Nur Liza Rahim
Thumbnail Image
Preferred name
Nur Liza Rahim
Official Name
Nur Liza, Rahim
Alternative Name
Rahim, Nur Liza
Rahim, N. L.
Rahim, Nur Alis Addiena A.
Main Affiliation
Scopus Author ID
55754434900

Research Output

Filters

22
Reset filters

Settings
Now showing 1 - 10 of 22
  • Publication
    Investigating the effect of steel wire and carbon black from worn out tyre on the strength of concrete
    ( 2024-10)
    Norlia Mohamad Ibrahim
    ;
    Ali Naqiuddin Zamah Shari
    ;
    Nur Zakiah Anis Abdul Rahim
    ;
    Nur Liza Rahim
    ;
    Mustaqqim Abdul Rahim
    ;
    Roshazita Che Amat
    ;
    Norshah Aizat Shuaib
    ;
    György Deak
    Technology in concrete is rapidly developing to improve the quality and properties of concrete. One of the many recycled materials is worn-out tyres. Currently, the use of tires is very widespread considering the use of vehicles that increase from time to time. Piles of discarded tires can cause a lot of damage to the environment. So, by using steel wire waste (SWW) as new fiber reinforcement in concrete and with the combination with carbon black (CB), it is hoped that, by doing this, not only it could improve the quality of concrete, but also preserves the environment. Therefore, the objective of this research was, to identify the properties of fresh concrete with the addition of SWW and CB, and also to investigate the physical and mechanical properties of hardened concrete, incorporating of SWW as additional fiber reinforcement and CB. For fresh concrete, workability using a slump test was conducted. Several tests were carried out on the properties of hardened concrete. Among them were compressive strength, flexural strength, splitting tensile strength, and water absorption. The physical appearance of the concrete has also been examined and recorded. There are four batches of concrete which consist of one control batch and three batches of concrete with various weights of SWW which are in the portion of 300 g, 600 g, and 900 g, and the weight of CB is maintained at 300 g for all batches. For workability, all concrete batches with the addition of SWW and CB show acceptable workability. For the case of the density of fresh concrete, samples containing 900 g addition of SWW have the highest density which was 2520 kg/m³, as expected. Results for water absorption show that the lowest value is contributed by the control sample which was 7.6%. For compressive and flexural strength, 300 g addition of SWW has the highest value which was 28.52 MPa for compressive strength and 7.52 MPa for flexural strength. Lastly, for splitting tensile strength, the highest value was also obtained when 300 g addition of SW was added which was 5.4 MPa. To conclude, SWW and CB can be added to concrete to obtain comparable strength of concrete. However, some modifications could be made to both recycle materials to improve concrete performance.
  • Publication
    Preservation of Natural Resources by Utilizing Combustion Ash In Concrete and Determination of Its Engineering Properties
    ( 2023-01-01)
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Syakirah Afiza Mohammed
    ;
    Roshazita Che Amat
    ;
    Rahim M.A.
    ;
    Zailani W.W.A.
    ;
    Laslo L.
    ;
    Muhamad N.
    Due to the large amount of combustion ash being thrown into landfills, which can lead to environmental pollution, new alternatives to construction materials can be developed by utilising this combustion ash as a part of the main raw materials, while at the same time helping to preserve natural resources in the concrete manufacturing industry. Generally, using new waste materials will eventually affect the engineering properties of concrete. Therefore, the main objective of this study is to analyse the engineering properties of concrete containing combustion ash as a partial replacement for ordinary Portland cement (OPC). CA can be classified as combustion bottom ash (CBA) and combustion fly ash (CFA). CA is tested for its chemical compositions using X-Ray Fluorescence (XRF), and its four main compositions, which are silica, alumina, iron, and calcium, are examined and discussed extensively. Other testing for the property of CA includes Scanning Electron Microscopic (SEM) and specific gravity testing for coarse aggregate. To produce sustainable concrete from waste, several tests have been conducted to determine the engineering properties of the concrete, such as compressive strength, flexural strength, and splitting tensile strength. Results show that CA, which consists mainly of silica dioxide, contributed to the strength of concrete. SEM images show that CBA has a porous structure with an angular and rough texture, whereas CFA has more rounded particles, which influence the overall compressive strength. Furthermore, it was discovered that as the proportion of CBA utilised increased, the compressive strength, flexural strength, and splitting tensile strength of the concrete improved. Based on the results of the testing, CBA is suggested for use as a supplementary cementitious material in concrete.
