Mohd Arif Anuar Mohd Salleh
Thumbnail Image
Preferred name
Mohd Arif Anuar Mohd Salleh
Official Name
Mohd Arif Anuar, Mohd Salleh
Alternative Name
Mohd Salleh, Mohd Arif Anuar
Salleh, Mohd A.A.
Salleh, M. A.A.Mohd
Mohd Salleh, M. A.A.
Salleh, M. A.A.M.
Mohd Salleh, M. M.A.
Main Affiliation
Scopus Author ID
55543476900
Researcher ID
C-3386-2018

Research Output
Now showing 1 - 10 of 10
Thumbnail Image
Publication

Mechanical performance, microstructure, and porosity evolution of fly ash geopolymer after ten years of curing age

2023 , Ikmal Hakem A. Aziz , Mohd. Mustafa Al Bakri Abdullah , Rafiza Abd Razak , Zarina Yahya , Mohd Arif Anuar Mohd Salleh , Jitrin Chaiprapa , Catleya Rojviriya , Petrica Vizureanu , Andrei Victor Sandu , Muhammad Faheem Mohd. Tahir , Alida Abdullah , Liyana Jamaludin

This paper elucidates the mechanical performance, microstructure, and porosity evolution of fly ash geopolymer after 10 years of curing age. Given their wide range of applications, understanding the microstructure of geopolymers is critical for their long-term use. The outcome of fly ash geopolymer on mechanical performance and microstructural characteristics was compared between 28 days of curing (FA28D) and after 10 years of curing age (FA10Y) at similar mixing designs. The results of this work reveal that the FA10Y has a beneficial effect on strength development and denser microstructure compared to FA28D. The total porosity of FA10Y was also lower than FA28D due to the anorthite formation resulting in the compacted matrix. After 10 years of curing age, the 3D pore distribution showed a considerable decrease in the range of 5–30 µm with the formation of isolated and intergranular holes.

View
Thumbnail Image
Publication

Metakaolin/sludge based geopolymer adsorbent on high removal efficiency of Cu2+

2022 , Pilomeena Arokiasamy , Mohd. Mustafa Al Bakri Abdullah , Shayfull Zamree Abd. Rahim , Mohd Remy Rozainy Mohd Arif Zainol , Mohd Arif Anuar Mohd Salleh , Marwan Kheimi , Jitrin Chaiprapa , Andrei Victor Sandu , Petrica Vizureanu , Rafiza Abd Razak , Noorina Hidayu Jamil

Activated carbon (AC) has received a lot of interest from researchers for the removal of heavy metals from wastewater due to its abundant porous structure. However, it was found unable to meet the required adsorption capacity due to its amorphous structure which restricts the fundamental studies and structural optimization for improved removal performance. In addition, AC is not applicable in large scale wastewater treatment due its expensive synthesis and difficulty in regeneration. Thus, the researchers are paying more attention in synthesis of low cost geopolymer based adsorbent for heavy metal removal due its excellent immobilization effect. However, limited studies have focused on the synthesis of geopolymer based adsorbent for heavy metal adsorption by utilizing industrial sludge. Thus, the aim of this research was to develop metakaolin (MK) based geopolymer adsorbent with incorporation of two types of industrial sludge (S1 and S3) that could be employed as an adsorbent for removing copper (Cu2+) from aqueous solution through the adsorption process. The effects of varied solid to liquid ratio (S/L) on the synthesis of metakaolin/sludge based geopolymer adsorbent and the removal efficiency of Cu2+ by the synthesis adsorbent were studied. The raw materials and synthesized geopolymer were characterized by using x-ray fluorescence (XRF), x-ray diffraction (XRD), scanning electron microscope (SEM), fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) and micro XRF. The concentration of Cu2+ before and after adsorption was determined by atomic absorption spectroscopy (AAS) and the removal efficiency was calculated. The experimental data indicated that the synthesized geopolymer at low S/L ratio has achieved the highest removal efficiency of Cu2+ about 99.62 % and 99.37 % at 25 %:75 % of MK/S1 and 25 %:75 % of MK/S3 respectively compared to pure MK based geopolymer with 98.56 %. The best S/

View
Thumbnail Image
Publication

Formation and growth of intermetallic compounds in lead-free solder joints: a review

