Noorina Hidayu Jamil
Thumbnail Image
Preferred name
Noorina Hidayu Jamil
Official Name
Noorina Hidayu, Jamil
Alternative Name
Jamil, Noorina Hidayu
Noorina, H. J.
Noorina, J. H.
Jamil, N. H.
Main Affiliation
Scopus Author ID
25639632500
Researcher ID
FBC-8988-2022

Research Output

Filters

1
6
Reset filters

Settings
Now showing 1 - 6 of 6
  • Publication
    Phase transformation of Kaolin-ground granulated blast furnace slag from geopolymerization to sintering process
    ( 2021-03-01)
    Noorina Hidayu Jamil
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Faizul Che Pa
    ;
    Hasmaliza M.
    ;
    Wan Mohd Arif W Ibrahim
    ;
    Aziz I.H.A.
    ;
    Jeż B.
    ;
    Nabiałek M.
    The main objective of this research was to investigate the influence of curing temperature on the phase transformation, mechanical properties, and microstructure of the as-cured and sintered kaolin-ground granulated blast furnace slag (GGBS) geopolymer. The curing temperature was varied, giving four different conditions; namely: Room temperature, 40, 60, and 80â—¦ C. The kaolin-GGBS geopolymer was prepared, with a mixture of NaOH (8 M) and sodium silicate. The samples were cured for 14 days and sintered afterwards using the same sintering profile for all of the samples. The sintered kaolin-GGBS geopolymer that underwent the curing process at the temperature of 60â—¦ C featured the highest strength value: 8.90 MPa, and a densified microstructure, compared with the other samples. The contribution of the Na2 O in the geopolymerization process was as a self-fluxing agent for the production of the geopolymer ceramic at low temperatures.
      2
  • Publication
    Effect of acid leaching on different state of rice husk
    (Trans Tech Publications Ltd., 2020)
    Nur Haslinda Mohamed Muzni
    ;
    Noorina Hidayu Jamil
    ;
    Faizul Che Pa
    ;
    Wan Mohd Arif W Ibrahim
    Rice husks (RH) are agricultural wastes available abundantly in rice producing country. A by-product obtained from combustion of rice husk is rice husk ash (RHA) which is rich in silica (SiO2) contents. This paper focused on the effect of acid leaching treatment on rice husk to produce high-purity silica. There are 4 different states of conditions involved; raw rice husk (RRH), treated rice husk (TRH), rice husk ash (RHA), and treated rice husk ash (TRHA). Citric acid; C6H8O7 was used as a leaching agent. TRH and TRHA was leached to see whether treated rice husk before combustion (TRH) or treated rice husk after combustion (TRHA) will produce more high-purity silica. Chemical composition analysis shows high amorphous silica content which is 98.47% with low metallic impurities at 1.0 M C6H8O7, 70 ºC for treated rice husk (TRH). X-ray diffraction (XRD) pattern shows the presence of amorphous silica in treated rice husk (TRH) and crystalline silica in treated rice husk ash (TRHA). Fragmentation of TRH into small pieces after acid leaching is seen where there is significant increase in the exposed surface areas. High-purity amorphous silica with more than 98% was prepared via citric acid leaching treatment and combustion process.
      1  19
  • Publication
    Alkaline-Activation technique to produce low-temperature sintering activated-HAp ceramic
    ( 2023)
    Wan Mohd Arif W Ibrahim
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Noorina Hidayu Jamil
    ;
    Hasmaliza Mohamad
    ;
    Mohd Arif Anuar Mohd Salleh
    ;
    Andrei Victor Sandu
    ;
    Petrica Vizureanu
    ;
    Madalina Simona Baltatu
    ;
    Patimapon Sukmak
    The fabrication of hydroxyapatite (HAp) ceramics prepared by existing conventional sintering requires high-temperature sintering of 1250 °C to 1300 °C. In this paper, the activated metakaolin (MK)/HAp specimens were prepared from varied mix design inputs, which were varied solid mixtures (different amounts of MK loading in HAp) and liquid-to-solid (L/S) ratios, before being pressed and sintered at 900 °C. Phase analysis, thermal analysis, surface morphology, and tensile strength of the specimens were investigated to study the influences of the Al, Si, Fe, Na, and K composition on the formation of the hydroxyapatite phase and its tensile strength. XRD analysis results show the formation of different phases was obtained from the