Muhammad Syamil Zakaria
Thumbnail Image
Preferred name
Muhammad Syamil Zakaria
Official Name
Muhammad Syamil, Zakaria
Alternative Name
Zakaria, Muhammad Syamil
Zakaria, M. S.
Main Affiliation
Scopus Author ID
57204783753

Research Output

Filters

3 1
1
3
Reset filters

Settings
Now showing 1 - 3 of 3
  • Publication
    Effect of zinc addition on the performance of aluminium alloy sacrificial anode for marine application
    ( 2017-09-26)
    Khan B.
    ;
    Rosli M.U.
    ;
    Hazrin Jahidi Jaafar
    ;
    Muhammad Ikman Ishak
    ;
    Muhammad Syamil Zakaria
    ;
    Mohd Riduan Jamalludin
    ;
    Khor Chu Yee
    ;
    Wan Mohd Faizal Wan Ab Rahim
    ;
    Rahim W.M.
    ;
    Mohd Al-Hafiz Mohd Nawi
    In this work, the effect of zinc addition on the performance of aluminum-based sacrificial anode in seawater was investigated. The parameters used in assessing the performance of the cast anodes are anodic efficiency, protection efficiency and polarized potential. The content of zinc in the anodes was varied after die casting. The alloys produced were tested as sacrificial anode for the protection of mild steel for marine application at room temperature. Factors such as reactivity of zinc particles in the seawater, corrosion activity during the period of experiment, pH of seawater and the electronegativity potential of zinc were collected for analysis. Overall findings shows addition of zinc increases rate of corrosion to the sacrificial anode and the protection offered by the sacrificial anodes measured and collected in PIT shows the seawater react to sacrificial anode and no porosity reaction between the anodes. The microstructure showed the intermetallic structures of β-phase which breakdown the alumina passive film, thus enhancing the anode efficiency.
  • Publication
    Chip morphology and surface integrity in turning AZ31 magnesium alloy under dry machining and submerged convective cooling
    ( 2023)
    Muhammad Syamil Zakaria
    ;
    Mazli Mustapha
    ;
    Azwan Iskandar bin Azmi
    ;
    Khor Chu Yee
    Magnesium alloys have broad applications, including medical implants and the aerospace sector owing to their great density and high strength-to-weight ratio. Dry cutting is a frequent technique for machining this material. However, it always leads to an excessive rise in temperature due to the absence of cooling at the cutting zone, which affects the machined surface integrity and chip morphology. In this study, chip morphology and surface integrity of the AZ31 magnesium alloy were investigated in the turning process using an internal cooling method called submerged convective cooling (SCC) to overcome the absence of cooling in dry cutting. This method can exploit the advantage of the high specific heat capacity of water as a cooling fluid without any reaction between water and magnesium to create a cooling element in the cutting zone. The chip morphologies and surface integrity were analyzed experimentally with varying cutting speeds under SCC and dry cutting. The experimental results revealed that SCC and dry cutting produced saw-tooth or serrated chip formation. The chips produced in dry cutting were continuous, while SCC was short and discontinuous as a result of a severe crack on the back surface of the chip. It was discovered that the grain refinement layer on the machined samples was thinner under SCC turning. SCC machining increased the microhardness of the AZ31 magnesium alloy by 60.5% from 55 HV to 88.3 HV, while dry turning exhibited a 49% increase in microhardness. The result revealed that surface roughness improved by 10.8%, 9.4% and 4.7% for cutting speeds (V) of 120, 180, and 240 m/min, respectively, under the SCC internal cooling. Based on the result obtained, SCC cutting outperformed dry cutting in terms of chip breakability, grain refinement, microhardness, and surface roughness.
  • Publication
    A study of energy consumption in turning process using lubrication of nanoparticles enhanced coconut oil (NECO)
    ( 2017-10-29)
    Ahmad Fairuz Mansor
    ;
    Muhammad Syamil Zakaria
    ;
    Azwan Iskandar Azmi
    ;
    Ahmad Nabil Mohd Khalil
    ;
    Musa N.A.
    Cutting fluids play very important role in machining application in order to increase tool life, surface finish and reduce energy consumption. Instead of using petrochemical and synthetic based cutting fluids, vegetable oil based lubricants is safety for operators, environmental friendly and become more popular in the industrial applications. This research paper aims to find the advantage of using vegetable oils (coconut oil) with additional of nano particles (CuO) as lubricant to the energy consumption during machining process. The energy was measured for each run from 2 level factorial experimental layout. Obtained results illustrate that lubricant with enhancement of nanoparticles has capability to improve the energy consumption during the machining process.