Heah Cheng Yong
Thumbnail Image
Preferred name
Heah Cheng Yong
Official Name
Heah, Cheng Yong
Alternative Name
Yong, Heah Cheng
Yong, H. C.
Heah, Cheng Yong
Heah, C. Y.
Cheng-Yong, Heah
Cheng Yong, Heah
Main Affiliation
Scopus Author ID
54402789500
Researcher ID
S-7139-2019

Research Output

Filters

69
Reset filters

Settings
Now showing 1 - 10 of 69
  • Publication
    Improvements of flexural properties and thermal performance in thin geopolymer based on fly ash and ladle furnace slag using borax decahydrates
    ( 2022)
    Ng Yong-Sing
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Phakkhananan Pakawanit
    ;
    Petrica Vizureanu
    ;
    Mohd Suhaimi Khalid
    ;
    Ng Hui-Teng
    ;
    Hang Yong-Jie
    ;
    Marcin Nabiałek
    ;
    Paweł Pietrusiewicz
    ;
    Sebastian Garus
    ;
    Wojciech Sochacki
    ;
    Agata Śliwa
    This paper elucidates the influence of borax decahydrate addition on the flexural and thermal properties of 10 mm thin fly ash/ladle furnace slag (FAS) geopolymers. The borax decahydrate (2, 4, 6, and 8 wt.%) was incorporated to produce FAB geopolymers. Heat treatment was applied with temperature ranges of 300 °C, 600 °C, 900 °C, 1000 °C and 1100 °C. Unexposed FAB geopolymers experienced a drop in strength due to a looser matrix with higher porosity. However, borax decahydrate inclusion significantly enhanced the flexural performance of thin geopolymers after heating. FAB2 and FAB8 geopolymers reported higher flexural strength of 26.5 MPa and 47.8 MPa, respectively, at 1000 °C as compared to FAS geopolymers (24.1 MPa at 1100 °C). The molten B2O3 provided an adhesive medium to assemble the aluminosilicates, improving the interparticle connectivity which led to a drastic strength increment. Moreover, the borax addition reduced the glass transition temperature, forming more refractory crystalline phases at lower temperatures. This induced a significant strength increment in FAB geopolymers with a factor of 3.6 for FAB8 at 900 °C, and 4.0 factor for FAB2 at 1000 °C, respectively. Comparatively, FAS geopolymers only achieved 3.1 factor in strength increment at 1100 °C. This proved that borax decahydrate could be utilized in the high strength development of thin geopolymers.
      3  21
  • Publication
    Preparation of Fly Ash-Ladle Furnace Slag Blended Geopolymer Foam via Pre-Foaming Method with Polyoxyethylene Alkyether Sulphate Incorporation
    ( 2022-06-01)
    Ng Hui Teng
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Rojviriya C.
    ;
    Razi H.M.
    ;
    Garus S.
    ;
    Nabiałek M.
    ;
    Sochacki W.
    ;
    Abidin I.M.Z.
    ;
    Ng Yong Sing
    ;
    Śliwa A.
    ;
    Sandu A.V.
    This paper uses polyoxyethylene alkyether sulphate (PAS) to form foam via pre-foaming method, which is then incorporated into geopolymer based on fly ash and ladle furnace slag. In the literature, only PAS-geopolymer foams made with single precursor were studied. Therefore, the performance of fly ash-slag blended geopolymer with and without PAS foam was investigated at 29–1000 °C. Unfoamed geopolymer (G-0) was prepared by a combination of sodium alkali, fly ash and slag. The PAS foam-to-paste ratio was set at 1.0 and 2.0 to prepare geopolymer foam (G-1 and G-2). Foamed geopolymer showed decreased compressive strength (25.1–32.0 MPa for G-1 and 21.5–36.2 MPa for G-2) compared to G-0 (36.9–43.1 MPa) at 29–1000 °C. Nevertheless, when compared to unheated samples, heated G-0 lost compressive strength by 8.7% up to 1000 °C, while the foamed geopolymer gained compressive strength by 68.5% up to 1000 °C. The thermal stability of foamed geopolymer was greatly improved due to the increased porosity, lower thermal conductivity, and incompact microstructure, which helped to reduce pressure during moisture evaporation and resulted in lessened deterioration.