  • Publication
    Workability and density of concrete containing Coconut Fiber
    ( 2022-01-01)
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Roshazita Che Amat
    ;
    Mustaqqim Abdul Rahim
    ;
    Woo Chin Kah
    ;
    Irnis Azura Zakaria
    ;
    Moncea Andreea
    Use of natural fiber in concrete to enhance the strength of concrete have been used widely and become as part of an alternative building materials. For instance, the use of coconut fiber (CF) which are non-hazardous, environmental-friendly and can improves the engineering properties of concrete. The aim of this study is to identify the workability and density of CF modified concrete. CF were added into the mixture in 3 different amount that is 200 g, 400 g, and 600 g. The size of the cube samples is 100 × 100 × 100 mm and were cured for 14 days, and 28 days. To evaluate the effect of CF in improving the properties of concrete, the properties of ordinary concrete are used as a reference which consist 0% CF. The fresh and hardened densities for all samples also show that when more fiber was added into mixture, densities reduced. As summary, the study shows that by adding CF in concrete reduced the workability and density of concrete.
      8  1
  • Publication
    Comparing the Physical Properties of Coal Bottom Ash (CBA) Waste and Natural Aggregate
    ( 2022-01-01)
    Syakirah Afiza Mohammed
    ;
    Mohamed Reyad Alhadi Ahmad
    ;
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Roshazita Che Amat
    ;
    Samsudin S.
    Coal bottom ash (CBA) is a co-combustion product material, which may cause hazards to human health and the environment. Rapid growth in technology causes the increase of CBA waste and this situation led to a waste disposal crisis. Reuse waste material as an alternative material instead of natural materials can led to sustainable and environmentally friendly construction. The main objective of this study is to determine the physical properties of CBA and its suitability to be used as replacement material in civil construction. The physical properties test conducted in this research were aggregate impact value test, aggregate crushed value test, flakiness and elongation test. The results show that the ability of CBA to resist sudden shock and repeated load was lesser than natural aggregate (NA). The differences of aggregate impact value (AIV) and aggregate crushing value (ACV), between NA and CBA were 50.4% and 48.9%, respectively. In addition, CBA has higher amount of flaky and elongated particles compared to NA. The flakiness index value for NA and CBA were 7.12% and 26.10%, respectively while the difference value of elongation index between NA and CBA was 37%. However, even though the properties of CBA were not as good as NA, the results for ACV and the flakiness index of CBA meet the minimum requirement of Jabatan Kerja Raya (JKR) Standard Specification which indicates that CBA has potential to be used in civil construction.
      2  16
  • Publication
    Strength development of concrete containing municipal solid waste incineration bottom ash and metakaolin
    ( 2024-03-21)
    Roshazita Che Amat
    ;
    Khairul Nizar Ismail
    ;
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Loong W.J.
    The study was related to the influence of the properties of concrete by using different percentage of metakaolin and fixed percent of bottom ash to partially replace the cement. Cement is a well-known building material and used for the construction in the world. Moreover, the used of metakaolin (MK) and bottom ash (BA) in concrete has received considerable attention in recent years. By using bottom ash, it could reduce the land filling space. X-Ray Fluorescence (XRF) test was used to determine the chemical composition of bottom ash and metakaolin. Four series of concrete have been examined, including control, bottom ash and metakaolin were used as partial replacement for cement at 10%BA+10%MK, 10%BA+15%MK and 10%BA+20%MK of concrete mixes by volume. The curing period for the samples are 7 days and 28 days. In order to determine the properties of concrete, the tests such as slump test, density test, water absorption test, pulse velocity test, rebound hammer test and compression test were performed. The results proved that the strength development of 10%BA + 10%MK concrete sample shows the highest compressive strength after 28 days curing.
