Mohd Arif Anuar Mohd Salleh
Thumbnail Image
Preferred name
Mohd Arif Anuar Mohd Salleh
Official Name
Mohd Arif Anuar, Mohd Salleh
Alternative Name
Mohd Salleh, Mohd Arif Anuar
Salleh, Mohd A.A.
Salleh, M. A.A.Mohd
Mohd Salleh, M. A.A.
Salleh, M. A.A.M.
Mohd Salleh, M. M.A.
Main Affiliation
Scopus Author ID
55543476900
Researcher ID
C-3386-2018

Research Output

Filters

5
5
5
Reset filters

Settings
Now showing 1 - 5 of 5
Thumbnail Image
Publication

Enhancement of Power Conversion Efficiency with Zinc Oxide as Photoanode and Cyanococcus, Punica granatum L., and Vitis vinifera as Natural Fruit Dyes for Dye-Sensitized Solar Cells

2022-11-01 , Ili Salwani Mohamad , Mohd Natashah Norizan , Norsuria Mahmed , Jamalullail N. , Dewi Suriyani Che Halin , Mohd Arif Anuar Mohd Salleh , Sandu A.V. , Baltatu M.S. , Vizureanu P.

Ruthenium N719 is a well-known material used as the dye in commercial dye-sensitized solar cell (DSSC) devices. However, it poses risks to human health and the environment over time. On the other hand, titanium dioxide (TiO2) has low electron mobility and high recombination losses when used as a photoanode in this photovoltaic technology device. In addition, using Ruthenium as the dye material harms the environment and human health. As an alternative sensitizer to compensate Ruthenium on two different photoanodes (TiO2 and ZnO), we constructed DSSC devices in this study using three different natural dyes (blueberry, pomegranate, and black grape). In good agreement with the anthocyanin content in the fruits, black grape, with the highest anthocyanin content (450.3 mg/L) compared to other fruit dyes (blueberry—386.6 mg/L and pomegranate—450.3 mg/L), resulted in the highest energy conversion efficiency (3.63%) for the natural dye-based DSSC. Furthermore, this research proved that the electrical performance of natural dye sensitizer in DSSC applications with a ZnO photoanode is better than using hazardous Ru N719 dye with a TiO2 photoanode owing to the advantage of high electron mobility in ZnO.

View
Thumbnail Image
Publication

Enhancement of Power Conversion Efficiency with Zinc Oxide as Photoanode and Cyanococcus, Punica granatum L., and Vitis vinifera as Natural Fruit Dyes for Dye-Sensitized Solar Cells

2022-11-01 , Ili Salwani Mohamad , Mohd Natashah Norizan , Norsuria Mahmed , Nurnaeimah Jamalullail , Dewi Suriyani Che Halin , Mohd Arif Anuar Mohd Salleh , Sandu A.V. , Baltatu M.S. , Vizureanu P.

Ruthenium N719 is a well-known material used as the dye in commercial dye-sensitized solar cell (DSSC) devices. However, it poses risks to human health and the environment over time. On the other hand, titanium dioxide (TiO2) has low electron mobility and high recombination losses when used as a photoanode in this photovoltaic technology device. In addition, using Ruthenium as the dye material harms the environment and human health. As an alternative sensitizer to compensate Ruthenium on two different photoanodes (TiO2 and ZnO), we constructed DSSC devices in this study using three different natural dyes (blueberry, pomegranate, and black grape). In good agreement with the anthocyanin content in the fruits, black grape, with the highest anthocyanin content (450.3 mg/L) compared to other fruit dyes (blueberry—386.6 mg/L and pomegranate—450.3 mg/L), resulted in the highest energy conversion efficiency (3.63%) for the natural dye-based DSSC. Furthermore, this research proved that the electrical performance of natural dye sensitizer in DSSC applications with a ZnO photoanode is better than using hazardous Ru N719 dye with a TiO2 photoanode owing to the advantage of high electron mobility in ZnO.

View
Thumbnail Image
Publication

Alkaline-Activation Technique to Produce Low-Temperature Sintering Activated-HAp Ceramic

2023-02-01 , Wan Mohd Arif W Ibrahim , Mohd. Mustafa Al Bakri Abdullah , Jamil N.H. , Mohamad H. , Mohd Arif Anuar Mohd Salleh , Sandu A.V. , Vizureanu P. , Baltatu M.S. , Sukmak P.