2022 , Mohd Izrul Izwan Ramli , Mohd Arif Anuar Mohd Salleh , Mohd. Mustafa Al Bakri Abdullah , Nur Syahirah Mohamad Zaimi , Andrei Victor Sandu , Petrica Vizureanu , Adam Rylski , Siti Farahnabilah Muhd Amli

Recently, research into the factors that influence the formation and growth of intermetallic compounds (IMCs) layer in lead-free solders has piqued interest, as IMCs play an important role in solder joints. The reliability of solder joints is critical to the long-term performance of electronic products. One of the most important factors which are known to influence solder joint reliability is the intermetallic compound (IMC) layer formed between the solder and the substrate. Although the formation of an IMC layer signifies good bonding between the solder and substrate, its main disadvantage is due to its brittle nature. This paper reviews the formation and growth of IMCs in lead-free solder joints detailing the effect of alloying additions, surface finishes, aging time, aging temperature and solder volume. The formation and growth of the brittle IMCs were significantly affected by these factors and could be possibly controlled. This review may be used as a basis in understanding the major factors effecting the IMC formation and growth and relating it to the reliability of solder joints.

View
Thumbnail Image
Publication

Recent developments in steelmaking industry and potential alkali activated based steel waste: A comprehensive review

2022 , Ikmal Hakem Aziz , Mohd. Mustafa Al Bakri Abdullah , Mohd Arif Anuar Mohd Salleh , Liew Yun Ming , Long Yuan Li , Andrei Victor Sandu , Petrica Vizureanu , Ovidiu Nemes , Shaik Numan Mahdi

The steel industry is responsible for one-third of all global industrial CO2 emissions, putting pressure on the industry to shift forward towards more environmentally friendly production methods. The metallurgical industry is under enormous pressure to reduce CO2 emissions as a result of growing environmental concerns about global warming. The reduction in CO2 emissions is normally fulfilled by recycling steel waste into alkali-activated cement. Numerous types of steel waste have been produced via three main production routes, including blast furnace, electric arc furnace, and basic oxygen furnace. To date, all of the steel waste has been incorporated into alkali activation system to enhance the properties. This review focuses on the current developments over the last ten years in the steelmaking industry. This work also summarizes the utilization of steel waste for improving cement properties through an alkali activation system. Finally, this work presents some future research opportunities with regard to the potential of steel waste to be utilized as an alkali-activated material.

View
Thumbnail Image
Publication

Contribution of interfacial bonding towards geopolymers properties in geopolymers reinforced fibers: a review

2022 , Muhd Hafizuddin Yazid , Meor Ahmad Faris bin Meor Ahmad Tajudin , Mohd. Mustafa Al Bakri Abdullah , Marcin Nabiałek , Shayfull Zamree Abd. Rahim , Mohd Arif Anuar Mohd Salleh , Marwan Kheimi , Andrei Victor Sandu , Adam Rylski , Bartłomiej Jeż

There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.

View
Thumbnail Image
Publication

Contribution of interfacial bonding towards geopolymers properties in geopolymers reinforced fibers: A review

2022 , Muhd Hafizuddin Yazid , Meor Ahmad Faris bin Meor Ahmad Tajudin , Mohd. Mustafa Al Bakri Abdullah , Marcin Nabiałek , Shayfull Zamree Abd. Rahim , Mohd Arif Anuar Mohd Salleh , Marwan Kheimi , Andrei Victor Sandu , Adam Rylski , Bartłomiej Jeż

There is a burgeoning interest in the development of geopolymers as sustainable construction materials and incombustible inorganic polymers. However, geopolymers show quasi-brittle behavior. To overcome this weakness, hundreds of researchers have focused on the development, characterization, and implementation of geopolymer-reinforced fibers for a wide range of applications for light geopolymers concrete. This paper discusses the rapidly developing geopolymer-reinforced fibers, focusing on material and geometrical properties, numerical simulation, and the effect of fibers on the geopolymers. In the section on the effect of fibers on the geopolymers, a comparison between single and hybrid fibers will show the compressive strength and toughness of each type of fiber. It is proposed that interfacial bonding between matrix and fibers is important to obtain better results, and interfacial bonding between matrix and fiber depends on the type of material surface contact area, such as being hydrophobic or hydrophilic, as well as the softness or roughness of the surface.

