Junaidah Ali Mohd Jobran
Thumbnail Image
Preferred name
Junaidah Ali Mohd Jobran
Official Name
Ali Mohd Jobran, Junaidah
Alternative Name
Junaidah Ali Mohd Jobran,
Jobran, Junaidah Ali Mohd
Main Affiliation
Scopus Author ID
55612070700
Researcher ID
CVW-3675-2022

Research Output

Filters

3
2 1
3
3
Reset filters

Settings
Now showing 1 - 3 of 3
Thumbnail Image
Publication

Piezoelectric Array Configuration Technique into Enhance Power Catchment for Sound Energy Harvester System

2020-11-18 , Liew Hui Fang , Rosemizi Abd Rahim , Muhammad Izuan Fahmi Romli , Mohamad Zhafran Zakariya , Junaidah Ali Mohd Jobran , Norhanisa Kimpol

The objective of this study is to explore the harvest maximum output changes occurs in piezoelectric transducer when connected in different configuration to produce highest electricity consumption and generate sound energy harvesting system. Acoustic energy is a type of environmental energy source that can be extracted and converted into electrical energy for small-scale energy applications. In this study, the corresponding load resistance for single piezoelectric transducer is 4.5 k$\Omega$, together with a constant vibration source at a frequency of 68 Hz and a 1-g acceleration. The performance of output voltage and power of piezoelectric are evaluated and the optimum output is measured by depending on the connection of the piezoelectric transducer arrangement into series, parallel and series, and parallel which stimulated using Proteus software. The experiment result presented that, when have single piezo, 5 piezo connected in series, and 5 piezo connected in parallel, the output powers are 1.664 mW, 1.671mW and 7.676 mW, respectively. During the combination series and parallel connections, the output power of 3S1P piezo increases to 5.05mW. In a parallel configuration, the output voltage that produced is much higher than a piezoelectric transducer arrangement connected in series connection. The piezoelectric transducer that connected in parallel configurations increases its voltage output from 2.83 V to 13.05 V with the same polarity. The arrangement of piezoelectric transducer in parallel configuration is affordable, with its higher production of a higher power output compared to the arrangement of piezoelectric transducer in series connection. Whereas in terms of power output, the maximum power remains constant in the range of 1.665 to 1.671 mW when three transducers are in series configuration connection with the same polarity. In conclusion, the proper implementation of the piezoelectric array configuration is needed in order to operate the minimum energy for low load devices and promise to accomplish generated optimum power output in harvester system.

View
Thumbnail Image
Publication

Solar Powered Multiple Output Buck Converter

2020-12-18 , Muhammad Zaid Aihsan , Norhanisa Kimpol , Liew Hui Fang , Muhammad Izuan Fahmi Romli , Wan Azani Wan Mustafa , Junaidah Ali Mohd Jobran , Mohamed Mydin Hj M.Abdul Kader

Times have certainly changed over the past few decades, now it seems that technology is getting more compact and efficient. The modern outdoor enthusiast such as hikers, climbers has a problem regarding the lack of power supply to power up electronics when they go for adventure activities. In order to solve this problem, this paper design and develop DC/DC buck converter system to drop down the voltage from the solar photovoltaic (PV) system from 12VDC into 5VDC. This paper is first to start up with design and simulation circuit using simulation to test outcome of this paper in the range of 5VDC & 1.0A and 5VDC & 0.5A. A battery storage is needed to feed electricity independent and battery management of the battery is needed to improve the performance of battery life. This can be done by adding a charge controller unit. The outcome of this paper allows the battery to be charged using the solar panel and at the same time can produce multiple outputs for low voltages used. The software simulation has been done to shows this system produces two different output and the hardware will be developed based on the software results. Software and hardware result, both will be compared and analysed.

View
Thumbnail Image
Publication

Adaptive PD Controller Performance for Direct Cooling of Thermoelectric Refrigerator

2020-12-18 , Mohd Saifizi Saidon , Mohd Rizal Manan , Baseemah Mat Jalaluddin , Junaidah Ali Mohd Jobran , Wan Azani Wan Mustafa , Roejhan Md Kawi , Lee T.W. , Mat Piah M.S. , Diana N.S.

Refrigerator is the key component to keep the medicine and biological sample in the hospital. The domestic refrigerator has the problem of larger size and heavier weight since to the compact system like condenser, compressor, evaporator and expansion valve are assemble and using in the refrigerator. This project focused on design of temperature control of the portable thermoelectric refrigerator for medical purpose. Thermoelectric refrigerator is using the direct cooling method through thermoelectric module. Thermoelectric refrigerator has several advantages such as smaller size, lighter and silent when operated. Since maintain a constant temperature for the storage of medical product is important, a specific refrigerator is needed to ensure the medicine is stored in desired temperature. This project is to design and develop an adaptive control system which can perform a good temperature control for the thermoelectric refrigerator. The second order model is applied to design adaptive Proportional-Derivative (PD) controller. The selected controller is the adaptive PD controller because the performance of response shows 0.42 C of less steady state error and 0.21 C of lower undershoot. The adaptive PD control system designed able to let the refrigerator operate in different operating condition without influence the performance of the refrigerator.

View