Mohd Fairus Ahmad
Thumbnail Image
Preferred name
Mohd Fairus Ahmad
Official Name
Mohd Fairus , Ahmad
Alternative Name
Shahimin, Mohd Faidz Mohamad
Mohamad Shahimin, M. F.
Main Affiliation
Scopus Author ID
57006554500
Researcher ID
B-9547-2018

Research Output

Filters

6
6
Reset filters

Settings
Now showing 1 - 6 of 6
  • Publication
    The effect of solvents on the performance of organic light-emitting diodes
    ( 2020-01-08)
    Ismail N.A.N.
    ;
    Safizan Shaari
    ;
    Juhari N.
    ;
    Norhayati Sabani
    ;
    Mohd Fairus Ahmad
    ;
    Zakaria N.F.
    In this paper, we investigate the solvent effect on the performance of surface roughness, absorption spectrum of MEH-PPV thin films and J-V characteristics for MEH-PPV OLED device. The 5 mg emissive layer of poly [2-methoxy-5(2' -ethylhexyloxy)-1, 4-phenylenevinylene), MEH-PPV was diluted with 1ml toluene and 1 ml different mixture of solvent (80% toluene+20 % chloroform) which gives the concentration of 5 mgml-1 respectively. The surface roughness of MEH-PPV film was reduced to 0.3 nm and the red-shifted maximum peak wavelength value were obtained when mixture solvent was used. However, J-V gives higher turn on voltage ∼17 V for the device used mixture solvent compared to device prepared by toluene solvent. Apparently, the two different combination of aromatic and non-aromatic solvent significantly gives an effect on thin films properties and electrical properties of MEH-PPV OLED device.
  • Publication
    The structural and electrical characterization of PEDOT:PSS/MEH-PPV doped with PEIE OLED fabricated using spin coating technique
    ( 2020-01-08)
    Juhari N.
    ;
    Shukri N.I.A.
    ;
    Norhayati Sabani
    ;
    Safizan Shaari
    ;
    Mohd Fairus Ahmad
    ;
    Nor Farhani Zakaria
    This paper investigates the performance of the uniformity and absorption spectrum of MEHPPV+PEIE thin films also the electrical properties for configuration of ITO/PEDOT: PSS/MEH+PEIE/Al. The sample used 0.5 wt % of PEDOT: PSS solution while 5 mgml-1 concentration of MEH-PPV solution was doped with four different concentrations of PEIE with values of 0.1 wt%, 0.3 wt%, 0.5 wt% and 0.7 wt% respectively. The untreated PEDOT: PSS and MEH-PPV+PEIE was deposited using spin coating technique at a fixed spun speed of 3000 rpm to obtain smooth surface roughness thin film. The root mean square (RMS) value, absorption spectrum and current density (A/cm-2) of the PEDOT: PSS and MEH-PPV+PEIE films were analyzed using Atomic Force Microscope (AFM), UV-Visible (UV-Vis) Spectrophotometer and Semiconductor Parametric Analyzer (SPA), respectively. The surface roughness of the films were linearly increased when the dopant concentration increased with the maximum RMS value of ∼4.74 nm. Besides, absorption peak wavelength also was red-shifted from 500 nm to 551 nm under an influence of PEIE dopant concentrations. However, the turn on voltage gives no significant trend when dopant concentration was increased but the emission of the light was emitted when the voltage was below 8 V. Among four different dopant concentrations of MEH-PPV+PEIE, the brighter light emission was observed at 0.3 wt% of PEIE. Apparently, the concentration of dopant solution gives a significant contribution to the performance of OLED in terms of structural, optical and electrical properties.
  • Publication
    Low-cost tilt monitoring system for spin coater calibration
    ( 2024-02-08)
    King C.Y.
    ;
    Mohd Fairus Ahmad
    ;
    Norhayati Sabani
    ;
    Mohd Natashah Norizan
    ;
    Nor Farhani Zakaria
    ;
    Nurjuliana Juhari
    ;
    Shamsul Amir Abdul Rais
    ;
    Amin M.R.R.M.
    The spin coating process became the most widely used technique in the fabrication industry for thin film coating on a substrate by centrifugal force. Unfortunately, frequent usage of spin coater might induce a tilted surface of the chuck (i.e. the sample holder). A tilted chuck might induce inhomogeneity of the coating layer. Among the machine's calibration techniques, nullifying the tilt before the spin coating process is the most important step. However, to our knowledge, none of the spin coaters was introduced with the chuck's tilt monitoring during the spin coating process. Thus, investigating the discrete condition during the spin coating process is necessary. In this work, the tilt monitoring system for the spin coater was implemented based on an Arduino Uno microcontroller and distance sensor. A spin coater has been implemented to test the tilt surface monitoring during spinning ranges from 350rpm to 1000rpm. The measurement was done under two conditions: flat (0.00 degrees) and tilted (5.71 degrees). The setup was able to measure up to 0.01 degrees of the tilt.