View
Thumbnail Image
Publication

Alkaline-Activation technique to produce low-temperature sintering activated-HAp ceramic

2023 , Wan Mohd Arif W Ibrahim , Mohd. Mustafa Al Bakri Abdullah , Noorina Hidayu Jamil , Hasmaliza Mohamad , Mohd Arif Anuar Mohd Salleh , Andrei Victor Sandu , Petrica Vizureanu , Madalina Simona Baltatu , Patimapon Sukmak

The fabrication of hydroxyapatite (HAp) ceramics prepared by existing conventional sintering requires high-temperature sintering of 1250 °C to 1300 °C. In this paper, the activated metakaolin (MK)/HAp specimens were prepared from varied mix design inputs, which were varied solid mixtures (different amounts of MK loading in HAp) and liquid-to-solid (L/S) ratios, before being pressed and sintered at 900 °C. Phase analysis, thermal analysis, surface morphology, and tensile strength of the specimens were investigated to study the influences of the Al, Si, Fe, Na, and K composition on the formation of the hydroxyapatite phase and its tensile strength. XRD analysis results show the formation of different phases was obtained from the different mix design inputs HAp (hexagonal and monoclinic), calcium phosphate, sodium calcium phosphate silicate and calcium hydrogen phosphate hydrate. Interestingly, the specimen with the addition of 30 g MK prepared at a 1.25 L/S ratio showed the formation of a monoclinic hydroxyapatite phase, resulting in the highest diametrical tensile strength of 12.52 MPa. Moreover, the increment in the MK amount in the specimens promotes better densification when sintered at 900 °C, which was highlighted in the microstructure study. This may be attributed to the Fe2O3, Na2O, and K2O contents in the MK and alkaline activator, which acted as a self-fluxing agent and contributed to the lower sintering temperature. Therefore, the research revealed that the addition of MK in the activated-HAp system could achieve a stable hydroxyapatite phase and better tensile strength at a low sintering temperature.

View
Thumbnail Image
Publication

Effects of multiple reflow on the formation of primary crystals in Sn-3.5Ag and solder joint strength: experimental and finite element analysis

2023 , Siti Farahnabilah Muhd Amli , Mohd Arif Anuar Mohd Salleh , Mohd Sharizal Abdul Aziz , Hideyuki Yasuda , Kazuhiro Nogita , Mohd. Mustafa Al Bakri Abdullah , Ovidiu Nemes , Andrei Victor Sandu , Petrica Vizureanu

The growth and formation of primary intermetallics formed in Sn-3.5Ag soldered on copper organic solderability preservative (Cu-OSP) and electroless nickel immersion gold (ENIG) surface finish after multiple reflows were systematically investigated. Real-time synchrotron imaging was used to investigate the microstructure, focusing on the in situ growth behavior of primary intermetallics during the solid–liquid–solid interactions. The high-speed shear test was conducted to observe the correlation of microstructure formation to the solder joint strength. Subsequently, the experimental results were correlated with the numerical Finite Element (FE) modeling using ANSYS software to investigate the effects of primary intermetallics on the reliability of solder joints. In the Sn-3.5Ag/Cu-OSP solder joint, the well-known Cu6Sn5 interfacial intermetallic compounds (IMCs) layer was observed in each reflow, where the thickness of the IMC layer increases with an increasing number of reflows due to the Cu diffusion from the substrate. Meanwhile, for the Sn-3.5Ag/ENIG solder joints, the Ni3Sn4 interfacial IMC layer was formed first, followed by the (Cu, Ni)6Sn5 IMC layer, where the formation was detected after five cycles of reflow. The results obtained from real-time imaging prove that the Ni layer from the ENIG surface finish possessed an effective barrier to suppress and control the Cu dissolution from the substrates, as there is no sizeable primary phase observed up to four cycles of reflow. Thus, this resulted in a thinner IMC layer and smaller primary intermetallics, producing a stronger solder joint for Sn-3.5Ag/ENIG even after the repeated reflow process relative to the Sn-3.5Ag/Cu-OSP joints.

