Azliza Azani
Thumbnail Image
Preferred name
Azliza Azani
Official Name
Azani, Azliza
Alternative Name
Azani, Azliza
Azani, A.
Main Affiliation
Scopus Author ID
57210390723
Researcher ID
CCW-3693-2022

Research Output

Filters

1
3
Reset filters

Settings
Now showing 1 - 3 of 3
Thumbnail Image
Publication

The effect of polyethylene glycol addition on wettability and optical properties of GO/TiO2 thin film

2021 , Azliza Azani , Dewi Suriyani Che Halin , Kamrosni Abdul Razak , Mohd. Mustafa Al Bakri Abdullah , Marcin Nabiałek , Muhammad Mahyiddin Ramli , Mohd Fairul Sharin Abdul Razak , Andrei Victor Sandu , Wojciech Sochacki , Tomasz Skrzypczak

Modification has been made to TiO2 thin film to improve the wettability and the absorption of light. The sol-gel spin coating method was successfully used to synthesize GO/TiO2 thin films using a titanium (IV) isopropoxide (TTIP) as a precursor. Different amounts of polyethylene glycol (PEG) (20 to 100 mg) were added into the parent sol solution to improve the optical properties and wettability of the GO/TiO2 thin film. The effect of different amounts of PEG was characterized using X-ray diffraction (XRD) for the phase composition, scanning electron microscopy (SEM) for microstructure observation, atomic force microscopy (AFM) for the surface topography, ultraviolet–visible spectrophotometry (UV-VIS) for the optical properties and wettability of the thin films by measuring the water contact angle. The XRD analysis showed the amorphous phase. The SEM and AFM images revealed that the particles were less agglomerated and surface roughness increases from 1.21 × 102 to 2.63 × 102 nm when the amount of PEG increased. The wettability analysis results show that the water contact angle of the thin film decreased to 27.52° with the increase of PEG to 80 mg which indicated that the thin film has hydrophilic properties. The optical properties also improved significantly, where the light absorbance wavelength became wider and the band gap was reduced from 3.31 to 2.82 eV with the presence of PEG.

View
Thumbnail Image
Publication

The Effect of GO/TiO2 Thin Film During Photodegradation of Methylene Blue Dye

2021 , Azliza Azani , Dewi Suriyani Che Halin , Mohd. Mustafa Al Bakri Abdullah , Kamrosni Abdul Razak , Mohd Fairul Sharin Abdul Razak , V Chobpattana , Mohd Arif Anuar Mohd Salleh , Muhammad Mahyiddin Ramli

Titanium (IV) isopropoxide (TTIP) was used to synthesize GO/TiO2 thin films using a sol-gel spin-coating method onto a glass substrate, undergoing an heat tretment at 350 °C. Several amounts of graphene oxide (GO) (0-20mg) were weighed into a sol solution of TiO2 to produce GO/TiO2 thin films. The thin film samples were characterized by X-ray diffraction (XRD) to analyze the samples’ phase and by scanning electron microscopy (SEM) to analyze the samples’ microstructure. Physical testing such as water contact angle (WCA) was analyzed using an optical microscope with J-Image software. In contrast, the optical band gap and photodegradation of methylene blue under sunlight irradiation of the thin film was analyzed using UV-VIS spectrophotometry. GO5 thin film sample showed low-intensity anatase phase formation, where the microstructure revealed a larger surface area with the addition of GO. WCA reveals that GO/TiO2 thin film exhibits super hydrophilic properties where the angle decreases from 37.83° to 4.11°. The optical result shows that GO has improved the absorption edges by expanding into visible regions. Moreover, due to the existence of GO 3.30 eV band gap energy of TiO2 decreases from to 3.18 eV obtained by GO5. The improved adsorption edge allows Ti3+, O2 and interstitial states to be formed in low valence states with energy underneath than in the TiO2 band gap. Therefore, the photodegradation of methylene blue (MB) dye increases from 48 % to 59 % in the GO/TiO2 thin film.

View
Thumbnail Image
Publication

Surface Modification of GO/TiO2 Thin Film by Sodium Dodecyl Sulphate for Photocatalytic Applications

2024-01-01 , Azliza Azani , Dewi Suriyani Che Halin , Vizureanu P. , Mohd Arif Anuar Mohd Salleh , Kamrosni Abdul Razak , Mohd. Mustafa Al Bakri Abdullah , Muhammad Mahyiddin Ramli , Mohd Fairul Sharin Abdul Razak , Sandu A.V. , Mohamad N.

Photocatalyst material titanium dioxide (TiO2) and graphene oxide (GO) were used to improve the self-cleaning properties of thin films. The sol–gel spin-coating method was successfully used to synthesize GO/TiO2 thin films. Surface modification was applied to optimize the self-cleaning capabilities by adding several concentrations of sodium dodecyl sulfate (SDS) (0.1 w/v%, 0.2 w/v%, 0.3 w/v%, 0.4 w/v%, and 0.5 w/v%) to the parent solution. The synthesized thin films were investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction, UV-visible spectroscopy, water contact angle analysis, and photocatalytic analysis. The AFM and SEM images revealed that as the SDS amount increased, the particles became less agglomerated, and the roughness of the surface reduced from 2.54 × 102 nm to 0.83 × 102 nm. The wettability analysis showed that when SDS increased to 0.4 w/v%, the water contact angle dropped to 15.30°, implying that the thin film exhibits hydrophilic qualities. A decrease in the GO/TiO2 band gap was obtained linearly with the increase in SDS addition from 3.17 eV to 2.75 eV. Finally, the improvement of the surface coating and reduction of the band gap enhanced the photocatalytic activity, which degraded 78.97% of methylene blue, which was obtained by 0.4SDS.

View