      1
  • Publication
    Effect of anisotropic pores on the material properties of metakaolin geopolymer composites incorporated with corrugated fiberboard and rubber
    ( 2021-09-01)
    Nur Ain Jaya
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Foo Wah L.
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Zainal Abidin I.M.
    ;
    Azaman N.
    ;
    Ooi Wan-En
    This paper compares the compressive strength and thermal conductivity of metakaolin geopolymer (MKG) incorporated with anisotropic and isotropic pores. MKG was prepared by activation with sodium hydroxide and sodium silicate. Corrugated fiberboard and rubber were included to create anisotropy of pores, and they were added in 3, 5, and 7 layers. Hydrogen peroxide and surfactant were added to generate isotropic pores. For geopolymer with corrugated fiberboard (MKG-C) and rubber (MKG-R), compressive test and thermal conductivity measurement were performed in perpendicular and parallel direction to the flat surface of fiberboard and rubber. The result showed that MKG-C and MKG-R exhibited mechanical and insulation anisotropically. The highest compressive strength was achieved in the parallel loading direction while the lowest thermal conductivity was attained in the perpendicular direction. MKG-C possessed better compressive strength of 26.9 MPa loaded in the parallel direction. The compressive strength performance of MKG-C was greater than MKG-R because of the fibrous-like structure, which further contributes to the strength. The thermal conductivity was low (0.15–0.20 W/mK) for both MKG-C and MKG-R. The anisotropy of pores led to high strength retention and improvement of thermal insulating properties. These properties were contrary to geopolymer with isotropic pores (MKG-F), which have excellent thermal insulating properties but low compressive strength to be eligible for structural applications.
      1
  • Publication
    Elevated-temperature performance, combustibility and fire propagation index of fly ash-metakaolin blend geopolymers with addition of monoaluminium phosphate (MAP) and aluminum dihydrogen triphosphate (ATP)
    ( 2021-04-02)
    Khairunnisa Zulkifly
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Bayuaji R.
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Ahmad S.B.
    ;
    Stachowiak T.
    ;
    Szmidla J.
    ;
    Gondro J.
    ;
    Jeż B.
    ;
    Khalid M.S.B.
    ;
    Garus S.
    ;
    Ong Shee-Ween
    ;
    Ooi Wan-En
    ;
    Ng Hui-Teng
    Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FAMK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(H2PO4)3), and monoaluminium phosphate, MAP (AlPO4) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0–3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure. Besides, combustibility and fire propagation tests were conducted to examine the thermal performance and the applicability of the geopolymers as passive fire protection. Experimental results revealed that the blended geopolymers with 1 wt.% of ATP and MAP exhibited higher compressive strength and denser geopolymer matrix than control geopolymers. The effect of ATP and MAP addition was more obvious in unheated geopolymer and little improvement was observed for geopolymer subjected to elevated temperature. ATP and MAP at 3 wt.% did not help in enhancing the elevated-temperature performance of blended geopolymers. Even so, all blended geopolymers, regardless of the addition of ATP and MAP, were regarded as the noncombustible materials with negligible (0–0.1) fire propagation index.
      2  18
  • Publication
    Elevated-Temperature performance, combustibility and fire propagation index of Fly Ash-Metakaolin blend geopolymers with addition of Monoaluminium Phosphate (MAP) and Aluminum Dihydrogen Triphosphate (ATP)
    ( 2021)
    Khairunnisa Zulkifly
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    ;
    Ridho Bayuaji
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Shamsul Bin Ahmad
    ;
    Tomasz Stachowiak
    ;
    Janusz Szmidla
    ;
    Joanna Gondro
    ;
    Bartłomiej Jeż
    ;
    Mohd Suhaimi Bin Khalid
    ;
    Sebastian Garus
    ;
    Ong Shee-Ween
    ;
    Ooi Wan-En
    ;
    Ng Hui-Teng
    Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FA-MK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(H2PO4)3), and monoaluminium phosphate, MAP (AlPO4) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0–3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure. Besides, combustibility and fire propagation tests were conducted to examine the thermal performance and the applicability of the geopolymers as passive fire protection. Experimental results revealed that the blended geopolymers with 1 wt.% of ATP and MAP exhibited higher compressive strength and denser geopolymer matrix than control geopolymers. The effect of ATP and MAP addition was more obvious in unheated geopolymer and little improvement was observed for geopolymer subjected to elevated temperature. ATP and MAP at 3 wt.% did not help in enhancing the elevated-temperature performance of blended geopolymers. Even so, all blended geopolymers, regardless of the addition of ATP and MAP, were regarded as the noncombustible materials with negligible (0–0.1) fire propagation index.
