Liew Yun Ming
Thumbnail Image
Preferred name
Liew Yun Ming
Official Name
Liew Yun Ming
Alternative Name
Yun-Ming, Liew
Liew, Y. M.
Yun Ming, Liew
Ming, Liew Yun
Liew, Yun Ming
Ming, L. Y.
Main Affiliation
Scopus Author ID
57204242778
Researcher ID
S-7164-2019

Research Output
Now showing 1 - 5 of 5
  • Publication
    The effect of different ratio bottom ash and fly ash geopolymer brick on mechanical properties for non-loading application
    ( 2017)
    Laila Mardiah Deraman
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Liew Yun Ming
    ;
    Kamarudin Hussin
    ;
    Wan Mastura Wan Ibrahim
    ;
    Andrei Victor Sandu
    This paper studies the finding of strength and water absorption of geopolymer bricks using bottom ash and fly ash as a geopolymer raw material for non-loading application with minimum strength. The study has been conducted to produce bottom ash and fly ash geopolymer bricks by varying the ratio of fly ash-to-bottom ash, solid-to-liquid and sodium silicate (Na2SiO3)-to-sodium hydroxide (NaOH) in the mixing process. The compressive strength range between 3.8-4.5 MPa was obtained due to the minimum strength of non-loading application with 70°C curing temperature within 24 hours at 7 days of ageing. The optimum ratio selected of bottom ash-to-fly ash, solid-to-liquid and Na2SiO3-to-NaOH are 1:2, 2.0 and 4.0 respectively. The water absorption result is closely related to the amount of bottom ash used in the mix design.
  • Publication
    Recent developments in steelmaking industry and potential alkali activated based steel waste: A comprehensive review
    ( 2022)
    Ikmal Hakem Aziz
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Liew Yun Ming
    ;
    Long Yuan Li
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    ;
    Ovidiu Nemes
    ;
    Shaik Numan Mahdi
    The steel industry is responsible for one-third of all global industrial CO2 emissions, putting pressure on the industry to shift forward towards more environmentally friendly production methods. The metallurgical industry is under enormous pressure to reduce CO2 emissions as a result of growing environmental concerns about global warming. The reduction in CO2 emissions is normally fulfilled by recycling steel waste into alkali-activated cement. Numerous types of steel waste have been produced via three main production routes, including blast furnace, electric arc furnace, and basic oxygen furnace. To date, all of the steel waste has been incorporated into alkali activation system to enhance the properties. This review focuses on the current developments over the last ten years in the steelmaking industry. This work also summarizes the utilization of steel waste for improving cement properties through an alkali activation system. Finally, this work presents some future research opportunities with regard to the potential of steel waste to be utilized as an alkali-activated material.
  • Publication
    Preparation of fly Ash-Ladle furnace slag blended geopolymer foam via Pre-Foaming method with polyoxyethylene alkyether sulphate incorporation
    ( 2022)
    Ng Hui-Teng
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Catleya Rojviriya
    ;
    Hasniyati Md Razi
    ;
    Sebastian Garus
    ;
    Marcin Nabiałek
    ;
    Wojciech Sochacki
    ;
    Ilham Mukriz Zainal Abidin
    ;
    Ng Yong-Sing
    ;
    Andrei Victor Sandu
    ;
    Agata Śliwa
    This paper uses polyoxyethylene alkyether sulphate (PAS) to form foam via pre-foaming method, which is then incorporated into geopolymer based on fly ash and ladle furnace slag. In the literature, only PAS-geopolymer foams made with single precursor were studied. Therefore, the performance of fly ash-slag blended geopolymer with and without PAS foam was investigated at 29–1000 °C. Unfoamed geopolymer (G-0) was prepared by a combination of sodium alkali, fly ash and slag. The PAS foam-to-paste ratio was set at 1.0 and 2.0 to prepare geopolymer foam (G-1 and G-2). Foamed geopolymer showed decreased compressive strength (25.1–32.0 MPa for G-1 and 21.5–36.2 MPa for G-2) compared to G-0 (36.9–43.1 MPa) at 29–1000 °C. Nevertheless, when compared to unheated samples, heated G-0 lost compressive strength by 8.7% up to 1000 °C, while the foamed geopolymer gained compressive strength by 68.5% up to 1000 °C. The thermal stability of foamed geopolymer was greatly improved due to the increased porosity, lower thermal conductivity, and incompact microstructure, which helped to reduce pressure during moisture evaporation and resulted in lessened deterioration.
  • Publication
    Effect of sodium aluminate on the fresh and hardened properties of fly ash-based one-part geopolymer
    ( 2021)
    Ooi Wan-En
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Ho Li Ngee
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Ong Shee-Ween
    ;
    Andrei Victor Sandu
    The one-part geopolymer binder was synthesis from the mixing of aluminosilicate material with solid alkali activators. The properties of one-part geopolymers vary according to the type and amount of solid alkali activators used. This paper presents the effect of various sodium metasilicate-to-sodium aluminate (NaAlO2/Na2SiO3) ratios on fly ash-based one-part geopolymer. The NaAlO2/Na2SiO3 ratios were set at 1.0 to 3.0. Setting time of fresh one-part geopolymer was examined through Vicat needle apparatus. Mechanical and microstructural properties of developed specimens were analysed after 28 days of curing in ambient condition. The study concluded that an increase in NaAlO2 content delayed the setting time of one-part geopolymer paste. The highest compressive strength was achieved at the NaAlO2/Na2SiO3 ratio of 2.5, which was 33.65 MPa. The microstructural analysis revealed a homogeneous structure at the optimum ratio. While the sodium aluminium silicate hydrate (N-A-S-H) and anorthite phases were detected from the XRD analysis.
      9  1
  • Publication
    Thermal insulation and mechanical properties in the presence of glas bubble in fly ash geopolymer paste
    ( 2021)
    Noor Fifinatasha Shahedan
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Norsuria Mahmed
    ;
    Liew Yun Ming
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Ikmal Hakem A Aziz
    ;
    Aeslina Abdul Kadir
    ;
    Andrei Victor Sandu
    ;
    Mohd Fathullah Ghazli@Ghazali
    The density, compressive strength, and thermal insulation properties of fly ash geopolymer paste are reported. Novel insulation material of glass bubble was used as a replacement of fly ash binder to significantly enhance the mechanical and thermal properties compared to the geopolymer paste. The results showed that the density and compressive strength of 50% glass bubble was 1.45 g/ ely, meeting the standard requirement for structural concrete. Meanwhile, the compatibility of 50% glass bubbles tested showed that the thermal conductivity (0.898 W/mK), specific heat (2.141 MJ/m3 K), and thermal diffusivity(0.572 mm2/s) in meeting the same requirement. The improvement of thermal insulation properties revealed the potential use of glass bubbles as an insulation material in construction material
      5  14