Shayfull Zamree Abd. Rahim
Thumbnail Image
Preferred name
Shayfull Zamree Abd. Rahim
Official Name
Shayfull Zamree, Abd. Rahim
Alternative Name
Shayfull, Zamree Abd Rahim
Abd Rahim, Shayfull Zamree Abd
Shayfull, Zamree
Abd Rahim, S. Z.
Abd Rahim, Shayfull Zamree Bin
Bin Abd Rahim, S. Zamree
Abd Rahim, S.
zamree bin abd Rahim, Shayfull
Rahim, Shayfull Zamree Abd
Zamree Abd Rahim, Shayfull
Zambree, Shayfull
Rahim, Shayfull Z.B.Abd
Zamree, A. R.Shayfull
Shayfull, Z.
Main Affiliation
Scopus Author ID
54941291700
Researcher ID
I-2840-2019

Research Output
Now showing 1 - 7 of 7
Thumbnail Image
Publication

Optimisation of shrinkage and strength on thick plate part using recycled LDPE materials

2021 , Norshahira Roslan , Shayfull Zamree Abd. Rahim , Abdellah El-hadj Abdellah , Mohd. Mustafa Al Bakri Abdullah , Katarzyna Błoch , Paweł Pietrusiewicz , Marcin Nabiałek , Janusz Szmidla , Dariusz Kwiatkowski , Joel Oliveira Correia Vasco , Mohd. Nasir Mat Saad , Mohd Fathullah Ghazli@Ghazali

Achieving good quality of products from plastic injection moulding processes is very challenging, since the process comprises many affecting parameters. Common defects such as warpage are hard to avoid, and the defective parts will eventually go to waste, leading to unnecessary costs to the manufacturer. The use of recycled material from postindustrial waste has been studied by a few researchers. However, the application of an optimisation method by which to optimise processing parameters to mould parts using recycled materials remains lacking. In this study, Response Surface Methodology (RSM) and Particle Swarm Optimisation (PSO) methods were conducted on thick plate parts moulded using virgin and recycled low-density polyethylene (LDPE) materials (100:0, 70:30, 60:40 and 50:50; virgin to recycle material ratios) to find the optimal input parameters for each of the material ratios. Shrinkage in the x and y directions increased in correlation with the recycled ratio, compared to virgin material. Meanwhile, the tensile strength of the thick plate part continued to decrease when the recycled ratio increased. R30 (70:30) had the optimum shrinkage in the x direction with respect to R0 (100:0) material where the shrinkage increased by 24.49% (RSM) and 33.20% (PSO). On the other hand, the shrinkage in the y direction for R30 material increased by 4.48% (RSM) and decreased by 2.67% (PSO), while the tensile strength of R30 (70:30) material decreased by 0.51% (RSM) and 2.68% (PSO) as compared to R0 (100:0) material. Validation tests indicated that the optimal setting of processing parameter suggested by PSO and RSM for R0 (100:0), R30 (70:30), R40 (60:40) and R50 (50:50) was less than 10%.

View
Thumbnail Image
Publication

Potential of Rapid Tooling in rapid heat cycle molding: a review

2022 , Nurul Hidayah Mohamad Huzaim , Shayfull Zamree Abd. Rahim , Luqman Musa , Abdellah El-hadj Abdellah , Mohd. Mustafa Al Bakri Abdullah , Allan Rennie , Rozyanty Rahman , Sebastian Garus , Katarzyna Błoch , Andrei Victor Sandu , Petrica Vizureanu , Marcin Nabiałek

Rapid tooling (RT) and additive manufacturing (AM) are currently being used in several parts of industry, particularly in the development of new products. The demand for timely deliveries of low-cost products in a variety of geometrical patterns is continuing to increase year by year. Increased demand for low-cost materials and tooling, including RT, is driving the demand for plastic and rubber products, along with engineering and product manufacturers. The development of AM and RT technologies has led to significant improvements in the technologies, especially in testing performance for newly developed products prior to the fabrication of hard tooling and low-volume production. On the other hand, the rapid heating cycle molding (RHCM) injection method can be implemented to overcome product surface defects generated by conventional injection molding (CIM), since the surface gloss of the parts is significantly improved, and surface marks such as flow marks and weld marks are eliminated. The most important RHCM technique is rapid heating and cooling of the cavity surface, which somewhat improves part quality while also maximizing production efficiencies. RT is not just about making molds quickly; it also improves molding productivity. Therefore, as RT can also be used to produce products with low-volume production, there is a good potential to explore RHCM in RT. This paper reviews the implementation of RHCM in the molding industry, which has been well established and undergone improvement on the basis of different heating technologies. Lastly, this review also introduces future research opportunities regarding the potential of RT in the RHCM technique.

