Roshaliza Hamidon
Thumbnail Image
Preferred name
Roshaliza Hamidon
Official Name
Roshaliza, Hamidon
Alternative Name
Hamidon, Roshaliza
Hamidon, R.
Main Affiliation
Scopus Author ID
54941292900
Researcher ID
ICQ-9949-2023

Research Output

Filters

5
2
5
5
Reset filters

Settings
Now showing 1 - 5 of 5
  • Publication
    Implementation of PID Controller for Solar Tracking System
    ( 2021-01-01)
    Zakaria S.
    ;
    Ong J.Q.
    ;
    Engku Ariff E.A.R.
    ;
    Roshaliza Hamidon
    ;
    Zailani Zainal Abidin
    ;
    Muhammad Syahril Bahari
    ;
    Azmi Harun
    Proportional integral derivative (PID) controllers are widely used in industrial processes cue to their simplicity and effectiveness for linear and nonlinear systems. Solar tracking system is one of the most direct approaches adopted to harvest more solar energy from photovoltaic (PV) system compared to stationary solar system. Hence, the PV panels able to receive maximum sunlight and generate more energy. Arduino based prototype dual axis (Azimuth-Altitude) solar tracking system is constructed with the implementation of PID controller. The performance of dual axis tracking system and stationary solar system are compared and discussed. Types of tuning methods for PID constant will be determine with use of Arduino IDE. Comparative results depicted that performance in terms of current, voltage and power value. According to results, dual axis solar tracking system with implement of PID controller is shown better performance compare to stationary solar system.
  • Publication
    Improvement on the Surface Quality in Machining of Aluminum Alloy Involving Boron Nitride Nanoparticles
    ( 2021-01-01)
    Zailani Zainal Abidin
    ;
    Zaibi N.M.
    ;
    Roshaliza Hamidon
    ;
    Harun A.
    ;
    Muhammad Syahril Bahari
    ;
    Zakaria S.
    Aluminum Alloys are used in a variety of applications due to their lightweight, strength-to-weight ratio and relatively ease of fabrication. In aerospace industry, millions of holes drilled annually on airframe structures. Normally, cutting fluids have been used to help reduce friction and heat. However, the use of cutting fluid is one of the major concerns when considering the environmental issues in machining. The disposal of used cutting fluid poses problems to the environment. This research investigates the effect of greener technique; hexagonal Boron Nitride nanoparticles dispersed in oil as compared to dry cutting and oil alone in through hole drilling operation Their impact on tool wear, surface roughness, and holes quality in terms of diameter accuracy, circularity and cylindricity were experimentally studied. Results showed that application of hexagonal Boron Nitride improved surface finish and produced better dimensional hole accuracy. The work clearly shows the important of nanoparticles in improving machinability of this material.
  • Publication
    Study the Effect of Cutting Parameter in Machining Kenaf Fiber Reinforced Plastic Composite Materials Using DOE
    ( 2021-01-01)
    Azmi Harun
    ;
    Che Haron C.H.
    ;
    Zailani Zainal Abidin
    ;
    Roshaliza Hamidon
    ;
    Muhammad Syahril Bahari
    ;
    Zakaria S.
    ;
    Hamid S.H.A.
    Natural fiber is a hairy like raw material which comes from natural sources such as animal, plant, and mineral fibers. Kenaf fiber known with scientific name as Hibiscus Cannabinus is one natural fibers which becoming popular as a reinforced for plastic composites material in the industrial application such as automobile, aircraft, and marine engineering. However, milling these materials present a few problems, which are surface roughness and delamination factors are appear during the machining process, associated with the characteristics of the material and the cutting parameter. The objective of evaluating the cutting parameters (spindle speed, feed rate, and depth of cut), the influence of the fibers under surface roughness (Ra) and delamination factor (Fd). In this research study, Response Surface Methodology (RSM) was used to conduct the experiment. In addition, this method established considering milling with prefixed cutting parameters using HSS end mill. The experiment result was analyzed using Design Expert software. It was found that the optimum parameters for the minimum surface roughness and delamination were spindle speed at 2000 rpm, feed rate at 300 mm/min, and depth of cut at 2.0 mm. The spindle speed and feed rate are the main factors influence the effect of surface roughness and delamination in kenaf fiber reinforced plastic. High spindle speed and low feed rate resulted in minimum surface roughness and delamination.
  • Publication
    Effect of Different Cutting Conditions on Tool Wear and Chip Formation in Drilling of Cobalt Chromium Molybdenum
    ( 2021-01-01)
    Roshaliza Hamidon
    ;
    Zulkefli N.A.
    ;
    Saravanan R.
    ;
    Zailani Zainal Abidin
    ;
    Muhammad Syahril Bahari
    ;
    Zakaria S.
    ;
    Azmi Harun
    Cobalt-Chromium Molybdenum (CoCrMo) alloy is categorized under hard to cut material due to its unique combination characteristics such as high strength and low thermal conductivity. However, there was a problem during machining hard alloy material which is rapid tool wear. The tool wear will cause changes at tooltip geometry consequently has significant influence on the chip forming. There are some factors that influence tool wear which are cutting parameters, type of drill bit, and cutting fluids. In this study, a series of experiment were conducted to investigate the effect of cooling conditions on tool wear and chip formation during drilling this material. The cooling conditions used were dry, pure Karanja oil (MQL condition), and combination of Hexagonal boron nitride (hBN) nanoparticles with Karanja oil (MQL condition). The experiment was conducted under constant cutting speed of 20 m/min, and feed rate of 0.07 mm/rev through holes. Each hole was inspected when the tool wear reached 0.3 mm. The result showed that mixed of hBN with Karanja Oil (MQL condition) had lowest growth of flank wear and produced more holes compared to dry and pure Karanja oil condition. In addition, for chip formation, the size of lamellae produced was finest compared to other conditions.
  • Publication
    Nature Driven IOT Based Automation of Aquaponic System
    ( 2021-01-01)
    Zakaria S.
    ;
    Jafri M.A.A.A.
    ;
    Ariff E.A.R.
    ;
    Roshaliza Hamidon
    ;
    Zailani Zainal Abidin
    ;
    Muhammad Syahril Bahari
    ;
    Azmi Harun
    Automation of Aquaponic with (Internet of Things) IoT system model is designed with the integration of hydroponics (growing plant or vegetable without soil), aquaculture (fish farming) and vertical farming. The main purpose of the designed model is to ultimately support the survival and healthy growth of bacteria in plants, fish as well as saving water by increasing the productivity. The development of the system with IoT to monitor and control parameters such as water level, water temperature and water pH. The control system based on Arduino Uno, multiple sensors for water pH, water level and water temperature as well as automatic feeder dispenser are used in this project. This system is using IoT as a platform supported by Wi-Fi module ESP8266 Wi-Fi module in Blynk Software. System settings and controls can be carried out manually on the main control unit or remotely through mobile phone commands. This system also used to collect different data parameters and those data will be compared with the optimal range as the data will be transferred to Blynk for analysis. Therefore, the design system can operate independently without manually monitoring and utilized IoT to control and monitor the system systematically.