Uda Hashim
Thumbnail Image
Preferred name
Uda Hashim
Official Name
Uda, Hashim
Alternative Name
Hashimb, U.
Hashim, Uda
Hashim, U.
Uda, Hashim
Main Affiliation
Scopus Author ID
22633937800
Researcher ID
CVC-6955-2022

Research Output
Now showing 1 - 5 of 5
Thumbnail Image
Publication

Aluminium interdigitated electrode with 5.0 μm gap for electrolytic scooting

2024-06 , Uda Hashim , Muhammad Nur Aiman Uda , Tijjani Adam , Asral Bahari Jambek , Ismail Saad , Nor Azizah Parmin , Shahidah Arina Shamsuddin , Nursakinah Abdul Karim , G. Yashni , Nur Hulwani Ibrahim , N. Parimon , M. F. H. Rani

The goal of the research project is to design, fabricate, and characterize an extremely sensitive biosensor for use in healthcare. Using AutoCAD software, a novel IDE pattern with a 5 μm finger gap was created. Conventional photolithography and regular CMOS technology were used in the fabrication process. A 3D nano profiler, scanning electron microscopy (SEM), high-power microscopy (HPM), and low-power microscopy (LPM) were used to physically characterize the manufactured IDE. Chemical testing was done using several pH buffer solutions, and electrical validation was performed using I-V measurements. The Al IDE was produced, with a tolerance of 0.1 μm between the fabricated IDEs and the design mask. Electrical measurements verified the flawless fabrication of the IDE, and the device's repeatability was validated by the outcomes of comparable IDE samples. For each pH buffer solution, a modest additional volume of 2 μl was used to quantitatively detect slight current fluctuations in the microampere range. Through pH calibration for advanced applications in the realm of chemical sensors using an amperometric method, this research study has verified the chemical behavior of the IDE.

View
Thumbnail Image
Publication

Fabrication of silicon nanowire sensors for highly sensitive pH and DNA hybridization detection

2022 , Siti Fatimah Abd Rahman , Nor Azah Yusof , Mohd Khairuddin Md Arshad , Uda Hashim , Mohammad Nuzaihan Md Nor , Mohd Nizar Hamidon

A highly sensitive silicon nanowire (SiNW)-based sensor device was developed using electron beam lithography integrated with complementary metal oxide semiconductor (CMOS) technology. The top-down fabrication approach enables the rapid fabrication of device miniaturization with uniform and strictly controlled geometric and surface properties. This study demonstrates that SiNW devices are well-aligned with different widths and numbers for pH sensing. The device consists of a single nanowire with 60 nm width, exhibiting an ideal pH responsivity (18.26 × 106 Ω/pH), with a good linear relation between the electrical response and a pH level range of 4–10. The optimized SiNW device is employed to detect specific single-stranded deoxyribonucleic acid (ssDNA) molecules. To use the sensing area, the sensor surface was chemically modified using (3-aminopropyl) triethoxysilane and glutaraldehyde, yielding covalently linked nanowire ssDNA adducts. Detection of hybridized DNA works by detecting the changes in the electrical current of the ssDNA-functionalized SiNW sensor, interacting with the targeted ssDNA in a label-free way. The developed biosensor shows selectivity for the complementary target ssDNA with linear detection ranging from 1.0 × 10−12 M to 1.0 × 10−7 M and an attained detection limit of 4.131 × 10−13 M. This indicates that the use of SiNW devices is a promising approach for the applications of ion detection and biomolecules sensing and could serve as a novel biosensor for future biomedical diagnosis.

View
Thumbnail Image
Publication

Electrical simulation on silicon nanowire field-effect transistor biosensor at different substrate-gate voltage bias conditions for charge detection

2022-12 , X.Y. Teoh , Mohamad Faris Mohamad Fathil , Y.M.Tan , Norhayati Sabani , Mohammad Nuzaihan Md Nor , Mohd Khairuddin Md Arshad , Ruslinda A. Rahim , Nur Hamidah Abdul Halim , Ramzan Mat Ayub , Uda Hashim , M.M. Ibrahim

In this work, the impact of different substrate-gate voltage bias conditions (below and above the device threshold voltage) on current-voltage characteristics and sensitivity of a silicon nanowire field-effect transistor (SiNW-FET) biosensor was investigated. A 3-dimensional device structure with n-type SiNW channel and a substrate gate electrode was designed and electrically simulated In the Silvaco ATLAS. Next, the SiNW channel was covered with a range of interface charge density to mimic the charged target biomolecule captured by the device. The outcome was translated into a drain current versus interface charge semi-log graph and the device sensitivity was calculated using the linear regression curve’s slope of the plotted data. The device’s electrical characteristic shown higher generation of output drain current values with the increase of negative substrate-gate voltage bias due to the hole carriers’ accumulation that forms a conduction channel in the SiNW. Application of higher negative interface charge density increased the change in drain current, with the device biased with higher substrate-gate voltage shows more significant change in drain current. The device sensitivity increased when biased with higher substrate-gate voltage with highest sensitivity is 75.12 nA/dec at substrate-gate voltage bias of –1.00 V.

