Ahmad Fairuz Mansor
Thumbnail Image
Preferred name
Ahmad Fairuz Mansor
Official Name
Ahmad Fairuz, Mansor
Alternative Name
Mansor, A. F.
Fairuz, M. A.
Mansor, Ahmad Fairuz
Main Affiliation
Scopus Author ID
56674123300
Researcher ID
DUZ-9034-2022

Research Output

Filters

8
6
8
Reset filters

Settings
Now showing 1 - 8 of 8
  • Publication
    Electrical discharge coating of NiTi alloy in deionized water
    ( 2021-01-01)
    Jamaluddin R.
    ;
    Tan Chye Lih
    ;
    Roshaliza Hamidon
    ;
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    Shape memory alloys, specifically nickel-titanium (NiTi), exhibit excellent technical properties that suited them for biomedical applications. However, the release of nickel ions into human body is a drawback because it results in severe adverse health effects as well as degrades the biocompatibility of the alloys. In this work, surface modification through adaptation of electrical discharge machining was used to develop a deposition layer of titanium oxide on NiTi alloy surface. The adaptation was through electrical discharge coatings (EDC) parameters such as polarity, gap voltage, and erosion depth that were set up to study their effects on the experimental performance. The experiment was parameterized by implementing 2 level of full factorial design with ANOVA analysis to measure the surface roughness of that machined surface. One-factor-at-a-time, OFAT method is applied for XRD analysis by adopting the previous parameters approach. The EDC process was aided with deionized water and pure titanium rod as the dielectric fluids and electrodes, respectively. It was determined that the high level of gap voltage provided some major constituents on the surface of NiTi alloy based on XRD analysis. As apparent, this substantiated the presence of the tool materials and their oxide layer phases. The interaction of polarity and gap voltage also indicated a significant effect towards the surface roughness.
  • Publication
    Surface roughness analysis of NiTi alloy in electrical discharge coating process
    ( 2020-12-18)
    Jamaluddin R.
    ;
    Lih T.C.
    ;
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    ;
    Roshaliza Hamidon
    Nickel-Titanium (NiTi) alloys, most widely known as nitinol, are presently employed in many micro-engineering applications such as coronary stents of medical implants due to their unique properties (shape memory effect and superelasticity). However, non-optimized surface finishing attributed a significantly high potential of nickel exposure after a long time of application. Releasing of nickel ion to the body environment can be harmful and toxicity resulting in adverse health as well as degrading the material biocompatibility. It is widely known that controlled surface roughness play a vital role in the formation of new bone ingrowths around implant. In this study, surface modification of NiTi alloy was used through electrical discharge coating (EDC); an adaptation of electrical discharge machining. The potential of EDC in which can facilitates the production of hard coatings may exploit the phenomena for the attachment of desirable materials onto the surface of materials. Therefore, the aim of this paper is to present a robust method (two levels of full factorial design and ANOVA) to determine the desired parameters and significant factors based on the surface roughness of the machined surface. Manipulation of parameters set up such as gap voltage, discharge duration and pulse interval and the current were employed and a reverse polarity was selected for this experiment. The results demonstrated that the most significant factors influence the surface coating performances are the discharge duration, current, gap voltage as well as the interaction between gap voltage and discharge duration.
  • Publication
    The Effect of Parameters of Electrical Discharge Coatings on the Tool Electrode Erosion and Maximum Height Roughness on NiTi Alloy
    ( 2021-01-01)
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    ;
    Zain M.Z.M.
    ;
    Jamaluddin R.
    This paper presents the influence of electrical discharge coatings parameters on the material loss due to the tool electrode erosion (MLTE) and the maximum height roughness, Rz on the NiTi alloy substrate. Five parameters were investigated; namely polarity, discharge duration, peak current, pulse interval and gap voltage. The experimental study was carried out using 2-level factorial design and analyzed using analysis of variance (ANOVA). The analysis results showed that the discharge duration dominates the effect on MLTE and Rz up to 39.39 and 72.41%, respectively. Then, this followed by the peak current at 15.52 and 4.63%, respectively. Furthermore, several interactions between discharge duration with other parameters were also significant on the model for both responses. Higher MLTE and Rz were recorded during high discharge duration and peak current due to the impact of increasing the discharge energy.
  • Publication
    Performance study of biocompatible recast layer formation on Ti6Al4V by using electrical discharge coatings
    ( 2020-04-01)
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    ;
    Zahiruddin M.
    ;
    Islam M.N.
    Long-term implantation of titanium-based alloy, Ti6Al4V can be harmful in human bodies due to the release of aluminium and vanadium elements. Thus, a biocompatible barrier coating can be applied towards corrosion and wear resistance of the implant. In this research, the surface of a biomedical grade of Ti6Al4V was coated with a thin film of biomaterial ceramic by the electrical discharge coatings (EDC) using a pure graphite electrode. Polarity, discharge duration and pulse interval were varied to investigate the formation of recast layer thickness (RLT) on the surface of titanium alloys. RLT was measured from cross-sectioned samples using a high magnification optical microscopy. From the statistical analyses of variance, the response was significantly influenced by the pulse interval, followed with electrode polarity. Additionally, the interaction of polarity to discharge duration and pulse interval also significantly affect the RLT. In order to obtain a more uniform recast layer formation, the process condition should be in reverse polarity with a low setting of pulse interval.