      1  23
  • Publication
    Cold-pressed fly ash geopolymers: effect of formulation on mechanical and morphological characteristics
    ( 2021)
    Ong Shee-Ween
    ;
    Heah Cheng Yong
    ;
    Lynette Wei Ling Chan
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Ho Li Ngee
    ;
    Liew Yun Ming
    ;
    Ooi Wan-En
    ;
    Ng Yong-Sing
    ;
    Nur Ain Jaya
    This research uses low alkali activator content and cold pressing technique for fly ash-based geopolymers formation under room temperature condition. The geopolymers were prepared using four different parameters: fly ash/alkali activator ratio, sodium hydroxide concentration, sodium silicate/sodium hydroxide ratio and pressing force. The results indicated that the compressive strength (114.2 MPa) and flexural strength (29.9 MPa) of geopolymers maximised at a fly ash/alkali activator ratio of 5.5, a 14 M sodium hydroxide concentration, a sodium silicate/sodium hydroxide ratio of 1.5 and a pressing force of 5 tons (pressing stress of 100.0 MPa and 155.7 MPa for compressive and flexural samples, respectively). The degree of reaction (40.1%) enhanced the structure compactness with minimum porosity. The improved mechanical properties confirmed that a high strength pressed geopolymer could be formed at low alkali activator content without the aid of temperature.
      1  36
  • Publication
    Improvements of Flexural Properties and Thermal Performance in Thin Geopolymer Based on Fly Ash and Ladle Furnace Slag Using Borax Decahydrates
    ( 2022-06-01)
    Ng Yong-Sing
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Pakawanit P.
    ;
    Vizureanu P.
    ;
    Khalid M.S.
    ;
    Ng Hui-Teng
    ;
    Hanh Yong-Jie
    ;
    Nabiałek M.
    ;
    Pietrusiewicz P.
    ;
    Garus S.
    ;
    Sochacki W.
    ;
    Śliwa A.
    This paper elucidates the influence of borax decahydrate addition on the flexural and thermal properties of 10 mm thin fly ash/ladle furnace slag (FAS) geopolymers. The borax decahydrate (2, 4, 6, and 8 wt.%) was incorporated to produce FAB geopolymers. Heat treatment was applied with temperature ranges of 300◦C, 600◦C, 900◦C, 1000◦C and 1100◦C. Unexposed FAB geopolymers experienced a drop in strength due to a looser matrix with higher porosity. However, borax decahydrate inclusion significantly enhanced the flexural performance of thin geopolymers after heating. FAB2 and FAB8 geopolymers reported higher flexural strength of 26.5 MPa and 47.8 MPa, respectively, at 1000◦C as compared to FAS geopolymers (24.1 MPa at 1100◦C). The molten B2O3 provided an adhesive medium to assemble the aluminosilicates, improving the interparticle connectivity which led to a drastic strength increment. Moreover, the borax addition reduced the glass transition temperature, forming more refractory crystalline phases at lower temperatures. This induced a significant strength increment in FAB geopolymers with a factor of 3.6 for FAB8 at 900◦C, and 4.0 factor for FAB2 at 1000◦C, respectively. Comparatively, FAS geopolymers only achieved 3.1 factor in strength increment at 1100◦C. This proved that borax decahydrate could be utilized in the high strength development of thin geopolymers.
      1
  • Publication
    Evaluation of flexural properties and characterisation of v10-mm thin geopolymer based on fly ash and ladle furnace slag
    ( 2021-11-01)
    Yong-Sing N.
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Chan L.W.L.
    ;
    Hui-Teng N.
    ;
    Shee-Ween O.
    ;
    Wan-En O.
    ;
    Yong-Jie H.
