Liyana Ahmad Sofri
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Andrei Victor Sandu
    ;
    Thanongsak Imjai
    ;
    Petrica Vizureanu
    ;
    Mohd Rosli Mohd Hasan
    ;
    Mohammad Almadani
    ;
    Ikmal Hakem Ab Aziz
    ;
    Farahiyah Abdul Rahman
    This study examines the strength development of fly ash-based geopolymer (FAG) as a stabilizer for road base material for pavement construction. In the last decade, there has been a rapid development of conventionally treated bases, such as cement-treated bases. However, a major problem with this kind of application is the shrinkage cracking in cement-treated bases that may result in the reflection cracks on the asphalt pavement surface. This study explores the effects of FAG on base layer properties using mechanistic laboratory evaluation and its practicability in pavement base layers. The investigated properties are flexural strength (FS), unconfined compressive strength (UCS), shrinkage, and resilient modulus (RM), as well as indirect tensile strength (ITS). The findings showed that the mechanical properties of the mixture enhanced when FAG was added to 80–85% of crushed aggregate, with the UCS being shown to be a crucial quality parameter. The effectiveness of FAG base material can have an impact on the flexible pavements’ overall performance since the base course stiffness directly depends on the base material properties. As a stabilizing agent for flexible pavement applications, the FAG-stabilized base appeared promising, predicated on test outcomes.
      6  22
  • Publication
    Chemical distributions of different Sodium Hydroxide molarities on fly ash/dolomite-based geopolymer
    ( 2022)
    Wan Mastura Wan Ibrahim
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Romisuhani Ahmad
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    ;
    Omrane Benjeddou
    ;
    Afikah Rahim
    ;
    Masdiyana Ibrahim
    ;
    Ahmad Syauqi Sauffi
    Geopolymers are an inorganic material in an alkaline environment that is synthesized with alumina–silica gel. The structure of geopolymers consists of an inorganic chain of material and a covalent-bound molecular system. Currently, Ordinary Portland Cement (OPC) has caused carbon dioxide (CO2) emissions which causes greenhouse effects. This analysis investigates the impact on fly ash/dolomite-based-geopolymer with various molarities of sodium hydroxide solutions which are 6 M, 8 M, 10 M, 12 M and 14 M. The samples of fly ash/dolomite-based-geopolymer were prepared with the usage of solid to liquid of 2.0, by mass and alkaline activator ratio of 2.5, by mass. After that, the geopolymer was cast in 50 × 50 × 50 mm molds before testing after 7 days of curing. The samples were tested on compressive strength, density, water absorption, morphology, elemental distributions and phase analysis. From the results, the usage of 8 M of NaOH gave the optimum properties for the fly ash/dolomite-based geopolymer. The elemental distribution analysis exposes the Al, Si, Ca, Fe and Mg chemical distribution of the samples from the selected area. The distribution of the elements is related to the compressive strength and compared with the chemical composition of the fly ash and dolomite.
      1  18