Irfan Abd Rahim
Thumbnail Image
Preferred name
Irfan Abd Rahim
Official Name
Abd Rahim, Irfan
Alternative Name
Irfan, A. R.
Abd. Rahim., Irfan
Irfan, Abd Rahim
Abd Rahim, Irfan
Rahim, Irfan Abd
Main Affiliation
Scopus Author ID
56500369900
Researcher ID
GMC-2925-2022

Research Output

Filters

5
5
Reset filters

Settings
Now showing 1 - 5 of 5
  • Publication
    The mechanism analysis of belt-pulley driven spray plunger pump
    (AIP Publishing, 2023)
    Wan Abdul Rahman Assyahid Wan Ibrahim
    ;
    Irfan Abd Rahim
    ;
    Muhammad Rifqie
    ;
    Mohd Effendi Muhammad Suandi
    ;
    Muhammad Akmal Syakir
    ;
    Noorhafiza Muhammad
    ;
    Nur Amilea Nabila
    ;
    Nurul Izzati
    This paper presents an analysis of the mechanism of Belt-Pulley Driven Spray Plunger Pump. Belts and pulleys are used to transfer kinetic energy from the internal combustion (IC) engine to operate the pump. Combination of pulley and belts was used to transfer motion between each other simply without the need for meshed toothed gearing. The principal remains the same that there is a driver (powered) and driven (free). The benefit from application of belts which are mostly made of synthetic fibres is that no lubrication is necessary compared to chains. The analysis is focused on power transmitted from IC engine to plunger pump (design power) considering service factor as well as determining total number of belts to be used in the system with refer to FENNER Friction Belt Range Brochure Technical Docs.
  • Publication
    Design for assembly (DFA) analysis of old bicycle tire inflator
    ( 2020-11-02)
    Muhamad Farizuan Rosli
    ;
    Mohd Effendi Muhammad Suandi
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd. Nasir Mat Saad
    ;
    Irfan Abd Rahim
    This Paper is studied on the assembly problem of old bicycle tire inflator in the early stage of product design. During producing a product, the most important decisions are the final cost of the product. The approach based on Boothroyd Dewhurst methods has been implemented in this study to provide a quantitative measure called the design efficiency based on an analysis of a product. The main focuses of this research are to analyze the current design efficiency of old bicycle tire inflator and improved design efficiency. The product was design by using UNIGRAPHIC NX. The components and manufacturing of the old bicycle tire inflator were undergone alteration with the design for assembly (DFA) and redesigned methods.
      5  28
  • Publication
    Analysis of onion peeler machine using ansys simulation analysis
    ( 2020-11-02)
    Muhamad Farizuan Rosli
    ;
    Mohd Effendi Muhammad Suandi
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Mohd. Nasir Mat Saad
    ;
    Irfan Abd Rahim
    Onion is the important cooking ingredients in the world of a cook. The current method to peel an onion is by a traditional method. There are have many effects when using a traditional method such as used by a hand and knife. By using this traditional method, the probability of injured such as sore eyes and hand pain are too high. Beside that, the process also takes a long time if the user needs to peel in the large quantities. The development of onion peeling machine needs to achieve the objective such as increasing the safety, save time and energy of human. The method of use in this project in fabricating this machine is by analysing the source of information data and apply its knowledge in fabricating the onion peeling machine. The method of design is generated with followed the engineering design guided. The final design selection of machine transforms into a 3D drawing using CATIA software. And then, 3D CAD data are analyses using ANSYS CFX simulation software to analyses the flow analysis of the part design. From this result, it will be considered whether it is necessary to make improvements on the machine design to improve the capabilities and effectiveness.
      6  27
  • Publication
    Development of sustainable lightweight heat insulation panel from elastomeric and polymeric waste
    (AIP Publishing, 2023)
    Wan Abdul Rahman Assyahid Wan Ibrahim
    ;
    Irfan Abd Rahim
    ;
    Nurul Shakira Abd Rahma
    ;
    Mohd Effendi Muhammad Suandi
    ;
    Noorhafiza Muhammad
    The project present about development lightweight sustainable heat insulation panel from waste material. Scrap tyres and plastic waste was used for this purpose. The fabrication process started with scrap tyres is being cut and blends into smaller pieces. Then, the pieces of the material of rubber from scrap tyres are mixed together with the plastic waste material polyethylene at different composition. The mixture of the materials is pressed together using hydraulic press machine and heat are applied to melt the material in order to create the panel by using the mould. There are few tests that are conducted to the panel to find out its weight, volume and density. In order to determine the most suitable sample among the sample, a test is carried out to each sample. This test involved the black box or wooden box and the container by using the thermocouple and probes to measure the temperature. From the both test using black box and the container, the most suitable sample that excellent in insulating the heat is the sample with the bigger composition of rubber which are sample with 95% of rubber and 5% of polyethylene polymer.
      15  1
  • Publication
    Analysis a harvesting mechanism of swiftlets nest using finite element analysis
    ( 2020-11-02)
    Rosli M.F.
    ;
    Mohd Effendi Muhammad Suandi
    ;
    Mohd. Nasir Mat Saad
    ;
    Shayfull Zamree Abd. Rahim
    ;
    Irfan Abd Rahim
    For this project, it is focused on the harvesting swiftlets nest process to design and analysis new mechanism of harvest equipment. Industry swiftlets nest is not a new industry in Malaysia. It gets very high demand from China. Harvesting swiftlets nest is one of the processes to produce any products that made from swiftlets nest. Currently, they are using manual harvesting equipment to harvest swiftlets nest without using any auxiliary equipment. It is the first step in process flow and very important role before cleaning process. The objectives of this project are to design mechanism harvesting equipment to harvest swiftlets nest and to decrease the time of harvesting swiftlets nest process in a swiftlets house in a day. The design of harvesting equipment is using CAD software and then transfer to Finite Element Analysis (FEA) to analyses the capabilities of part design. At the end of this project, this research will give understanding about design using CAD software and do analysis that improved the harvesting equipment.
      4  32