Heah Cheng Yong
Thumbnail Image
Preferred name
Heah Cheng Yong
Official Name
Heah, Cheng Yong
Alternative Name
Yong, Heah Cheng
Yong, H. C.
Heah, Cheng Yong
Heah, C. Y.
Cheng-Yong, Heah
Cheng Yong, Heah
Main Affiliation
Scopus Author ID
54402789500
Researcher ID
S-7139-2019

Research Output
Now showing 1 - 2 of 2
  • Publication
    Formulation, mechanical properties and phase analysis of fly ash geopolymer with ladle furnace slag replacement
    ( 2021)
    Ng Hui-Teng
    ;
    Heah Cheng Yong
    ;
    Kong Ern Hun
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Liew Yun Ming
    ;
    Hasniyati Md Razi
    ;
    Ng Yong-Sing
    This paper presents the formulation of fly ash (FA) geopolymer and the incorporation of ladle furnace slag (LFS) as a replacement to FA in geopolymer formation. The formulation of the LFS replacement was set at 10–40 wt.%. The geopolymer was formed by mixing FA and LFS with a sodium-based alkali activator. The FA geopolymer had a compressive strength of 38.9 MPa with the optimum formulation of 8 M NaOH concentration, AS/AA ratio of 3, and AA ratio of 1.5. The compressive strength was affected more significantly by the amorphous content. The most influential factors affecting the properties of FA geopolymer were: AS/AA ratio > AA ratio > NaOH concentration. Replacing LFS led to very little (4.1%) increment in the compressive strength. The LFS had little contribution in supplying Si, Al and Ca for the formation of the N-A-S-H and C-A-S-H network. But LFS acted as a filler and improved the compactness of the FA geopolymer. The mechanical performance of FA/LFS geopolymer was not governed by the amorphous content like the FA geopolymer, as LFS addition contributed to increasing crystalline content. New crystalline phases of calcite and CSH due to the addition of LFS helped to retain the compressive strength of FA geopolymer. Nevertheless, the outcome of the study proved that LFS can be blended with FA to produce geopolymers without severe deterioration in mechanical strength. LFS can be potentially added in geopolymers as filler to produce geopolymer mortar.
  • Publication
    Evaluation of the effect of silica fume on amorphous fly ash geopolymers exposed to elevated temperature
    ( 2021)
    Ong Huey Li
    ;
    Liew Yun Ming
    ;
    Heah Cheng Yong
    ;
    Ridho Bayuaji
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Foo Kai Loong
    ;
    Tan Soo Jin
    ;
    Ng Hui Teng
    ;
    Marcin Nabiałek
    ;
    Bartlomiej Jeż
    ;
    Ng Yong Sing
    The properties of amorphous geopolymer with silica fume addition after heat treatment was rarely reported in the geopolymer field. Geopolymer was prepared by mixing fly ash and alkali activator. The silica fume was added in 2% and 4% by weight. The geopolymer samples were cured at room temperature for 28 days before exposed to an elevated temperature up to 1000 °C. The incorporation of 2% silica fume did not cause significant improvement in the compressive strength of unexposed geopolymer. Higher silica fume content of 4% reduced the compressive strength of the unexposed geopolymer. When subjected to elevated temperature, geopolymer with 2% silica fume retained higher compressive strength at 1000 °C. The addition of silica fume in fly ash geopolymer caused a lower degree of shrinkage and expansion, as compared to geopolymer without the addition of silica fume. Crystalline phases of albite and magnetite were formed in the geopolymer at 1000 °C.
      3  10