Shahriman Abu Bakar

Shahriman Abu Bakar

Preferred name

Shahriman Abu Bakar

Official Name

Shahriman, Abu Bakar

Alternative Name

Bakar, Shahriman A.B.

Shariman, A. B.

Ab, Shahriman

Abu Bakar, S.

Bakar, A. S.

Bakar, S. A.

Bakar, Shahriman Abu

Bakar, Sharifah Adzila Syed Abu

Bakar, S. Abu

Main Affiliation

Universiti Malaysia Perlis

Scopus Author ID

57196198202

Researcher ID

ELT-0087-2022

Now showing 1 - 7 of 7

Engine performance enhancement by improving heat transfer in between exhaust valve and valve seat through CFD (transient thermal) simulation

( 2021-05-03)
Mohamad Aniq Syazwan Mohamed Hassan
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Nur Saifullah Kamarrudin
;
Aziz I.A.
;
Wan Khairunizam Wan Ahmad
;
Mohd Sani Mohamad Hashim
;
Azizi Harun
;
Ishak Ibrahim
;
Ibrahim Z.
;
Mohd Khairul Faizi Abd Rahman
;
Muhammad Faiz Hilmi Rani
;
Rishan Murali

The combustion of the internal combustion engine results in high heat and pressure produce as exhaust gas. The high-temperature exhaust gas will transfer the heat to surrounding via convection, conduction, and radiation. In the combustion chamber, the exhaust valve and its seat will reach high temperatures due to hot gases exit through the engine exhaust port. This high temperature must be reduced to avoid damaging the engine. In this project, the existing material of the valve seat is tested using computational fluid dynamics simulation for heat analysis. Simulation of transient thermal is conducted to study the detailed behavior of heat transfer of the valve and valve seat in the engine. Four copper-based material of the valve seat is selected which is beryllium copper, chromium copper, brass, bronze are simulated. In the simulation, the brass valve seat has the highest heat absorbance rate which averagely 30% higher than cast iron valve seat in terms of temperature differences. Most of the copper-based valve seat can absorb averagely 10% to 30% more heat than cast iron valve seat depends on the material's thermal conductivity.

3
Investigating the thermal characteristic of copper alloys valve seat towards engine performance enhancement of MODENAS CT115 through steady-state analysis

( 2021-10-25)
Zainol M.A.A.
;
Mohamad Aniq Syazwan Mohamed Hassan
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Anas Abdul Rahman
;
Mohd Sani Mohamad Hashim
;
Nur Saifullah Kamarrudin
;
Wan Khairunizam Wan Ahmad
;
Azizi Harun
;
Ishak Ibrahim
;
Mohd Khairul Faizi Abd Rahman
;
Muhammad Faiz Hilmi Rani

MODENAS CT115 engine is a single overhead camshaft (SOHC) engine, with a rated power of 8.8 horsepower at 9000 rpm. One of the main concerns of engine research is the overheating of engines. Overheating can affects the performance of an engine by leading to a loss of strength and thermal strain. To prevent failure, thermal analysis is used to determine the flow of heat with precision to optimise temperature distribution. The investigation is done using ANSYS Thermal simulation on the CAD model of the engine cylinder head, intake and exhaust valve, and intake and exhaust valve seat insert. The comparison to the existing valve seat insert is made using three different valve seat insert materials: Beryllium-copper C17200, Bronze-copper C61300, and Brass C36000. The research results proved that Brass C36000 provides the best thermal reduction and heat transfer increment compared to the existing valve seat insert material.

2 1
Improvement of Dissolved Oxygen in Perlis River based on Various Aeration Systems

( 2021-12-14)
Muhammad Faiz Hilmi Rani
;
Nur Saifullah Kamarrudin
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Wan Khairunizam Wan Ahmad
;
Mohd Sani Mohamad Hashim
;
Ishak Ibrahim
;
Anas Abdul Rahman
;
Ibrahim Z.
;
Mohd Khairul Faizi Abd Rahman
;
Mohamad Aniq Syazwan Mohamed Hassan
;
Abd Manap A.A.
;
Zainuddin I.F.

Water pollution is closely related to the Water Quality Index (WQI). One of the parameters in classifying WQI is dissolved oxygen (DO) that can be improved by introducing the surface and subsurface aerations. Herein, the Perlis River's water quality was investigated by evaluating the DO's improvement based on various aeration systems. The changes of DO (mg/L) and DO improvement (%) were evaluated during both low and high tide conditions. A total of 9 sets of data collection had been studied by comparing base DO (without running of aeration) and measured DO (with running of aeration) of river. The DO sensor was used to measure the changes of DO in the aeration measurement system. Results found that the DO improvement managed to achieve 74.89%, 10.18%, 35.58%, and 52.45% for water jet, air compressor, commercial venturi, and DIY venturi, respectively. Besides, different behaviour of DO's improvement was observed during low and high tide conditions.

2
CFD Simulation on Improving Water Quality based on Various Aerator Models to Demonstrate Cost Performance Analysis

( 2021-12-14)
Nazrul Najmi Norbashah
;
Muhammad Faiz Hilmi Rani
;
Nur Saifullah Kamarrudin
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Wan Khairunizam Wan Ahmad
;
Mohd Sani Mohamad Hashim
;
Ishak Ibrahim
;
Anas Abdul Rahman
;
Ibrahim Z.
;
Mohd Khairul Faizi Abd Rahman
;
Mohamad Aniq Syazwan Mohamed Hassan
;
Abd Manap A.A.
;
Zainuddin I.F.

