Mohd. Mustafa Al Bakri Abdullah
Thumbnail Image
Preferred name
Mohd. Mustafa Al Bakri Abdullah
Official Name
Abdulah, Mohd. Mustafa Al Bakri
Alternative Name
Abdullah, M.M.A.
M.M.A. Abdullah
Mustafa Al Bakri, A. M.
Albakri Abdullah, M. M.
Main Affiliation
CeGeoGTech UniMAP
Scopus Author ID
53164519100

Research Output
Now showing 1 - 3 of 3
  • Publication
    Microstructure and porosity evolution of alkali activated slag at various heating temperatures
    ( 2020)
    Ikmal Hakem Aziz
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    M.A.A. Mohd Salleh
    ;
    Sorachon Yoriya
    ;
    Jitrin Chaiprapa
    ;
    Catleya Rojviriya
    ;
    Long Yuan Li
    This paper elucidated the microstructural and porosity evolution of alkali activated slag at 800 °C up to 1200 °C. The microstructural analysis obtained shows the changes in surface densification of glassy phase and nucleation of dynamical grains within the alkali activated slag when in contact with high heating temperature. Using synchrotron radiation X-ray tomographic microscopy, the number of pores in alkali activated slag decreased with increasing heating temperature. The 3D pores distribution also demonstrated significant increase in the range size of ~20 μm with the appearance of isolated and intergranular pores at 1200 °C. These changes also led to the anorthite crystallisation indicated by high angle grain boundaries and preferred crystal orientation. The evolution of porosity and crystalline phase is contributed to the development of internal strain after heating at high temperature environment.
  • Publication
    Mechanical performance, microstructure, and porosity evolution of fly ash geopolymer after ten years of curing age
    ( 2023)
    Ikmal Hakem A. Aziz
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Rafiza Abd Razak
    ;
    Zarina Yahya
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Jitrin Chaiprapa
    ;
    Catleya Rojviriya
    ;
    Petrica Vizureanu
    ;
    Andrei Victor Sandu
    ;
    Muhammad Faheem Mohd. Tahir
    ;
    Alida Abdullah
    ;
    Liyana Jamaludin
    This paper elucidates the mechanical performance, microstructure, and porosity evolution of fly ash geopolymer after 10 years of curing age. Given their wide range of applications, understanding the microstructure of geopolymers is critical for their long-term use. The outcome of fly ash geopolymer on mechanical performance and microstructural characteristics was compared between 28 days of curing (FA28D) and after 10 years of curing age (FA10Y) at similar mixing designs. The results of this work reveal that the FA10Y has a beneficial effect on strength development and denser microstructure compared to FA28D. The total porosity of FA10Y was also lower than FA28D due to the anorthite formation resulting in the compacted matrix. After 10 years of curing age, the 3D pore distribution showed a considerable decrease in the range of 5–30 µm with the formation of isolated and intergranular holes.
      20  1
  • Publication
    Preparation of fly Ash-Ladle furnace slag blended geopolymer foam via Pre-Foaming method with polyoxyethylene alkyether sulphate incorporation
    ( 2022)
    Ng Hui-Teng
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Catleya Rojviriya
    ;
    Hasniyati Md Razi
    ;
    Sebastian Garus
    ;
    Marcin Nabiałek
    ;
    Wojciech Sochacki
    ;
    Ilham Mukriz Zainal Abidin
    ;
    Ng Yong-Sing
    ;
    Andrei Victor Sandu
    ;
    Agata Åšliwa
    This paper uses polyoxyethylene alkyether sulphate (PAS) to form foam via pre-foaming method, which is then incorporated into geopolymer based on fly ash and ladle furnace slag. In the literature, only PAS-geopolymer foams made with single precursor were studied. Therefore, the performance of fly ash-slag blended geopolymer with and without PAS foam was investigated at 29–1000 °C. Unfoamed geopolymer (G-0) was prepared by a combination of sodium alkali, fly ash and slag. The PAS foam-to-paste ratio was set at 1.0 and 2.0 to prepare geopolymer foam (G-1 and G-2). Foamed geopolymer showed decreased compressive strength (25.1–32.0 MPa for G-1 and 21.5–36.2 MPa for G-2) compared to G-0 (36.9–43.1 MPa) at 29–1000 °C. Nevertheless, when compared to unheated samples, heated G-0 lost compressive strength by 8.7% up to 1000 °C, while the foamed geopolymer gained compressive strength by 68.5% up to 1000 °C. The thermal stability of foamed geopolymer was greatly improved due to the increased porosity, lower thermal conductivity, and incompact microstructure, which helped to reduce pressure during moisture evaporation and resulted in lessened deterioration.
      1  27