Ayob Nazmy Nanyan
Thumbnail Image
Preferred name
Ayob Nazmy Nanyan
Official Name
Ayob Nazmy, Nanyan
Alternative Name
Nanyan, Ayob Nazmy
Nanyan, Ayob Nazmi Bin
Nanyan, A. N.
Main Affiliation
Scopus Author ID
57201667197
Researcher ID
FNW-5877-2022

Research Output

Filters

2 2
1
2
Reset filters

Settings
Now showing 1 - 2 of 2
  • Publication
    PCB Rogowski coil sensor by using saw blade pattern for arcing fault detection
    (IOP Publishing, 2023)
    Kamarul Aizat Abdul Khalid
    ;
    Muhammad Izuan Fahmi Romli
    ;
    Ayob Nazmy Nanyan
    ;
    Zul Hasrizal Bohari
    Rogowski is a special current transformer and has been categorised as a low-power stand-alone current sensor. This sensor is designed by using a Saw blade pattern with 50 turns and 100 turns. This number of turns will impact the increment of the sensitivity of the sensor. Rogowski coil is used for measuring the alternating current (AC) and high-speed current pulses. The PCB Rogowski Coil will detect the arcing fault that design with AutoCAD software after that import to CST software. An arc is created when the electrical current jumps the gap between two conductive materials. The most common causes of arcs include worn contacts in electrical equipment, damage to insulation, break in a cable and loose connections. In order to reduce the arc fault risk, the arc fault interrupter (AFI) technology and arc fault detectors (AFD) have been developed. However, these devices are most suitable for domestic application or low voltage (LV). This paper proposed a simulation using AutoCAD and CST software to design a Rogowski coil and the Rogowski Coil sensor will be tested by using CST software in terms of radiation pattern. The biggest radiation pattern in red colour is the saw blade pattern in 100 turns at 2 KHz frequency, the radiation pattern covering entire sensor area compared with other radiation patterns with other frequency. The main lobe magnitude for 2 KHz frequency is 46.8 dB, main lobe direction is 180 deg, angular width is 153.4 deg and the side lobe level is zero. This is the best number of turn and frequency compared to 50 turn saw blade sensor.
  • Publication
    Development of detachable Rogowski Coil current sensor using PCB for High Voltage cable partial discharge measurement
    ( 2022-01-01)
    Syed Akhmal Syed Jamalil
    ;
    Muzamir Isa
    ;
    Ahmad Zaidi Abdullah
    ;
    Ayob Nazmy Nanyan
    ;
    Bohari Z.H.
    Insulation failure in High Voltage (HV) cables is evaluated using a variety of monitoring techniques. Previous silicon technologies were outperformed by wide-bandgap semiconductor power devices with faster switching speeds. Their precise current management or current protection measures must be upgraded. As a result, their precise current control or protection measures have become more sophisticated. The traditional Rogowski Coil (RC) with the magnetic core, on the other hand, has low measurement accuracy, a short measuring range, and is difficult to fabricate. This paper presents and discusses the development of a Rogowski Coil using a detachable Printed Circuit Board (PCB) as a current sensor for Partial Discharge (PD) measurement. Furthermore, the development of this innovative current sensor concentrated on the detachable PCB Rogowski Coil's capability to measure as a high-voltage (HV) current sensor and its sensitivity in fault diagnosis, over-voltage current sensing, and high-impulse current sensing on HV cables. The experimental design, techniques, and measurement parameters used in models were discussed. Finally, a brief analysis of the detachable PCB RC current sensor such as sensitivity, maximum voltage and current detection is presented. This paper can also be used as a guideline for other researchers to develop an advanced RC current sensor using PCB as a HV current sensor in the future. The measurement results of the detachable PCB RC current sensor such as the sensitivity and current detection signal can also be used as a guideline by another researcher. As a result, the goal of this project is to measure PD on HV cables using an RC current sensor by utilising PCB technology.
      2  44