View
Thumbnail Image
Publication

The influence of sintering temperature on the pore structure of an Alkali-Activated Kaolin-Based Geopolymer Ceramic

2022 , Mohd Izrul Izwan Ramli , Mohd Arif Anuar Mohd Salleh , Mohd. Mustafa Al Bakri Abdullah , Ikmal Hakem Aziz , Tan Chi Ying , Noor Fifinatasha Shahedan , Winfried Kockelmann , Anna Fedrigo , Andrei Victor Sandu , Petrica Vizureanu , Jitrin Chaiprapa , Dumitru Doru Burduhos Nergis

Geopolymer materials are used as construction materials due to their lower carbon dioxide (CO2) emissions compared with conventional cementitious materials. An example of a geopolymer material is alkali-activated kaolin, which is a viable alternative for producing high-strength ceramics. Producing high-performing kaolin ceramics using the conventional method requires a high processing temperature (over 1200 °C). However, properties such as pore size and distribution are affected at high sintering temperatures. Therefore, knowledge regarding the sintering process and related pore structures on alkali-activated kaolin geopolymer ceramic is crucial for optimizing the properties of the aforementioned materials. Pore size was analyzed using neutron tomography, while pore distribution was observed using synchrotron micro-XRF. This study elucidated the pore structure of alkali-activated kaolin at various sintering temperatures. The experiments showed the presence of open pores and closed pores in alkali-activated kaolin geopolymer ceramic samples. The distributions of the main elements within the geopolymer ceramic edifice were found with Si and Al maps, allowing for the identification of the kaolin geopolymer. The results also confirmed that increasing the sintering temperature to 1100 °C resulted in the alkali-activated kaolin geopolymer ceramic samples having large pores, with an average size of ~80 µm3 and a layered porosity distribution.

View
Thumbnail Image
Publication

Metakaolin/sludge based geopolymer adsorbent on high removal efficiency of Cu2+

2022 , Pilomeena Arokiasamy , Mohd. Mustafa Al Bakri Abdullah , Shayfull Zamree Abd. Rahim , Mohd Remy Rozainy Mohd Arif Zainol , Mohd Arif Anuar Mohd Salleh , Marwan Kheimi , Andrei Victor Sandu , Petrica Vizureanu , Rafiza Abdul Razak , Noorina Hidayu Jamil

Activated carbon (AC) has received a lot of interest from researchers for the removal of heavy metals from wastewater due to its abundant porous structure. However, it was found unable to meet the required adsorption capacity due to its amorphous structure which restricts the fundamental studies and structural optimization for improved removal performance. In addition, AC is not applicable in large scale wastewater treatment due its expensive synthesis and difficulty in regeneration. Thus, the researchers are paying more attention in synthesis of low cost geopolymer based adsorbent for heavy metal removal due its excellent immobilization effect. However, limited studies have focused on the synthesis of geopolymer based adsorbent for heavy metal adsorption by utilizing industrial sludge. Thus, the aim of this research was to develop metakaolin (MK) based geopolymer adsorbent with incorporation of two types of industrial sludge (S1 and S3) that could be employed as an adsorbent for removing copper (Cu²⁺) from aqueous solution through the adsorption process. The effects of varied solid to liquid ratio (S/L) on the synthesis of metakaolin/sludge based geopolymer adsorbent and the removal efficiency of Cu²⁺ by the synthesis adsorbent were studied. The raw materials and synthesized geopolymer were characterized by using x-ray fluorescence (XRF), x-ray diffraction (XRD), scanning electron microscope (SEM), fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) and micro XRF. The concentration of Cu²⁺ before and after adsorption was determined by atomic absorption spectroscopy (AAS) and the removal efficiency was calculated. The experimental data indicated that the synthesized geopolymer at low S/L ratio has achieved the highest removal efficiency of Cu²⁺ about 99.62% and 99.37% at 25%:75% of MK/S1 and 25%:75% of MK/S3 respectively compared to pure MK based geopolymer with 98.56%. The best S/L ratio for MK/S1 and MK/S3 is 0.6 at which the reaction between the alkaline activator and the aluminosilicate materials has improved and enhanced the geopolymerization process. Finally, this work clearly indicated that industrial sludge can be utilized in developing low-cost adsorbent with high removal efficiency

View