View
Thumbnail Image
Publication

Producing metal powder from machining chips using ball milling process: a review

2023 , Leong Kean Wei , Shayfull Zamree Abd. Rahim , Mohd. Mustafa Al Bakri Abdullah , Allice Yin , Mohd Fathullah Ghazli@Ghazali , Mohd Nazri Omar , Ovidiu NemeÈ™ , Andrei Sandu , Petrica Vizureanu , Abdellah Abdellah

In the pursuit of achieving zero emissions, exploring the concept of recycling metal waste from industries and workshops (i.e., waste-free) is essential. This is because metal recycling not only helps conserve natural resources but also requires less energy as compared to the production of new products from virgin raw materials. The use of metal scrap in rapid tooling (RT) for injection molding is an interesting and viable approach. Recycling methods enable the recovery of valuable metal powders from various sources, such as electronic, industrial, and automobile scrap. Mechanical alloying is a potential opportunity for sustainable powder production as it has the capability to convert various starting materials with different initial sizes into powder particles through the ball milling process. Nevertheless, parameter factors, such as the type of ball milling, ball-to-powder ratio (BPR), rotation speed, grinding period, size and shape of the milling media, and process control agent (PCA), can influence the quality and characteristics of the metal powders produced. Despite potential drawbacks and environmental impacts, this process can still be a valuable method for recycling metals into powders. Further research is required to optimize the process. Furthermore, ball milling has been widely used in various industries, including recycling and metal mold production, to improve product properties in an environmentally friendly way. This review found that ball milling is the best tool for reducing the particle size of recycled metal chips and creating new metal powders to enhance mechanical properties and novelty for mold additive manufacturing (MAM) applications. Therefore, it is necessary to conduct further research on various parameters associated with ball milling to optimize the process of converting recycled copper chips into powder. This research will assist in attaining the highest level of efficiency and effectiveness in particle size reduction and powder quality. Lastly, this review also presents potential avenues for future research by exploring the application of RT in the ball milling technique.

View
Thumbnail Image
Publication

Warpage optimisation using recycled Polycar-bonates (PC) on front panel housing

2021 , Nur Aisyah Miza Ahmad Tamizi , Shayfull Zamree Abd. Rahim , Abdellah El-hadj Abdellah , Mohd. Mustafa Al Bakri Abdullah , Marcin Nabiałek , Jerzy J. Wysłocki , Bartłomiej Jeż , Paweł Palutkiewicz , Rozyanty Abdul Rahman , Mohd. Nasir Mat Saad , Mohd Fathullah Ghazli@Ghazali

Many studies have been done using recycled waste materials to minimise environmental problems. It is a great opportunity to explore mechanical recycling and the use of recycled and virgin blend as a material to produce new products with minimum defects. In this study, appropriate processing parameters were considered to mould the front panel housing part using R0% (virgin), R30% (30% virgin: 70% recycled), R40% (40% virgin: 60% recycled) and R50% (50% virgin: 50% recycled) of Polycarbonate (PC). The manufacturing ability and quality during preliminary stage can be predicted through simulation analysis using Autodesk Moldflow Insight 2012 software. The recommended processing parameters and values of warpage in x and y directions can also be obtained using this software. No value of warpage was obtained from simulation studies for x direction on the front panel housing. Therefore, this study only focused on reducing the warpage in the y direction. Response Surface Methodology (RSM) and Genetic Algorithm (GA) optimisation methods were used to find the optimal processing parameters. As the results, the optimal ratio of recycled PC material was found to be R30%, followed by R40% and R50% materials using RSM and GA methods as compared to the average value of warpage on the moulded part using R0%. The most influential processing parameter that contributed to warpage defect was packing pressure for all materials used in this study.

View
Thumbnail Image
Publication

Warpage optimisation using Recycled Polycar-bonates (PC) on Front Panel Housing

2021 , Nur Aisyah Miza Ahmad Tamizi , Shayfull Zamree Abd. Rahim , Abdellah El-hadj Abdellah , Mohd. Mustafa Al Bakri Abdullah , Marcin Nabiałek , Jerzy J. Wysłocki , Bartłomiej Jeż , Paweł Palutkiewicz , Rozyanty Abdul Rahman , Mohd. Nasir Mat Saad , Mohd Fathullah Ghazli@Ghazali

