Azremi Abdullah Al-Hadi
Thumbnail Image
Preferred name
Azremi Abdullah Al-Hadi
Official Name
Azremi, Abdullah Al-Hadi
Alternative Name
Abdullah Al-Hadi, Azremi
Al-Hadi, Azremi A.
Al-Hadi, A. A.
Azremi, A. A. H.
Main Affiliation
Scopus Author ID
57194469675
Researcher ID
A-6983-2015

Research Output

Filters

4
Reset filters

Settings
Now showing 1 - 4 of 4
Thumbnail Image
Publication

Deployable Linear-to-Circular Polarizer Using PDMS Based on Unloaded and Loaded Circular FSS Arrays for Pico-Satellites

2019 , Hidayath Mirza , Toufiq Md Hossain , Ping Jack Soh , Mohd Faizal Jamlos , Muhammad Nazrin Ramli , Azremi Abdullah Al-Hadi , Emad S. Hassan , Sen Yan

In this paper, flexible and deployable double-sided linear-to-circular polarizers designed on polydimethylsiloxane are proposed for the first time to the best of our knowledge. ShieldIt textile is used as the conducting element of the two designs based on two different unit cell arrays: a loaded circular patch unit cell or an unloaded circular patch unit cell, both backed by a generic rectangular element on its reverse side. This is in contrast to conventional frequency-selective structure-based linear-to-circular polarizers implemented using rigid substrates, which are multi-layered and requires inter-layer physical spacing. This complicates their implementation using flexible substrates and in a deployable format. Upon implementation of this double-sided polarizer, their final performances are evaluated in terms of the phase difference, conversion efficiency, 3-dB axial ratio (AR), and ellipticity bandwidth (from 40° to 45°). Measurements indicated good agreements with simulations, and both structures exhibited more than 90% of conversion efficiency from 2.34 to 3 GHz (for the loaded circular unit cell) and from 2.36 to 3 GHz (for the unloaded circular unit cell). In terms of ellipticity, a bandwidth of 8.67% is observed for the unloaded design and 13.82% for the loaded design. The unloaded structure exhibited a fractional 3-dB AR bandwidth of 36.36% (from 1.98 to 2.86 GHz) in simulations, and 32.64 % (from 2.00 to 2.78 GHz) when evaluated experimentally. Conversely, the loaded design showed only 12.58%. An equivalent circuit model is proposed and validated via a comparison between the circuit and full-wave simulations. Finally, the performances of these polarizers are also assessed under different bending conditions due to the use of flexible materials, prior to the proposal of a suitable deployment mechanism.

View
Thumbnail Image
Publication

Dual Band Planar Inverted F Antenna (PIFA) with L-Shape Configuration

2017 , Mohamad khlouf Munzer , Saidatul Norlyana Azemi , Ping Jack Soh , Azremi Abdullah Al-Hadi , Mohd Faizal Jamlos

One of the most used antennas in mobile devices is planar inverted F antenna (PIFA). PIFA can be design in dual band frequencies due to the coverage of the wireless service in a mobile device that requires a multiple frequencies. However, the consideration of technical operation has to be combined with an evaluation of the antenna radiation impact on the users. A procedure of PIFA work in GSM (867-960MHz) and GSM (1710-1899MHz) is done using CST Software. The dual band frequency response is obtained by means of an insertion of an L-shaped slot, which is use to tune the operation frequencies. The prototype of the antenna is fabricated as model by CST Software and evaluated. It is found out that the PIFA antenna has a good efficiency, bandwidth as well as produce a maximum gain for the antenna. A key and innovative research is still underway to broaden performance parameters of the antenna.

View
No Thumbnail Available
Publication

Dual-band, dual-sense textile antenna with AMC backing for localization using GPS and WBAN/WLAN

2020 , Rahil Joshi , Ezzaty Faridah Nor Mohd Hussin , Ping Jack Soh , Mohd Faizal Jamlos , Herwansyah Lago , Azremi Abdullah Al-Hadi , Symon K. Podilchak

A wearable textile antenna with dual-band and dual-sense characteristics is presented in this work. It operates at the 2.45 GHz band for WBAN and WLAN applications, and at the 1.575 GHz band for Global Positioning System (GPS) applications. An antenna backing based on an artificial magnetic conductor (AMC) plane operating at 2.45 GHz band is introduced to reduce the backward radiation and to improve antenna gain. It consists of a 3×3 array of square patch unit cells, where each unit cell is integrated with four square slits and a square ring. A square-shaped patch is then located on top of the substrate as its radiator. To enable dual-band operation, two corners of this radiator are truncated, with each of the four corners incorporated with a rectangular slit to enable its circular polarization characteristic in the GPS band. Simulation and experimental results are in good agreement and indicate proper antenna operation with linear polarization in the 2.45 GHz band and circular polarization in the 1.575 GHz band, with realized gain of 1.94 dBi and 1.98 dBic, respectively.

View
Thumbnail Image
Publication

A Review of Antennas for Picosatellite Applications

2017 , Abdul Halim Lokman , Ping Jack Soh , Saidatul Norlyana Azemi , Herwansyah Lago , Symon K. Podilchak , Suramate Chalermwisutkul , Mohd Faizal Jamlos , Azremi Abdullah Al-Hadi , Prayoot Akkaraekthalin , Steven Gao

Cube Satellite (CubeSat) technology is an attractive emerging alternative to conventional satellites in radio astronomy, earth observation, weather forecasting, space research, and communications. Its size, however, poses a more challenging restriction on the circuitry and components as they are expected to be closely spaced and very power efficient. One of the main components that will require careful design for CubeSats is their antennas, as they are needed to be lightweight, small in size, and compact or deployable for larger antennas. This paper presents a review of antennas suitable for picosatellite applications. An overview of the applications of picosatellites will first be explained, prior to a discussion on their antenna requirements. Material and antenna topologies which have been used will be subsequently discussed prior to the presentation of several deployable configurations. Finally, a perspective and future research work on CubeSat antennas will be discussed in the conclusion.

View