Mohd Riduan Jamalludin
Thumbnail Image
Preferred name
Mohd Riduan Jamalludin
Official Name
Mohd Riduan , Jamalludin
Alternative Name
Jamalludin, M. R.
Riduan Jamalludin, Mohd
Main Affiliation
Scopus Author ID
55778617300
Researcher ID
M-4808-2019
AAU-5306-2020

Research Output

Filters

5
5
5
Reset filters

Settings
Now showing 1 - 5 of 5
  • Publication
    Effect of heat sink design on the thermal characteristic in computational fluid dynamics analysis
    ( 2020-12-18)
    Khor Chu Yee
    ;
    Mohd Al-Hafiz Mohd Nawi
    ;
    Ishak M.I.
    ;
    Kee W.C.
    ;
    Rosli M.U.
    ;
    Mohd Riduan Jamalludin
    ;
    Siti Nor Azreen Ahmad Termizi
    The thermal management in the electronic device or system using the heat sink is important to ensure the device or system operating under the allowable temperature. The present study aims to investigate the thermal characteristic (i.e., temperature distribution) of the various heat sink designs via computational fluid dynamics (CFD) analysis. The electronic cooling process of the heat sink is carried out via CFD software. The temperature distribution of the various heat sink designs (i.e., plate fin, circular pin fin and rectangular fin) was analyzed and compared. The CFD analysis revealed the plate fin heat sink has lowest temperature distribution on the fin region. High temperature distribution was observed on the pin fin heat sink. The non-uniform temperature distribution was attributed by the direction of inlet airflow, whereas the low temperature was found in the region that close to the inlet airflow. Thus, the research findings indicated the design of heat sink significantly affects the temperature distribution during the electronic cooling process.
  • Publication
    The effect of silica toward polymer membrane for water separation process
    ( 2017-09-26)
    Mohd Riduan Jamalludin
    ;
    Rosli M.U.
    ;
    Muhammad Ikman Ishak
    ;
    Khor Chu Yee
    ;
    Mohamad Suhaimi Shahrin
    ;
    Ras Izzati Ismail
    ;
    Lailina N.M.
    ;
    Leng Y.L.
    ;
    Hazrin Jahidi Jaafar
    The aim of this present work was to investigate the effect of different percentage rice husk silica (RHS) particles composition towards polymer mixed matrix membrane microstructure and performance in water separation process. The polymer membranes were prepared by a phase inversion method using polysulfone (PSf), N-methyl-2-pyrrolidone (NMP) as solvent, distilled water as non-solvent and fixed RHS at 400°C as an additive. The microstructures of PSf/PEG/RHS sample were characterized by performing scanning electron microscope (SEM). The performance was measured by using pure water flux and humic acid for the rejection test. The analyzed result of SEM analysis revealed that the addition of RHS obviously improved the microstructure of the membrane especially at the top and sub layer at the range of 1 until 3 wt. %. This was proven by the pure water flux (PWF) value measured from 114.47 LMH to 154.04 LMH and rejection from value 83% to 96% at this specified range substantially higher than the mixed matrix membrane with synthetic silica. In fact, the presence of RHS particles not only improved the properties and performance of membrane but also possess biodegradable properties which can minimize the pollution and provide a membrane green technology system.
  • Publication
    Effect of twist blade distributor on velocity distribution in a swirling fluidized bed
    ( 2020-12-18)
    Mohd Al-Hafiz Mohd Nawi
    ;
    Ishak M.I.
    ;
    Rosli M.U.
    ;
    Suhaida Rasman S.N.
    ;
    Mohd Riduan Jamalludin
    ;
    Siti Nor Azreen Ahmad Termizi
    ;
    Khor Chu Yee
    Swirling Fluidized Bed (SFB) is one of the liquid-solid interaction in fluidization improved from conventional systems. This system is usually viewable in the power generation, chemical industry, material production and drying processes. Inside the SFB, there is annular blade distributor which will cause the air to pass through and create a swirl motion on the bed. The energy consumption of a fluidized bed system depends on the distributor's design. The current study has purpose a new design that applies to existing designs of blade inclination angle. The simulation study was conducted using Computational Fluid Dynamics (CFD) to obtain the result of velocity distribution and pressure drops on various blade distributor designs. This study uses two (2) twist angle (80 and 100 ) via number of blade distributor (40, 50 and 60). In this study, tangential velocity is the main velocity component by reason of the velocity represents the rotating air velocity in fluidization system. Overall, the design of the 100 twist angle and 40 blades distributor are the best distributors of blades compared to others.
      3  22
  • Publication
    The modified phase inversion and sintering technique for fabrication of ceramic membrane: Influence of kaolin composition and drying temperature
    ( 2021-05-03)
    Mohd Riduan Jamalludin
    ;
    Siti Nor Azreen Ahmad Termizi
    ;
    Khor Chu Yee
    ;
    Hubadillah S.K.
    ;
    Mohd Al-Hafiz Mohd Nawi
    ;
    Ishak M.I.
    ;
    Rosli M.U.
    The practical use of ceramic membrane has been limited by their fabrication technique and brittleness. Nowadays, phase inversion and sintering technique for ceramic membrane fabrication has been received widely attention. However, the unavoidable unstable structure for fabrication of flat-sheet ceramic membrane using this technique is still becoming an issue. To overcome this problem, in this paper, flat-sheet ceramic membrane have been developed via modified phase inversion and sintering technique using kaolin as main ceramic material, polyethersulfone (PESf) as the polymeric binder and N-methylpyyrolidone (NMP) as the solvent, respectively. The modified phase inversion has been done by adding drying process before the immersion into solvent. The influence of kaolin composition (60-80g) and drying temperature (room temperature and 3oC) have been investigated extensively to optimize the preparation. The results showed that the ceramic membrane prepared at 80g kaolin composition with drying temperature of 3oC displayed the highest bending strength of 53.1g with excellent BSA and humic acid rejection. Therefore, this study proved that the problem of unstable fabrication technique for flat-sheet ceramic membrane can be solved via modified phase inversion through the influence of high composition and low drying temperature.
      17  3
  • Publication
    Effect of zinc addition on the performance of aluminium alloy sacrificial anode for marine application
    ( 2017-09-26)
    Khan B.
    ;
    Rosli M.U.
    ;
    Hazrin Jahidi Jaafar
    ;
    Muhammad Ikman Ishak
    ;
    Muhammad Syamil Zakaria
    ;
    Mohd Riduan Jamalludin
    ;
    Khor Chu Yee
    ;
    Wan Mohd Faizal Wan Ab Rahim
    ;
    Rahim W.M.
    ;
    Mohd Al-Hafiz Mohd Nawi
    In this work, the effect of zinc addition on the performance of aluminum-based sacrificial anode in seawater was investigated. The parameters used in assessing the performance of the cast anodes are anodic efficiency, protection efficiency and polarized potential. The content of zinc in the anodes was varied after die casting. The alloys produced were tested as sacrificial anode for the protection of mild steel for marine application at room temperature. Factors such as reactivity of zinc particles in the seawater, corrosion activity during the period of experiment, pH of seawater and the electronegativity potential of zinc were collected for analysis. Overall findings shows addition of zinc increases rate of corrosion to the sacrificial anode and the protection offered by the sacrificial anodes measured and collected in PIT shows the seawater react to sacrificial anode and no porosity reaction between the anodes. The microstructure showed the intermetallic structures of β-phase which breakdown the alumina passive film, thus enhancing the anode efficiency.
      32  2