There are many types of aerator that can be used to perform a water treatment process either from air to water or from water to air approaches. Other than focusing on the performance itself, the usage cost of aerator should be forecasted in detail too to have a sustainable and economical method in remediating the polluted water. Therein, the cost performance analysis was demonstrated by performing a computational fluid dynamics (CFD) simulation on improving water quality based on various aerator models. The simulation was focused in a small-scale aeration tank that consists of a mixing chamber, air duct, and a few of bubble diffusers. The improvement of water quality was assessed by calculating the number of gas bubble particles produced by 4 different configurations of aerator model, namely aerator model A, B, C and D, respectively. Results found that the aerator model D (5 bubble diffuser at 620 L/min) produces the highest number of gas particles up to 72.2%. However, the aerator model C (5 bubble diffuser at 300 L/min) was found to achieve the most efficient and sustainable approach based on energy consuming and cost of aerator configuration when compared to the other aerator models.

2
Engine Performance Analysis by Studying Heat Transfer in the Valve Seat through Steady-State Thermal Simulation

( 2021-12-14)
Mohamad Aniq Syazwan Mohamed Hassan
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Nur Saifullah Kamarrudin
;
Wan Khairunizam Wan Ahmad
;
Mohd Sani Mohamad Hashim
;
Azizi Harun
;
Ishak Ibrahim
;
Azizul Aziz I.
;
Zunaidi Ibrahim
;
Mohd Khairul Faizi Abd Rahman
;
Muhammad Faiz Hilmi Rani
;
Anas Abdul Rahman
;
Mohd Afendi Rojan
;
Rishan Murali

As the engine reached high speed, the exhaust valve temperature increased exponentially due to the exhaust gas produced by the combustion process between the mixture of air and fuel within the combustion chamber of the internal combustion engine. The valve is subjected to thermal loading due to high temperature and pressure within the cylinder, which must withstand a material temperature for sustainable and optimal operation. To avoid this loss, a perfect medium must be prepared to ensure that the heat is extracted smoothly. This can be done when the valve is in contact with the seat and there is a periodic heat transfer contact. Therefore, it is imperative to research the correlation between valve and valve seat to understand the two sections' heat transfer mechanism. In this study, thermal contact analysis was used to identify heat transfer between the valve and the valve seat as both parts are interconnected. This research also has an interest in studying the two surface conduction mechanisms as the exhaust valve closed in steady-state conditions. Thus, this study portrays a significant method, particularly for the determining the distribution of temperature, heat flux, and heat flux direction between the valve and its seat using ANSYS Workbench.

2
Investigating and improving Boeing aircraft composite panel industrial painting issues by designing smart robotic precision painting system

( 2021-10-25)
Mohamad Aniq Syazwan Mohamed Hassan
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Nur Saifullah Kamarrudin
;
Mohd Sani Mohamad Hashim
;
Wan Khairunizam Wan Ahmad
;
Azizi Harun
;
Ishak Ibrahim
;
Mohd Khairul Faizi Abd Rahman
;
Fadzilla M.A.
;
Rahman M.F.A.
;
Hamid N.M.F.N.A.
;
Manaf A.A.
;
Rani M.F.H.

Aerospace Composites Malaysia (ACM) Sdn Bhd produces one of the aircraft components, which is an aircraft composite panel. Currently, the painting of the composite aircraft panel is manually conducted by the high skilled human operator. However, there are several issues of manual painting, which are the precision of the thickness specifications, uneven spray, dust-free, microbubble, colour appearance, and contour of the aircraft composite panel. Consequently, these issues contribute to the aircraft aerodynamic performances, productivity, and index time of the aircraft composite panel's production. Thus, the main objectives are to investigate the human painting mimicking robot incorporated with the existing painting environment. The proposed environment becomes smart precision painting systems. In conclusion, the proposed prototype will overcome the quality issue of aircraft composite panel painting faced by Boeing worldwide aircraft industries. Furthermore, the proposed prototype will increase productivity and contribute to the maintaining of the aircraft's aerodynamic performance.

2 2
Development of a Novel Aeration Measurement System to Evaluate Water Treatment Process in a River

( 2021-12-14)
Muhammad Faiz Hilmi Rani
;
Nur Saifullah Kamarrudin
;
Shahriman Abu Bakar
;
Zuradzman Mohamad Razlan
;
Wan Khairunizam Wan Ahmad
;
Mohd Sani Mohamad Hashim
;
Ishak Ibrahim
;
Anas Abdul Rahman
;
Ibrahim Z.
;
Mohd Khairul Faizi Abd Rahman
;
Mohamad Aniq Syazwan Mohamed Hassan
;
Abd Manap A.A.
;
Zainuddin I.F.

A novel aeration measurement system was developed to evaluate the water treatment process in a river to acquire a more comparable dissolved oxygen value even if various types of aerations are tested. The system comprises of DO sensor, water flowmeter, anemometer, PVC pipes, water pump, air compressor pump, and truck tyre tubes. The PVC pipes consisting of a main drainage hole, 5 holes for dissolve oxygen data collection, 1 hole as the location of aerator system, and connectors were designed as the major part of the system by using Computer Aided Design software. The main drainage hole (horizontal pipe) was designed to be 288.5 cm in length, while the measured holes (vertical pipes) were designed to be 45.7 cm in height. By considering a systematic approach, the designed system is hopefully able to solve measuring issue of dissolved oxygen in moving water and to provide a better evaluation of water treatment process.

3

Shahriman Abu Bakar

Research Output

Filters

Author

Organization

Funding

Has files

Type

Settings

Sort By

Results per page

Options

Shahriman Abu Bakar

Research Output

Filters

Author

Organization

Funding

Has files

Type

Settings

Sort By

Results per page