Umi Fazara Md Ali
Thumbnail Image
Preferred name
Umi Fazara Md Ali
Official Name
Umi Fazara, Md Ali
Alternative Name
Ali, Umi Fazara Md
Md. Ali, Umi Fazara
Umi Fazara, M. A.
Main Affiliation
Scopus Author ID
57195513638
Researcher ID
AAU-4840-2020

Research Output

Filters

5
5
5
Reset filters

Settings
Now showing 1 - 5 of 5
Thumbnail Image
Publication

Sulfur dioxide removal by calcium-modified fibrous KCC-1 mesoporous silica: kinetics, thermodynamics, isotherm and mass transfer mechanism

2022-04-01 , Hanif M.A. , Naimah Ibrahim , Khairuddin Md Isa , Umi Fazara Md Ali , Tuan Abdullah T.A. , Jalil A.A.

The removal of sulfur dioxide from industrial flue gas through dry flue gas desulfurization method commonly involves the use of adsorption process with porous sorbent. The efficiency of this process is highly dependent on the adsorption capacity and the adsorption rate of SO2 onto the sorbent materials. The use of KCC-1 mesoporous silica modified with calcium metal additives (Ca/KCC-1) in SO2 adsorption is examined in a fixed bed reactor system. The adsorption capacity of Ca/KCC-1 is found to be critically governed by the reaction temperature and inlet SO2 concentration where low values of both parameters are favorable to achieve the highest adsorption capacity of 3241.94 mg SO2/g sorbent. SO2 molecules are adsorbed on the surface of Ca/KCC-1 by both physisorption and chemisorption processes as assumed by the Avrami kinetic model. Thermodynamic study shows that the process is exothermic and spontaneous in nature, and changes from an ordered stage on the surface of KCC-1 towards an increasingly random stage. The process is well explained by Freundlich isotherm model indicating a slightly heterogeneous process and moderate adsorption capacity. The adsorption stage is limited by film diffusion at the initial stage and by intraparticle diffusion during the transfer of SO2 into the network of pores before adsorption takes place on the active sites.

View
Thumbnail Image
Publication

Microplastics and nanoplastics: Recent literature studies and patents on their removal from aqueous environment

2022-03-01 , Muhammad Adli Hanif , Naimah Ibrahim , Farrah Aini Dahalan , Umi Fazara Md Ali , Masitah Hasan , Jalil A.A.

The presence of microplastics (MP) and nanoplastics (NP) in the environment poses significant hazards towards microorganisms, humans, animals and plants. This paper is focused on recent literature studies and patents discussing the removal process of these plastic pollutants. Microplastics and nanoplastics can be quantified by counting, weighing, absorbance and turbidity and can be further analyzed using scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, surface-enhanced Raman spectroscopy and Raman tweezers. Mitigation methods reported are categorized depending on the removal characteristics: (i) Filtration and separation method: Filtration and separation, electrospun nanofiber membrane, constructed wetlands; (ii) Capture and surface attachment method: coagulation, flocculation and sedimentation (CFS), electrocoagulation, adsorption, magnetization, micromachines, superhydrophobic materials and microorganism aggregation; and (iii) Degradation method: photocatalytic degradation, microorganism degradation and thermal degradation; where removal efficiency between 58 and 100% were reported. As these methods are significantly distinctive, the parameters which affect the MP/NP removal performance e.g., pH, type of plastics, presence of interfering chemicals or ions, surface charges etc. are also discussed. 42 granted international patents related to microplastics and nanoplastics removal are also reviewed where the majority of these patents are focused on separation or filtration devices. These devices are efficient for microplastics up to 20 μm but may be ineffective for nanoplastics or fibrous plastics. Several patents were found to focus on methods similar to literature studies e.g., magnetization, CFS, biofilm and microorganism aggregation; with the addition of another method: thermal degradation.

View
Thumbnail Image
Publication

Microplastics in facial cleanser: extraction, identification, potential toxicity, and continuous-flow removal using agricultural waste–based biochar

2023-05-01 , Hanif M.A. , Naimah Ibrahim , Farrah Aini Dahalan , Umi Fazara Md Ali , Masitah Hasan , Ayu Wazira Azhari , Jalil A.A.