  • Publication
    Effects of machining conditions on the specific cutting energy of carbon fibre reinforced polymer composites
    ( 2017-10-29)
    Azwan Iskandar Azmi
    ;
    Syahmi A.
    ;
    Naquib M.
    ;
    Tan Chye Lih
    ;
    Ahmad Fairuz Mansor
    ;
    Khalil A.
    This article presents an approach to evaluate the effects of different machining conditions on the specific cutting energy of carbon fibre reinforced polymer composites (CFRP). Although research works in the machinability of CFRP composites have been very substantial, the present literature rarely discussed the topic of energy consumption and the specific cutting energy. A series of turning experiments were carried out on two different CFRP composites in order to determine the power and specific energy constants and eventually evaluate their effects due to the changes in machining conditions. A good agreement between the power and material removal rate using a simple linear relationship. Further analyses revealed that a power law function is best to describe the effect of feed rate on the changes in the specific cutting energy. At lower feed rate, the specific cutting energy increases exponentially due to the nature of finishing operation, whereas at higher feed rate, the changes in specific cutting energy is minimal due to the nature of roughing operation.
  • Publication
    Evaluation of thickness variation of recast layer formation on nitinol from electrical discharge coatings process
    ( 2020-06-17)
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    ;
    Zain M.Z.M.
    ;
    Jamaluddin R.
    Nitinol is an intermetallic alloy with outstanding properties that suitable as biomaterial. This alloy is capable of recovering to its initial shape after external loading through transformation of the crystalline structure. Unfortunately, excessive exposure of nickel element from this alloy is harmful to human body if released. Thus in this study, the alloy surface was deposited with an oxide layer via electrical discharge coating (EDC) process. The process was performed in deionized water and pure titanium as the electrode. The variation thickness of the recast layer formation was examined by analysing the effects of polarity, gap voltage and erosion depth. Single crater images and electrical waveforms were captured and utilised to elucidate the aforementioned effects. The results exhibited a significant change of layer thickness variation due to different polarity conditions. It was also confirmed that the single crater formation at different polarity was influenced by discharge energy. On other hand, the increase in the open gap voltage can expand the recast layer thickness in lower variation of reverse polarity condition. Finally, erosion depth attributed to a constant layer thickness but in low thickness variation when reverse polarity was employed.
  • Publication
    A study of energy consumption in turning process using lubrication of nanoparticles enhanced coconut oil (NECO)
    ( 2017-10-29)
    Ahmad Fairuz Mansor
    ;
    Muhammad Syamil Zakaria
    ;
    Azwan Iskandar Azmi
    ;
    Ahmad Nabil Mohd Khalil
    ;
    Musa N.A.
    Cutting fluids play very important role in machining application in order to increase tool life, surface finish and reduce energy consumption. Instead of using petrochemical and synthetic based cutting fluids, vegetable oil based lubricants is safety for operators, environmental friendly and become more popular in the industrial applications. This research paper aims to find the advantage of using vegetable oils (coconut oil) with additional of nano particles (CuO) as lubricant to the energy consumption during machining process. The energy was measured for each run from 2 level factorial experimental layout. Obtained results illustrate that lubricant with enhancement of nanoparticles has capability to improve the energy consumption during the machining process.
  • Publication
    Experimental investigation on the microdefects formation due to the electrical discharge coating process: A fractional factorial design
    ( 2024-03-07)
    Ahmad Fairuz Mansor
    ;
    Azwan Iskandar Azmi
    ;
    Zailani Zainal Abidin
    ;
    Zain M.Z.M.
    Electrical discharge coating (EDC) is a well-known technique among researchers for modification of metallic surfaces. This process is capable of producing a hard coating layer, biocompatible and high corrosion resistance at low operating cost. Unfortunately, the process develops unfavourable microcracks and porosity on the substrate surface attributed by heat generation. Thus, in this study, the effect of several parameters to the microdefects' formation was investigated through an experimental work based on fractional factorial design. This work was conducted on a nickel-titanium (NiTi) shape memory alloy by varying the EDC parameters, namely; polarity, discharge duration, peak current, pulse interval, gap voltage and additive Ti nano powder concentration in deionized water (DI water). ANOVA results exhibited that the discharge duration has dominated the microcracks and porosity fraction on the substrate surface due to the impact of high intensity of discharge energy. Although, the Ti nano powder mixed in the DI water had capability to reduce the microcracks formation, the porosity fraction during at high gap voltage setting was elevated with the Ti nano powder mixed.