different mix design inputs HAp (hexagonal and monoclinic), calcium phosphate, sodium calcium phosphate silicate and calcium hydrogen phosphate hydrate. Interestingly, the specimen with the addition of 30 g MK prepared at a 1.25 L/S ratio showed the formation of a monoclinic hydroxyapatite phase, resulting in the highest diametrical tensile strength of 12.52 MPa. Moreover, the increment in the MK amount in the specimens promotes better densification when sintered at 900 °C, which was highlighted in the microstructure study. This may be attributed to the Fe2O3, Na2O, and K2O contents in the MK and alkaline activator, which acted as a self-fluxing agent and contributed to the lower sintering temperature. Therefore, the research revealed that the addition of MK in the activated-HAp system could achieve a stable hydroxyapatite phase and better tensile strength at a low sintering temperature.
      2  25
  • Publication
    Phase transformation of Kaolin-Ground Granulated Blast Furnace Slag from geopolymerization to sintering process
    ( 2021)
    Noorina Hidayu Jamil
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Faizul Che Pa
    ;
    Mohamad Hasmaliza
    ;
    Wan Mohd Arif W Ibrahim
    ;
    Ikmal Hakem A. Aziz
    ;
    Bartłomiej Jeż
    ;
    Marcin Nabiałek
    The main objective of this research was to investigate the influence of curing temperature on the phase transformation, mechanical properties, and microstructure of the as-cured and sintered kaolin-ground granulated blast furnace slag (GGBS) geopolymer. The curing temperature was varied, giving four different conditions; namely: Room temperature, 40, 60, and 80 °C. The kaolin-GGBS geopolymer was prepared, with a mixture of NaOH (8 M) and sodium silicate. The samples were cured for 14 days and sintered afterwards using the same sintering profile for all of the samples. The sintered kaolin-GGBS geopolymer that underwent the curing process at the temperature of 60 °C featured the highest strength value: 8.90 MPa, and a densified microstructure, compared with the other samples. The contribution of the Na2O in the geopolymerization process was as a self-fluxing agent for the production of the geopolymer ceramic at low temperatures.
      19  2
  • Publication
    Self-Fluxing mechanism in geopolymerization for Low-Sintering temperature of ceramic
    ( 2021)
    Noorina Hidayu Jamil
    ;
    Mohd. Mustafa Al Bakri Abdullah
    ;
    Faizul Che Pa
    ;
    Hasmaliza Mohamad
    ;
    Wan Mohd Arif W Ibrahim
    ;
    Penphitcha Amonpattaratkit
    ;
    Joanna Gondro
    ;
    Wojciech Sochacki
    ;
    Norfadhilah Ibrahim
    Kaolin, theoretically known as having low reactivity during geopolymerization, was used as a source of aluminosilicate materials in this study. Due to this concern, it is challenging to directly produce kaolin geopolymers without pre-treatment. The addition of ground granulated blast furnace slag (GGBS) accelerated the geopolymerization process. Kaolin–GGBS geopolymer ceramic was prepared at a low sintering temperature due to the reaction of the chemical composition during the initial stage of geopolymerization. The objective of this work was to study the influence of the chemical composition towards sintering temperature of sintered kaolin–GGBS geopolymer. Kaolin–GGBS geopolymer was prepared with a ratio of solid to liquid 2:1 and cured at 60 °C for 14 days. The cured geopolymer was sintered at different temperatures: 800, 900, 1000, and 1100 °C. Sintering at 900 °C resulted in the highest compressive strength due to the formation of densified microstructure, while higher sintering temperature led to the formation of interconnected pores. The difference in the X-ray absorption near edge structure (XANES) spectra was related to the phases obtained from the X-ray diffraction analysis, such as akermanite and anothite. Thermal analysis indicated the stability of sintered kaolin–GGBS geopolymer when exposed to 1100 °C, proving that kaolin can be directly used without heat treatment in geopolymers. The geopolymerization process facilitates the stability of cured samples when directly sintered, as well as plays a significant role as a self-fluxing agent to reduce the sintering temperature when producing sintered kaolin–GGBS geopolymers.
      2  21