      1
  • Publication
    Sustainable utilisation of quarry dust waste in concrete: Strength performance
    ( 2020-12-29)
    Nur Liza Rahim
    ;
    Abd Rahim, Noor Aini Syafiqah
    ;
    Norlia Mohamad Ibrahim
    ;
    Roshazita Che Amat
    ;
    Hamzah N.
    ;
    Misnon N.A.
    Each year, a large amount of quarry dust (QD) waste is disposed into landfills. This waste material was obtained as a by-product during the production of aggregates through the crushing process of rocks at the quarry site. The increasing value of waste will have a significant impact on health and the environment. Reusing such wastes by including them into building materials is a practical answer for the pollution problem. Therefore, this research was to observe the possibility of quarry dust to be included in a concrete mix. The quarry dust has been used as a partial replacement for cement proportion at different levels of replacement (25%, 30% and 35%). Quarry dust was used as the main material in this project to measure the effectiveness of concrete performance. In this research, the quarry dust composition was determined by using X-Ray Fluorescence Spectrometer (XRF). From the x-ray fluorescent spectrometry test result, the quarry dust displays some similar characteristics with the Ordinary Portland Cement (OPC) where it comprises a high composition of Calcium Oxide (CaO). Research were done to determine the optimum percentage of quarry dust in concrete. The result shows that 25% of quarry dust and 75% of cement is the best percentage that can be used in concrete mixture to reach the standard strength. From an economic point of view, the proposed optimum concrete mix was found to be the most economical with the reducing of RM 33 per 1 m3 of the concrete mixture. The results indicated that the quarry dust waste could be utilised as cement replacement to produce durable and resilient concrete. These materials could be an alternative low-cost material for concrete and at the same time provide a new disposal method for the waste.
      3  16
  • Publication
    Exploring the Properties of Mortar Containing Incineration Fly Ash
    ( 2021-11-26)
    Norlia Mohamad Ibrahim
    ;
    Rohaya Abdul Malek
    ;
    Nur Liza Rahim
    ;
    Mustaqqim Abdul Rahim
    ;
    Roshazita Che Amat
    ;
    Syakirah Afiza Mohammed
    ;
    Badri N.A.
    Fly Ash (FA) is one of the waste materials generated from the combustion of solid waste through incinerator and contains hazardous substances. Further treatment to the ash needs to be done to avoid further environmental destruction. As an alternative solution for this problem, FA is used as a replacement material for cement in the mortar. The main objective of this study is to explore the potential use of FA as partial replacement of cement in mortar. The percentage of FA used to replace the cement in this study is 0%, 5%, 10%, 15% and 20%. Several important tests were conducted to identify main properties of the mortar such as compressive strength, water absorption, density and ultra-pulse velocity. Mortar containing 15% of fly ash has the highest of compression strength which is 35 MPa after 28 days. Besides, the mortar containing 5% of fly ash has the highest result of water absorption test and density test whereas mortar containing 20% of fly ash has the highest value for pulse velocity after 28 days. Thus, mortar containing fly ash has good physical and mechanical properties.
      4
  • Publication
    Recycled Incineration Bottom Ash and Metakaolin as Sustainable Materials for Cement Replacement in Cementitious Composites
    ( 2023-01-01)
    Roshazita Che Amat
    ;
    Syakirah Afiza Mohammed
    ;
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Khairel Rafezi Ahmad
    ;
    Raischi M.
    Study was related to the influence of the concrete properties by using different percentages of metakaolin and fixed percent of incineration bottom ash to partially replace the cement. Cement is a well-known building material and used for the construction in the world. Moreover, the used of metakaolin (MK) and incineration bottom ash (IBA) in this research would give significance to our environment as it can reduce the usage of cement in concrete. By using bottom ash, it could reduce the land filling space. The X-Ray Fluorescence (XRF) test was used to determine the chemical composition of IBA and MK. Four series of concrete have been examined, including control, IBA and MK were used as partial replacement for cement at 10%IBA + 10%MK, 10%IBA + 15%MK and 10%IBA + 20%MK of concrete mixes by volume. The curing period for the samples is 7 days and 28 days. To determine the properties of concrete, the tests such as slump test, density test, water absorption test, pulse velocity test, rebound hammer test and compression test were performed. The results proved that the strength development of 10%IBA + 10%MK concrete sample shows the highest compressive strength after 28 days of curing.