The fabrication of hydroxyapatite (HAp) ceramics prepared by existing conventional sintering requires high-temperature sintering of 1250 °C to 1300 °C. In this paper, the activated metakaolin (MK)/HAp specimens were prepared from varied mix design inputs, which were varied solid mixtures (different amounts of MK loading in HAp) and liquid-to-solid (L/S) ratios, before being pressed and sintered at 900 °C. Phase analysis, thermal analysis, surface morphology, and tensile strength of the specimens were investigated to study the influences of the Al, Si, Fe, Na, and K composition on the formation of the hydroxyapatite phase and its tensile strength. XRD analysis results show the formation of different phases was obtained from the different mix design inputs HAp (hexagonal and monoclinic), calcium phosphate, sodium calcium phosphate silicate and calcium hydrogen phosphate hydrate. Interestingly, the specimen with the addition of 30 g MK prepared at a 1.25 L/S ratio showed the formation of a monoclinic hydroxyapatite phase, resulting in the highest diametrical tensile strength of 12.52 MPa. Moreover, the increment in the MK amount in the specimens promotes better densification when sintered at 900 °C, which was highlighted in the microstructure study. This may be attributed to the Fe2O3, Na2O, and K2O contents in the MK and alkaline activator, which acted as a self-fluxing agent and contributed to the lower sintering temperature. Therefore, the research revealed that the addition of MK in the activated-HAp system could achieve a stable hydroxyapatite phase and better tensile strength at a low sintering temperature.

View
Thumbnail Image
Publication

Mechanical Performance, Microstructure, and Porosity Evolution of Fly Ash Geopolymer after Ten Years of Curing Age

2023-02-01 , Aziz I.H.A. , Mohd. Mustafa Al Bakri Abdullah , Rafiza Abd Razak , Zarina Yahya , Mohd Arif Anuar Mohd Salleh , Chaiprapa J. , Rojviriya C. , Vizureanu P. , Sandu A.V. , Muhammad Faheem Mohd. Tahir , Alida Abdullah , Liyana Jamaludin

This paper elucidates the mechanical performance, microstructure, and porosity evolution of fly ash geopolymer after 10 years of curing age. Given their wide range of applications, understanding the microstructure of geopolymers is critical for their long-term use. The outcome of fly ash geopolymer on mechanical performance and microstructural characteristics was compared between 28 days of curing (FA28D) and after 10 years of curing age (FA10Y) at similar mixing designs. The results of this work reveal that the FA10Y has a beneficial effect on strength development and denser microstructure compared to FA28D. The total porosity of FA10Y was also lower than FA28D due to the anorthite formation resulting in the compacted matrix. After 10 years of curing age, the 3D pore distribution showed a considerable decrease in the range of 5–30 µm with the formation of isolated and intergranular holes.

View
Thumbnail Image
Publication

Controlling the Layer Thickness of Zinc Oxide Photoanode and the Dye-Soaking Time for an Optimal-Efficiency Dye-Sensitized Solar Cell

2023-01-01 , Magiswaran K. , Mohd Natashah Norizan , Norsuria Mahmed , Ili Salwani Mohamad , Idris S.N. , Sabri M.F.M. , Amin N. , Sandu A.V. , Vizureanu P. , Nabiałek M. , Mohd Arif Anuar Mohd Salleh

Dye-sensitized solar cells (DSSCs) were developed by exploiting the photovoltaic effect to convert solar energy into electrical energy. The photoanode layer thickness significantly affects the semiconductor film’s ability to carry electronic charges, adsorb sensitizing dye molecules, and lower the recombination of photo-excited electrons injected into the semiconductor. This study investigated the dependence of the zinc oxide (ZnO) photoanode thin-film thickness and the film soaking time in N719 dye on the photocurrent–voltage characteristics. The ZnO photoanode was applied to glass using the doctor blade method. The thickness was varied by changing the scotch tape layers. The ZnO-based DSSC attained an efficiency of 2.77% with three-layered photoanodes soaked in the dye for three hours, compared to a maximum efficiency of 0.68% that was achieved with three cycles using the dip-coating method in other research. The layer thickness of the ZnO photoanode and its optimal adsorption time for the dye are important parameters that determine the efficiency of the DSSC. Therefore, this work provides important insights to further improve the performance of DSSCs.

View