    The formulation and flexural properties of thin fly ash geopolymers with thickness of merely 10 mm and replacement of ladle furnace slag to fly ash in thin geopolymer were presented. The formulation was discussed in terms of NaOH molarity, solid aluminosilicates-to-liquid alkali activator (S/L) mass ratio, and alkali activator (Na2SiO3/NaOH) mass ratio. Thin fly ash geopolymers with flexural strength and Young's modulus of 6.2 MPa and 0.14 GPa, respectively, were obtained by using 12 M NaOH, S/L ratio of 2.5 and Na2SiO3/NaOH ratio of 4.0. A high Na2SiO3/NaOH ratio was implemented for thin geopolymer synthesis to produce a more viscous slurry which helped to retain the shape of a thin geopolymer. The incorporation of ladle furnace slag up to 40 wt.% reported an increment of 26% in flexural strength up to 7.8 MPa as compared to pure fly ash geopolymers and the stiffness was increased to 0.19 GPa. Denser microstructure with improved compactness was observed as the ladle furnace slag acted as the filler. New crystalline phases of calcium silicate hydrate (C–S–H) were formed and coexisted with the geopolymer matrix, which consequently enhanced the flexural strength of thin fly ash geopolymer. This proved that the ladle furnace slag has the potential to be utilised in geopolymer synthesis and will enhance the flexural properties of thin geopolymers. The flexural performance of thin geopolymers in this study was considerably good as the thin geopolymers exhibited comparatively similar flexural strengths, but a higher strength/thickness ratio as compared to geopolymers with thickness greater than 40 mm.
      1  19
  • Publication
    Functionalized Carbon Nanotube-Modified ELISA for Early Detection of Heart Attack
    ( 2023-12-01)
    Chow E.M.Y.
    ;
    Foo Kai Loong
    ;
    Subash Chandra Bose Gopinath
    ;
    Tan Soo Jin
    ;
    Kashif M.
    ;
    Heah Cheng Yong
    ;
    Liew Yun Ming
    A warning issue of heart attacks in young adults needs immediate attention lately. Enzyme-linked immunosorbent assay (ELISA) is an easy and commonly used method for detecting early stages of heart attack. Cardiac troponin I (cTnI) is a responsible biomarker for acute myocardial infarction. However, the conventional ELISA system was only able to detect at 100 pM of cTnI. To improve the system, enhancements were introduced through the integration of functionalized carbon nanotube (fCNT) to amplify cTnI detection signals. By utilizing the advantage of fCNT, a noticeable improvement in results can be obtained. The detection limit was lowered down to an impressive 10 pM. Furthermore, the change of absorbance increased from 31.90% for conventional ELISA surge to 98.61 for modified ELISA system. This three-fold increase in sensitivity shows remarkable improvement through the introduction of fCNT in modified ELISA technique.
      1
  • Publication
    Properties of polyaniline/graphene oxide (PANI/GO) composites: effect of GO loading
    ( 2021-09-01)
    Mutalib T.N.A.B.T.A.
    ;
    Tan Soo Jin
    ;
    Foo Kai Loong
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Mohd. Mustafa Al Bakri Abdullah
    Polyaniline/graphene oxide (PANI/GO) composites at different wt% of GO were prepared via solution method. PANI was mixed with the GO synthesized from the improved Hummer’s method. The formation of GO was confirmed via Raman and C/O ratio. Based on the FT-IR, XRD and SEM results, it confirmed the presence of both PANI and GO characteristics at 10.9°, 25.8° and 27.8° and interactions between PANI and GO particles in PANI/GO composites at different GO loading. SEM micrographs showed a folding and wrinkled surface of GO due to the defect upon oxidation process. This means that the weak π–π interactions or the agglomeration of GO have caused PANI unable to attach on the large conjugated basal planes of GO sheets. The defective domains made GO as an insulator as it contained distortions and oxygen-containing functional groups and their local decoration. Low-conductivity domain had conquered most of the GO region which later reduced the pathway of the current flow; therefore, conductivity is affected. The wrinkled structure also resulted in the low conductivity as it weakens the interfacial interaction between PANI and GO and thus disrupted the electron movement in the composites. Due to this, the electrical conductivity reached up to 1.83 × 10−10 S/cm as the GO loading increased to 50 wt%.
      2