      2
  • Publication
    Preservation of natural resources by utilizing combustion ash in concrete and determination of its engineering properties
    ( 2023-01-01)
    Norlia Mohamad Ibrahim
    ;
    Nur Liza Rahim
    ;
    Syakirah Afiza Mohammed
    ;
    Roshazita Che Amat
    ;
    Mustaqqim Abdul Rahim
    ;
    Zailani W.W.A.
    ;
    Laslo L.
    ;
    Muhamad N.
    Due to the large amount of combustion ash being thrown into landfills, which can lead to environmental pollution, new alternatives to construction materials can be developed by utilising this combustion ash as a part of the main raw materials, while at the same time helping to preserve natural resources in the concrete manufacturing industry. Generally, using new waste materials will eventually affect the engineering properties of concrete. Therefore, the main objective of this study is to analyse the engineering properties of concrete containing combustion ash as a partial replacement for ordinary Portland cement (OPC). CA can be classified as combustion bottom ash (CBA) and combustion fly ash (CFA). CA is tested for its chemical compositions using X-Ray Fluorescence (XRF), and its four main compositions, which are silica, alumina, iron, and calcium, are examined and discussed extensively. Other testing for the property of CA includes Scanning Electron Microscopic (SEM) and specific gravity testing for coarse aggregate. To produce sustainable concrete from waste, several tests have been conducted to determine the engineering properties of the concrete, such as compressive strength, flexural strength, and splitting tensile strength. Results show that CA, which consists mainly of silica dioxide, contributed to the strength of concrete. SEM images show that CBA has a porous structure with an angular and rough texture, whereas CFA has more rounded particles, which influence the overall compressive strength. Furthermore, it was discovered that as the proportion of CBA utilised increased, the compressive strength, flexural strength, and splitting tensile strength of the concrete improved. Based on the results of the testing, CBA is suggested for use as a supplementary cementitious material in concrete.
      8  16
  • Publication
    A Properties of Municipal Solid Waste Incineration Fly Ash (IFA) And Cement Used in The Manufacturing of New Inventive Blended Cement
    ( 2022-01-01)
    Norlia Mohamad Ibrahim
    ;
    Roshazita Che Amat
    ;
    Nur Liza Rahim
    ;
    Izzatul Nurain Che Sang Beri
    ;
    Syakirah Afiza Mohammed
    ;
    Zailani W.W.A.
    Municipal solid waste incinerator fly (IFA) ash is prone to accumulate high concentration heavy metals. Due to the increasing costs to treat remaining fly ash at the landfill, a lot of research has been done to recycle IFA. This study was focusing on the properties of IFA and cement as main raw materials in new inventive blended cement. The properties of blended cement were also being investigated. Properties of IFA and cement were examined through several test which includes density, specific gravity, X-Ray Fluorescence (XRF), Loss of Ignition (LOI) and through Toxicity Characteristic Leaching Procedure (TCLP) test. The density test and LOI test were also being done for the blended cement. From the tests for IFA and cement, it can be found that density the density of fly ash and cement that has been used for this study were found to be 0.76 g/cm3 and 3.67 g/cm3 respectively. Then, the specific gravity of fly ash and cement were 1.69 and 2.98, accordingly. XRF results shows that both materials have highest content of aluminium, silica and iron, as expected. LOI of fly ash and cement were found to be 17.33 % and 12.33 %, respectively. In terms of the leaching rates of heavy metals (Mn, Ni, Cd, Cr, Cu), only Cd leached at rate 2.39 mg/L, which is above the USEPA's regulatory level, 1.0 mg/L. 5 %, 10 % and 15 % of IFA was mixed with cement to produced blended cement. As the density of blended cement, it was found to be 1.12 g/cm3, 1.08 g/cm3 and 1.09 g/cm3 for each of 5 %, 10 % and 15 % of fly ash in blended cement.
      4  17