Mohd. Mustafa Al Bakri Abdullah
Thumbnail Image
Preferred name
Mohd. Mustafa Al Bakri Abdullah
Official Name
Abdulah, Mohd. Mustafa Al Bakri
Alternative Name
Abdullah, M.M.A.
M.M.A. Abdullah
Mustafa Al Bakri, A. M.
Albakri Abdullah, M. M.
Main Affiliation
CeGeoGTech UniMAP
Scopus Author ID
53164519100

Filters

Reset filters

Settings
Now showing 1 - 4 of 4
  • Publication
    Effects of multiple reflow on the formation of primary crystals in Sn-3.5Ag and solder joint strength: experimental and finite element analysis
    ( 2023)
    Siti Farahnabilah Muhd Amli
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Mohd Sharizal Abdul Aziz
    ;
    Hideyuki Yasuda
    ;
    Kazuhiro Nogita
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Ovidiu Nemes
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    The growth and formation of primary intermetallics formed in Sn-3.5Ag soldered on copper organic solderability preservative (Cu-OSP) and electroless nickel immersion gold (ENIG) surface finish after multiple reflows were systematically investigated. Real-time synchrotron imaging was used to investigate the microstructure, focusing on the in situ growth behavior of primary intermetallics during the solid–liquid–solid interactions. The high-speed shear test was conducted to observe the correlation of microstructure formation to the solder joint strength. Subsequently, the experimental results were correlated with the numerical Finite Element (FE) modeling using ANSYS software to investigate the effects of primary intermetallics on the reliability of solder joints. In the Sn-3.5Ag/Cu-OSP solder joint, the well-known Cu6Sn5 interfacial intermetallic compounds (IMCs) layer was observed in each reflow, where the thickness of the IMC layer increases with an increasing number of reflows due to the Cu diffusion from the substrate. Meanwhile, for the Sn-3.5Ag/ENIG solder joints, the Ni3Sn4 interfacial IMC layer was formed first, followed by the (Cu, Ni)6Sn5 IMC layer, where the formation was detected after five cycles of reflow. The results obtained from real-time imaging prove that the Ni layer from the ENIG surface finish possessed an effective barrier to suppress and control the Cu dissolution from the substrates, as there is no sizeable primary phase observed up to four cycles of reflow. Thus, this resulted in a thinner IMC layer and smaller primary intermetallics, producing a stronger solder joint for Sn-3.5Ag/ENIG even after the repeated reflow process relative to the Sn-3.5Ag/Cu-OSP joints.
      14  37
  • Publication
    Effect of the sintering mechanism on the crystallization kinetics of Geopolymer-Based ceramics
    ( 2023)
    Nur Bahijah Mustapa
    ;
    Romisuhani Ahmad
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Wan Mastura Wan Ibrahim
    ;
    Andrei Victor Sandu
    ;
    Ovidiu Nemes
    ;
    Petrica Vizureanu
    ;
    Christina W. Kartikowati
    ;
    Puput Risdanareni
    This research aims to study the effects of the sintering mechanism on the crystallization kinetics when the geopolymer is sintered at different temperatures: 200 °C, 400 °C, 600 °C, 800 °C, 1000 °C, and 1200 °C for a 3 h soaking time with a heating rate of 5 °C/min. The geopolymer is made up of kaolin and sodium silicate as the precursor and an alkali activator, respectively. Characterization of the nepheline produced was carried out using XRF to observe the chemical composition of the geopolymer ceramics. The microstructures and the phase characterization were determined by using SEM and XRD, respectively. The SEM micrograph showed the microstructural development of the geopolymer ceramics as well as identifying reacted/unreacted regions, porosity, and cracks. The maximum flexural strength of 78.92 MPa was achieved by geopolymer sintered at 1200 °C while the minimum was at 200 °C; 7.18 MPa. The result indicates that the flexural strength increased alongside the increment in the sintering temperature of the geopolymer ceramics. This result is supported by the data from the SEM micrograph, where at the temperature of 1000 °C, the matrix structure of geopolymer-based ceramics starts to become dense with the appearance of pores.
      3  24
  • Publication
    Effect of sintering mechanism towards crystallization of geopolymer ceramic - a review
    (MDPI, 2023-05-31)
    Nur Bahijah Mustapa
    ;
    Romisuhani Ahmad
    ;
    Wan Mastura Wan Ibrahim
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Nuttawit Wattanasakulpong
    ;
    Ovidiu Nemeș
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    ;
    Ioan Gabriel Sandu
    ;
    Christina W. Kartikowati
    ;
    Puput Risdanareni
    Globally, there is an increasing need for ceramic materials that have a variety of applications in the environment, for precision tools, and for the biomedical, electronics, and environmental industries. However, in order to obtain remarkable mechanical qualities, ceramics have to be manufactured at a high temperature of up to 1600 °C over a long heating period. Furthermore, the conventional approach presents issues with agglomeration, irregular grain growth, and furnace pollution. Many researchers have developed an interest in using geopolymer to produce ceramic materials, focusing on improving the performances of geopolymer ceramics. In addition to helping to lower the sintering temperature, it also improves the strength and other properties of the ceramics. Geopolymer is a product of polymerization involving aluminosilicate sources such as fly ash, metakaolin, kaolin, and slag through activation using an alkaline solution. The sources of the raw materials, the ratio of the alkaline solution, the sintering time, the calcining temperature, the mixing time, and the curing time may have significant impacts on the qualities. Therefore, this review aims to study the effects of sintering mechanisms on the crystallization of geopolymer ceramics, concerning the strength achieved. A future research opportunity is also presented in this review.
      8  25
  • Publication
    Recent developments in steelmaking industry and potential alkali activated based steel waste: A comprehensive review
    ( 2022)
    Ikmal Hakem Aziz
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Liew Yun Ming
    ;
    Long Yuan Li
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    ;
    Ovidiu Nemes
    ;
    Shaik Numan Mahdi
    The steel industry is responsible for one-third of all global industrial CO2 emissions, putting pressure on the industry to shift forward towards more environmentally friendly production methods. The metallurgical industry is under enormous pressure to reduce CO2 emissions as a result of growing environmental concerns about global warming. The reduction in CO2 emissions is normally fulfilled by recycling steel waste into alkali-activated cement. Numerous types of steel waste have been produced via three main production routes, including blast furnace, electric arc furnace, and basic oxygen furnace. To date, all of the steel waste has been incorporated into alkali activation system to enhance the properties. This review focuses on the current developments over the last ten years in the steelmaking industry. This work also summarizes the utilization of steel waste for improving cement properties through an alkali activation system. Finally, this work presents some future research opportunities with regard to the potential of steel waste to be utilized as an alkali-activated material.
      23  3