  • Publication
    The efficiency effect of dye sensitized solar cell using different ratio of organic polymer doped titanium dioxide at different annealing process temperature
    ( 2020-01-08)
    Norhisamudin N.A.
    ;
    Norhayati Sabani
    ;
    Rosli N.
    ;
    Mohd Fairus Ahmad
    ;
    Juhari N.
    ;
    Safizan Shaari
    ;
    Zakaria N.
    Titanium Dioxide (TiO2) is one of the main materials in Dye Sensitized Solar Cell (DSSC). It is well known with its property of good optical transmittance and its mesoporous surface that can absorb generous amount of dye. In this study, TiO2 is fabricated using spin coating technique that leads to the uniform thickness of TiO2 layer. The thickness of the TiO2 can be controlled layer by layer using same technique to get an optimized surface that can lead to better performance of DSSC. In order to achieve this, the surface roughness of TiO2 must be as high as possible. Therefore, the organic material which is Poly(2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylene-vinylene (MEH-PPV) is used as medium to increase the mesoporous roughness structure of TiO2 nanocrystal film for DSSC. MEH-PPV is doped into the TiO2 using 0.5 mg/ml with different temperatures of 100°C and 450°C. Different temperatures of MEH-PPV will lead to the different surface structures for TiO2 thin film. The ratio of TiO2:MEH-PPV used were 1:1 and 2:1. The surface of TiO2 thin film was characterized using Atomic Force Microscope (AFM). The efficiency was obtained using Solar Simulator based on the voltage and current flow. Based on the results, the increment of surface roughness is about 21% for the different ratio at various temperatures. The optimum temperature and suitable ratio of TiO2:MEH-PPV was obtained via annealing process at 450°C with the ratio of 2:1. It gives the highest efficiency which is 0.1266%. These two important findings yield good mesoporous surface of TiO2 thin film.
  • Publication
    Temperature effects on electrical and structural properties of MEH-PPV/PEIE OLED Device
    ( 2020-06-16)
    Nurul Afiqah Nor Ismail
    ;
    Safizan Shaari
    ;
    Mohd Fairus Ahmad
    ;
    Norhayati Sabani
    ;
    Nurjuliana Juhari
    ;
    Nor Farhani Zakaria
    This paper explores the performance of configuration ITO/MEH-PPV/PEIE/Al OLED under the variations of temperature. The MEH-PPV and MEH-PPV/PEIE thin film were deposited on ITO substrates using spin coating technique with fixed spin speed of 3000 rpm and baked at low temperature ranging from 90 °C to 180 °C, respectively. The surface roughness values for MEH-PPV and MEH-PPV/PEIE films were analysed using AFM with 5 μm ' 5 μm scanning area. The roughness of MEH-PPV thin films were reduced from 2.825 nm to 1.625 nm when temperature increased. Contrary to MEH-PPV/PEIE films where the roughness increased linearly up to 3.397 nm when the temperature increased. The maximum absorption peak spectrum obtained from UV-Visible (UV-Vis) was found at 500 nm to 510 nm when baked temperature were varied. Furthermore, the turn on voltage from J-V characteristics gives no specific pattern across different temperature and agreed with the trend of surface roughness values. The turn-on voltage at T = 150 °C gives the lowest value of 3 V. Overall, the variations of low temperature gives an effects on structural and electrical properties of this OLED configuration.
      4  3
  • Publication
    Hybrid Cooling System for Solar Photovoltaic Panel
    ( 2023-01-01)
    Azmi M.S.F.M.
    ;
    Muhamad Hatta Hussain
    ;
    Siti Rafidah Abdul Rahim
    ;
    Ernie Che Mid
    ;
    Shaari A.S.
    ;
    Nurul Huda Hashim
    ;
    Husny N.
    ;
    Mohd Fairus Ahmad
    Solar photovoltaic (PV) panel is one of the renewable sources of energy and produced daily nowadays. Solar panel systems have efficiency influenced by different factors, such as ambient temperature, solar panel temperature, sunlight, weather, and irradiation. The increasing of the temperature of the solar PV panel decreases its efficiency and lifetime. Thus, to maintain and decrease the temperature of the PV cell, cooling system is required. This paper presents the hybrid (water and air) cooling system method for solar PV panel. The method has been designed and developed to lower and stable the operating temperature of the system considering different weather conditions. The results revealed that the hybrid cooling system has shown improvement of output power solar PV panel as compared with water cooling system only. Furthermore, the proposed method managed to improve efficiency approximately to 4.5%.
      1