View
Thumbnail Image
Publication

Advancing COVID-19 detection high-performance RNA biosensing via electrical interactions

2024-06 , Uda Hashim , Muhammad Nur Afnan Uda , Muhammad Nur Aiman Uda , Tijjani Adam , Nur Hulwani Ibrahim , Chai Chang Yii , Lorita Angeline

This research paper investigated the detection of COVID-19 using an Aluminum Interdigitated Electrode (Al-IDE) sensor based on electrical conductivity. The silanization process involved the functionalization step, employing (3-Aminopropyl) triethoxysilane (APTES), while the immobilization process was facilitated by the RNA Probe specific to COVID-19. To verify its specificity in detection, the functionalized biosensor was tested against single-base mismatches, non-complementary sequences, and complementary sequences. The physical characteristics of the Al-IDE biosensor were examined using both low-power microscopy (LPM) and high-power microscopy (HPM). Additionally, the morphological properties of the biosensor were assessed using atomic force microscopy (AFM). To assess its diagnostic potential, the biosensor's sensitivity was evaluated by exposing it to a range of complementary targets, spanning from 1 femtomolar (fM) to 1 micromolar (μM). The current-voltage (I-V) characteristics of the biosensor were meticulously analyzed at each stage of functionalization bare Al-IDE, silanization, immobilization, and hybridization. This I-V characterization was carried out using a picoammeter voltage source (Keithley 2450), Kickstart software, and a probe station. The results confirmed the biosensor's capability to effectively detect COVID-19 targets within the nanoampere concentration range, demonstrating its success in detecting specific COVID-19 targets at the nanoampere level.

View
Thumbnail Image
Publication

Gold-nanoparticle associated deep eutectic solution mediates early bio detection of ovarian cancer

2025-01 , S. Uvambighai Devi , Nor Azizah Parmin , N. Fareezah Jaapar , F. Syakirah Halim , Uda Hashim , Subash Chandra Bose Gopinath , Muhammad Nur Aiman Uda , Voon Chun Hong , Mohammad Nuzaihan Md Nor , Adilah Ayoib , Shahidah Arina Shamsuddin , Norizah Abd Karim

Gold nanoparticles (AuNPs) have indeed been extensively researched in biological and photothermal therapy applications in recent years. This study aims to enhance the sensitivity of biosensors for early detection of ovarian cancer biomarkers by investigating the efficacy of DES-mediated surface functionalization of AuNPs. Additionally, the impact of DES on the stability and dispersion of AuNPs on SiO2 support is assessed to optimize sensor performance. A simple DES-mediated synthesis method for efficient amine surface functionalization of silicon dioxide (SiO2) to incorporate tiny AuNPs for antibody biosensors. Physical characterization [Scanning Electron Microscope (SEM), Ultraviolet-Visible Spectrophotometer (UV-Vis), Fourier Transform Infrared Spectroscopy (FTIR), and 3D Profiler] and electrical characterization (Keithley) have been done to determine the functionalization of the modified IDE surface. SEM analysis indicated the resultant nanoparticles have truncated spherical shapes. There is just a peak recorded by UV-Vis at 504-540 nm with AuNPs due to the formation of monodispersed AuNPs. When the conjugation of DES with samples is measured, the curves are identical in form, and the highest peak after conjugation has remained at 230 nm but the SPR absorption peak becomes narrower and moves toward greater wavelengths, indicating the conjugation between the molecules. Furthermore, when the DES is conjugated with AuNPs, 3-Aminopropyltriethoxysilane (APTES), antibody, and protein, the peaks gradually increased and became narrower, where O-H at 3280 cm-1, C-H at 2809 cm-1 and 2933 cm-1, CH2 at 1448 cm-1, CH3 at 1268 cm-1, C-OH at 1048 cm-1 and 1110 cm-1 and C-N+ at 844 cm-1 as analyzed by FTIR. Moreover, it can be observed that the 3D profilometer revealed a few red-colored areas, which are the portion that protrudes from the IDE surface. Based on the findings, it is possible to infer that this immunosensor does have the prospective to be used in clinical investigations for the precise detection of ovarian cancer or other biomarkers. The capacitance, transmittance, and resistivity profiles of the biosensor clearly distinguished between the antibody immobilization and the affinity binding. The presence of a DES-mediated synthetic approach increased the possibility of supporting different metal nanoparticles on SiO2 as the potential platform for biosensor applications.

View