Microplastic (MP) is an emerging contaminant of concern due to its ubiquitous quantity in the environment, small size, and potential toxicity due to strong affinity towards other contaminants. In this work, MP particles (5–300 μm) were extracted from a commercial facial cleanser and determined to be irregular polyethylene (PE) microbeads based on characterization with field emission scanning electron microscopy (FESEM) and Raman spectroscopy. The potential of extracted MP acting as toxic pollutants’ vector was analyzed via adsorption of methylene blue and methyl orange dye where significant dye uptake was observed. Synthetic wastewater containing the extracted MP was subjected to a continuous-flow column study using palm kernel shell and coconut shell biochar as the filter/adsorbent media. The prepared biochar was characterized via proximate and ultimate analysis, FESEM, contact angle measurement, atomic force microscopy (AFM), and Fourier transform infrared (FTIR) spectroscopy to investigate the role of the biochar properties in MP removal. MP removal performance was determined by measuring the turbidity and weighing the dry mass of particles remaining in the effluent following treatment. Promising results were obtained from the study with highest removal of MP (96.65%) attained through palm kernel shell biochar with particle size of 0.6–1.18 mm and continuous-flow column size of 20 mm. Graphical abstract: [Figure not available: see fulltext.].

View
Thumbnail Image
Publication

Sulfur dioxide removal by calcium-modified fibrous KCC-1 mesoporous silica: kinetics, thermodynamics, isotherm and mass transfer mechanism

2022-04-01 , Muhammad Adli Hanif , Naimah Ibrahim , Khairuddin Md Isa , Umi Fazara Md Ali , Tuan Abdullah T.A. , Jalil A.A.

The removal of sulfur dioxide from industrial flue gas through dry flue gas desulfurization method commonly involves the use of adsorption process with porous sorbent. The efficiency of this process is highly dependent on the adsorption capacity and the adsorption rate of SO2 onto the sorbent materials. The use of KCC-1 mesoporous silica modified with calcium metal additives (Ca/KCC-1) in SO2 adsorption is examined in a fixed bed reactor system. The adsorption capacity of Ca/KCC-1 is found to be critically governed by the reaction temperature and inlet SO2 concentration where low values of both parameters are favorable to achieve the highest adsorption capacity of 3241.94 mg SO2/g sorbent. SO2 molecules are adsorbed on the surface of Ca/KCC-1 by both physisorption and chemisorption processes as assumed by the Avrami kinetic model. Thermodynamic study shows that the process is exothermic and spontaneous in nature, and changes from an ordered stage on the surface of KCC-1 towards an increasingly random stage. The process is well explained by Freundlich isotherm model indicating a slightly heterogeneous process and moderate adsorption capacity. The adsorption stage is limited by film diffusion at the initial stage and by intraparticle diffusion during the transfer of SO2 into the network of pores before adsorption takes place on the active sites.

View
Thumbnail Image
Publication

Microplastics and nanoplastics: Recent literature studies and patents on their removal from aqueous environment

2022-03-01 , Hanif M.A. , Naimah Ibrahim , Farrah Aini Dahalan , Umi Fazara Md Ali , Masitah Hasan , Jalil A.A.

The presence of microplastics (MP) and nanoplastics (NP) in the environment poses significant hazards towards microorganisms, humans, animals and plants. This paper is focused on recent literature studies and patents discussing the removal process of these plastic pollutants. Microplastics and nanoplastics can be quantified by counting, weighing, absorbance and turbidity and can be further analyzed using scanning electron microscopy (SEM), dynamic light scattering (DLS), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, surface-enhanced Raman spectroscopy and Raman tweezers. Mitigation methods reported are categorized depending on the removal characteristics: (i) Filtration and separation method: Filtration and separation, electrospun nanofiber membrane, constructed wetlands; (ii) Capture and surface attachment method: coagulation, flocculation and sedimentation (CFS), electrocoagulation, adsorption, magnetization, micromachines, superhydrophobic materials and microorganism aggregation; and (iii) Degradation method: photocatalytic degradation, microorganism degradation and thermal degradation; where removal efficiency between 58 and 100% were reported. As these methods are significantly distinctive, the parameters which affect the MP/NP removal performance e.g., pH, type of plastics, presence of interfering chemicals or ions, surface charges etc. are also discussed. 42 granted international patents related to microplastics and nanoplastics removal are also reviewed where the majority of these patents are focused on separation or filtration devices. These devices are efficient for microplastics up to 20 μm but may be ineffective for nanoplastics or fibrous plastics. Several patents were found to focus on methods similar to literature studies e.g., magnetization, CFS, biofilm and microorganism aggregation; with the addition of another method: thermal degradation.

View