Many studies have been done using recycled waste materials to minimise environmental problems. It is a great opportunity to explore mechanical recycling and the use of recycled and virgin blend as a material to produce new products with minimum defects. In this study, appropriate processing parameters were considered to mould the front panel housing part using R0% (virgin), R30% (30% virgin: 70% recycled), R40% (40% virgin: 60% recycled) and R50% (50% virgin: 50% recycled) of Polycarbonate (PC). The manufacturing ability and quality during preliminary stage can be predicted through simulation analysis using Autodesk Moldflow Insight 2012 software. The recommended processing parameters and values of warpage in x and y directions can also be obtained using this software. No value of warpage was obtained from simulation studies for x direction on the front panel housing. Therefore, this study only focused on reducing the warpage in the y direction. Response Surface Methodology (RSM) and Genetic Algorithm (GA) optimisation methods were used to find the optimal processing parameters. As the results, the optimal ratio of recycled PC material was found to be R30%, followed by R40% and R50% materials using RSM and GA methods as compared to the average value of warpage on the moulded part using R0%. The most influential processing parameter that contributed to warpage defect was packing pressure for all materials used in this study.

View
Thumbnail Image
Publication

Warpage optimisation on the moulded part with straight drilled and conformal cooling channels using Response Surface Methodology (RSM), Glowworm Swarm Optimisation (GSO) and Genetic Algorithm (GA) optimisation approaches

2021 , Mohd. Hazwan Mohd. Hanid , Shayfull Zamree Abd. Rahim , Joanna Gondro , Safian Sharif , Mohd. Mustafa Al Bakri Abdullah , Azlan Mohd Zain , Abdellah El-hadj Abdellah , Mohd. Nasir Mat Saad , Jerzy J. Wysłocki , Marcin Nabiałek

It is quite challenging to control both quality and productivity of products produced using injection molding process. Although many previous researchers have used different types of optimisation approaches to obtain the best configuration of parameters setting to control the quality of the molded part, optimisation approaches in maximising the performance of cooling channels to enhance the process productivity by decreasing the mould cycle time remain lacking. In this study, optimisation approaches namely Response Surface Methodology (RSM), Genetic Algorithm (GA) and Glowworm Swarm Optimisation (GSO) were employed on front panel housing moulded using Acrylonitrile Butadiene Styrene (ABS). Each optimisation method was analysed for both straight drilled and Milled Groove Square Shape (MGSS) conformal cooling channel moulds. Results from experimental works showed that, the performance of MGSS conformal cooling channels could be enhanced by employing the optimisation approach. Therefore, this research provides useful scientific knowledge and an alternative solution for the plastic injection moulding industry to improve the quality of moulded parts in terms of deformation using the proposed optimisation approaches in the used of conformal cooling channels mould.

View
Thumbnail Image
Publication

Irregular shape effect of brass and copper filler on the properties of Metal Epoxy Composite (MEC) for rapid tooling application

2022 , Radhwan Hussin , Safian Sharif , Shayfull Zamree Abd. Rahim , Allan Rennie , Mohd Azlan Suhaimi , Abdellah El-hadj Abdellah , Norshah Afizi Shuaib , Mohd Tanwyn Mohd Khushairi , Aurel Mihail Titu

Due to their low shrinkage and easy moldability, metal epoxy composites (MEC) are recognized as an alternative material that can be applied as hybrid mold inserts manufactured with rapid tooling (RT) technologies. Although many studies have been conducted on MEC or reinforced composite, research on the material properties, especially on thermal conductivity and compressive strength, that contribute to the overall mold insert performance and molded part quality are still lacking. The purpose of this research is to investigate the effect of the cooling efficiency using MEC materials. Thus, this research aims to appraise a new formulation of MEC materials as mold inserts by further improving the mold insert performance. The effects of the thermal, physical, and mechanical properties of MEC mold inserts were examined using particles of brass (EB), copper (EC), and a combination of brass + copper (EBC) in irregular shapes. These particles were weighed at percentages ranging from 10% to 60% when mixed with epoxy resin to produce specimens according to related ASTM standards. A microstructure analysis was made using a scanning electron microscope (SEM) to investigate brass and copper particle distribution. When filler composition was increased from 10% to 60%, the values of density (g/cm3), hardness (Hv), and thermal conductivity (W/mK) showed a linear upward trend, with the highest value occurring at the highest filler composition percentage. The addition of filler composition increased the compressive strength, with the highest average compressive strength value occurring between 20% and 30% filler composition. Compressive strength indicated a nonlinear uptrend and decreased with increasing composition by more than 30%. The maximum value of compressive strength for EB, EC, and EBC was within the range of 90–104 MPa, with EB having the highest value (104 MPa). The ANSYS simulation software was used to conduct a transient thermal analysis in order to evaluate the cooling performance of the mold inserts. EC outperformed the EB and EBC in terms of cooling efficiency based on the results of thermal transient analysis at high compressive strength and high thermal conductivity conditions.

View